SAE AMS 5826E-2017 Steel Corrosion and Heat-Resistant Welding Wire 15Cr - 5 1Ni - 0 30Cb(Nb) - 3 2Cu (UNS S15500).pdf
《SAE AMS 5826E-2017 Steel Corrosion and Heat-Resistant Welding Wire 15Cr - 5 1Ni - 0 30Cb(Nb) - 3 2Cu (UNS S15500).pdf》由会员分享,可在线阅读,更多相关《SAE AMS 5826E-2017 Steel Corrosion and Heat-Resistant Welding Wire 15Cr - 5 1Ni - 0 30Cb(Nb) - 3 2Cu (UNS S15500).pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS5826E AEROSPACE MATERIAL SPECIFICATION AMS5826 REV. E Issued 1982-01 Reaffirmed 2011-10 Revi
5、sed 2017-06 Superseding AMS5826D Steel, Corrosion and Heat-Resistant, Welding Wire 15Cr - 5.1Ni - 0.30Cb(Nb) - 3.2Cu (Composition similar to UNS S15500) RATIONALE AMS5826E revises fabrication (3.3.2), winding (3.4.3.3), length (3.6.2), reports (4.4) and identification (5.2.1), and is a Five- Year Re
6、view and update of this specification. 1. SCOPE 1.1 Form This specification covers a corrosion and heat-resistant steel in the form of welding wire. 1.2 Application This wire has been used typically as filler metal for gas-tungsten-arc or gas-metal-arc welding of steels of similar composition requir
7、ing joints with strength and corrosion resistance comparable to those of the basis metal, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified
8、 herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available f
9、rom SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2248 Chemical Check Analysis Limits Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron
10、 Alloys AMS2371 Quality Assurance Sampling and Testing Corrosion and Heat-Resistant Steels and Alloys Wrought Products and Forging Stock AMS2813 Packaging and Marking of Packages of Welding Wire Standard Method SAE INTERNATIONAL AMS5826E Page 2 of 6 AMS2814 Packaging and Marking of Packages of Weldi
11、ng Wire Premium Quality AMS2816 Identification Welding Wire, Tab Marking Method AMS2819 Identification, Welding Wire Direct Color Code System ARP1876 Weldability Test for Weld Filler Metal Wire ARP1917 Clarification of Terms Used in Aerospace Metals Specifications ARP4926 Alloy Verification and Chem
12、ical Composition Inspection of Welding Wire 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM E353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium
13、-Nickel-Iron Alloys 3. TECHNICAL REQUIREMENTS 3.1 Composition Wire shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. Table 1 - Composition E
14、lement Min Max Carbon (3.1.4) Manganese Silicon Phosphorus Sulfur Chromium Nickel Columbium (Niobium) Copper Molybdenum Tantalum (3.1.1) Aluminum Oxygen Nitrogen Hydrogen 0.025 0.25 - - - 14.40 4.75 5XC 3.00 - - - - - - 0.050 0.75 0.60 0.020 0.010 15.30 5.50 0.40 3.50 0.30 0.05 0.025 0.01 (100 ppm)
15、0.040 (400 ppm) 0.0006 ( 6 ppm) SAE INTERNATIONAL AMS5826E Page 3 of 6 3.1.1 Determination not required for routine acceptance. 3.1.2 Check Analysis Composition variations shall meet the applicable requirements of AMS2248. 3.1.3 Chemical analysis of initial ingot, bar, or rod stock before drawing, o
16、ther than those analyses required to be done on the finished wire, is acceptable provided the processes used for drawing or rolling, annealing, and cleaning, are controlled to ensure continued conformance to chemical composition requirements. 3.1.4 Shall be determined on finished wire. 3.2 Condition
17、 Cold worked, bright finish, in a temper and with a surface finish which will provide proper feeding of the wire in machine welding equipment. 3.3 Fabrication 3.3.1 Wire shall be formed from rod or bar descaled by a process which does not affect the composition of the wire. Surface irregularities in
18、herent with a forming process that does not tear the wire surfaces are acceptable provided the wire conforms to the tolerances of 3.6. 3.3.2 Butt welding is permissible only at diameters larger than final finished product size provided both ends to be joined are alloy verified using a method capable
19、 of distinguishing the alloy from all other alloys processed in the facility, or the repair is made at the wire processing station. The butt weld shall not interfere with uniform, uninterrupted feeding of the wire in machine welding. 3.3.3 In-process annealing, if required, between cold rolling or d
20、rawing operations, shall be performed in vacuum or protective atmospheres to ensure freedom from surface oxidation and absorption of other extraneous elements. 3.3.4 Residual elements, drawing compounds, oxides, dirt, oil, dissolved gasses and other foreign materials picked up during wire processing
21、 that can adversely affect the welding characteristics, the operation of the equipment, or the properties of the weld metal, shall be removed by cleaning processes that will neither result in pitting nor cause gas absorption by the wire or deposition of substances harmful to welding operations. 3.4
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAMS5826E2017STEELCORROSIONANDHEATRESISTANTWELDINGWIRE15CR51NI030CBNB32CUUNSS15500PDF

链接地址:http://www.mydoc123.com/p-1022214.html