SAE AMS 5825H-2017 Steel Corrosion-Resistant Welding Wire 16 4Cr - 4 8Ni - 0 22Cb(Nb) - 3 6Cu (UNS S17480).pdf

《SAE AMS 5825H-2017 Steel Corrosion-Resistant Welding Wire 16 4Cr - 4 8Ni - 0 22Cb(Nb) - 3 6Cu (UNS S17480).pdf》由会员分享，可在线阅读，更多相关《SAE AMS 5825H-2017 Steel Corrosion-Resistant Welding Wire 16 4Cr - 4 8Ni - 0 22Cb(Nb) - 3 6Cu (UNS S17480).pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS5825H AEROSPACE MATERIAL SPECIFICATION AMS5825 REV. H Issued 1962-01 Reaffirmed 2011-10 Revi

5、sed 2017-07 Superseding AMS5825G Steel, Corrosion-Resistant, Welding Wire 16.4Cr - 4.8Ni - 0.22Cb(Nb) - 3.6Cu (Composition similar to UNS S17480) RATIONALE AMS5825H revises Fabrication (3.3.2), Winding (3.4.3.3), Length (3.6.2), Classification of Tests (4.2), Reports (4.4), and Identification (5.3.1

6、) and results from a Five-Year Review and update of this specification. 1. SCOPE 1.1 Form This specification covers a corrosion-resistant steel in the form of welding wire. 1.2 Application This wire has been used typically as bare wire filler metal for gas-tungsten-arc or gas-metal-arc welding of pa

7、rts fabricated from steels having composition similar to that of this wire, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The s

8、upplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE Intern

9、ational, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2248 Chemical Check Analysis Limits Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys AMS237

10、1 Quality Assurance Sampling and Testing Corrosion and Heat-Resistant Steels and Alloys Wrought Products and Forging Stock AMS2813 Packaging and Marking of Packages of Welding Wire Standard Method SAE INTERNATIONAL AMS5825H Page 2 of 6 AMS2814 Packaging and Marking of Packages of Welding Wire Premiu

11、m Quality AMS2816 Identification Welding Wire, Tab Marking Method AMS2819 Identification, Welding Wire Direct Color Code System AMS5643 Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0Cu Solution Heat Treated, Precipitation Hardenable AR

12、P1876 Weldability Test for Weld Filler Metal Wire ARP1917 Clarification of Terms Used in Aerospace Metals Specifications ARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West

13、Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM E18 Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials ASTM E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardn

14、ess, Scleroscope Hardness, and Leeb Hardness ASTM E353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys 3. TECHNICAL REQUIREMENTS 3.1 Wire Composition Shall conform to the percentages by weight shown in Table 1, determined by wet chemical method

15、s in accordance with ASTM E353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. Table 1 - Composition Element Min Max Carbon (3.1.1.1) Manganese Silicon Phosphorus Sulfur Chromium Nickel Columbium (Niobium) Copper Molybdenum - 0.25 - - - 16.00 4.50 0.15 3.25 - 0.0

16、5 0.75 0.75 0.025 0.025 16.75 5.00 0.30 4.00 0.75 3.1.1 Chemical analysis of initial bar or rod stock before drawing is acceptable provided the process used for drawing or rolling, annealing, and cleaning are controlled to ensure continued conformance to composition requirements. 3.1.1.1 Carbon shal

17、l also be determined periodically on finished wire (see 4.2.2). 3.1.2 Check Analysis Composition variations shall meet the applicable requirements of AMS2248. SAE INTERNATIONAL AMS5825H Page 3 of 6 3.2 Condition Cold worked, bright finished, in a temper and with a surface finish which will provide p

18、roper feeding of the wire in machine welding equipment. 3.2.1 Wire shall have a smooth finish that is free from slivers, depressions, scratches, scale, seams, laps, and foreign matter that would adversely affect welding characteristics, operation of the welding equipment, or properties of the weld m

19、etal. 3.3 Fabrication 3.3.1 Wire shall be formed from rod or bar descaled by a process which does not affect the composition of the wire. Surface irregularities inherent with a forming process that does not tear the wire surfaces are acceptable provided the wire conforms to the tolerances of 3.6. 3.

20、3.2 Butt welding is permissible only at diameters larger than final finished product size provided both ends to be joined are alloy verified using a method capable of distinguishing the alloy from all other alloys processed in the facility, or the repair is made at the wire processing station. The b

21、utt weld shall not interfere with uniform, uninterrupted feeding of the wire in machine welding. 3.3.3 In-process annealing, if required, between cold rolling or drawing operations, shall be performed in a vacuum or a protective atmosphere to ensure freedom from surface oxidation and absorption of o

22、ther extraneous elements. 3.3.4 Residual elements, drawing compounds, oxides, dirt, oil, dissolved gasses and other foreign materials picked up during wire processing that can adversely affect the welding characteristics, the operation of the equipment, or the properties of the weld metal, shall be

23、removed by a cleaning processes that will neither result in pitting nor cause gas absorption by the wire or deposition of substances harmful to welding operations. 3.4 Properties Wire shall conform to the following requirements: 3.4.1 Weldability Melted wire shall flow smoothly and evenly during wel

24、ding and shall produce acceptable welds. ARP1876 may be used to resolve disputes. 3.4.2 Response to Heat Treatment Weld metal, approximately 1/4 inch (6.4 mm) in thickness, deposited on AMS5643 steel shall attain hardness not lower than 38 HRC, or equivalent (see 8.2), determined in accordance with

25、ASTM E18, after being solution heat treated by heating to 1900 F 25 F (1038 C 14 C), holding at heat for not less than 30 minutes, and cooling to below 60 F (16 C) and precipitation heat treated by heating to 900 F 10 F (482 C 6 C), holding at heat for 60 minutes 5 minutes, and cooling in air. 3.4.3

26、 Spooled Wire Shall conform to 3.4.3.1 and 3.4.3.2. 3.4.3.1 Cast Wire, wound on standard 12 inch (305 mm) diameter spools, shall have imparted to it a curvature such that a specimen sufficient in length to form one loop with a 1 inch (25 mm) overlap, when cut from the spool and laid on a flat surfac

27、e, shall form a circle 15 to 50 inches (381 to 1270 mm) in diameter. 3.4.3.2 Helix The specimen on which cast was determined, when laid on a flat surface and measured between adjacent turns, shall show a vertical separation not greater than 1 inch (25 mm). SAE INTERNATIONAL AMS5825H Page 4 of 6 3.4.

28、3.3 Winding Filler metal in coils and on spools shall be wound so that kinks, waves, sharp bends, overlapping, or wedging are not encountered, leaving the filler metal free to unwind without restriction. The outside end of the electrode (the end where welding is to begin) shall be identified so it c

29、an be located readily and shall be fastened to avoid unwinding. The winding on spools shall be level winding. 3.5 Quality Wire, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to welding operations, operat

30、ion of welding equipment, or properties of the deposited weld metal. 3.6 Sizes and Tolerances Wire shall be supplied in the sizes and to the tolerances shown in Table 2 and 3.6.2. 3.6.1 Diameter Shall be as shown in Table 2. Table 2 Table 2A- Diameters and tolerances, inch/pound units Form Nominal D

31、iameter Inch Tolerance Inch Plus and Minus Cut Lengths Cut Lengths Spools Spools Spools 0.030, 0.035, 0.045 0.062, 0.078, 0.094, 0.125, 0.156, 0.187 0.007, 0.010, 0.015 0.020, 0.030, 0.035, 0.045 0.062, 0.078, 0.094 0.001 0.002 0.0005 0.001 0.002 Table 2B- Diameters and tolerances, SI units Form Nom

32、inal Diameter Millimeters Tolerance Millimeter Plus and Minus Cut Lengths Cut Lengths Spools Spools Spools 0.76, 0.89, 1.14 1.57, 1.98, 2.39, 3.18, 3.96, 4.75 0.18, 0.25, 0.38 0.51, 0.76, 0.89, 1.14 1.57, 1.98, 2.39 0.025 0.05 0.013 0.025 0.05 3.6.2 Length Cut lengths shall be furnished in 18, 27, o

33、r 36 inch (457, 686, or 914 mm) lengths, or other lengths when specified by purchaser, and shall not vary more than +0, -0.5 inch (+0, -13 mm) from the length ordered. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The producer of wire shall supply all samples for producers tests

34、and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements. SAE INTERNATIONAL AMS5825H Page 5 of 6 4.2 Classification of Tests 4.2.1 Acc

35、eptance Tests Composition (3.1), tolerances (3.6), and alloy verification (5.2.1) are acceptance tests and shall be performed on each heat or lot as applicable. 4.2.2 Periodic Tests Determination of carbon on finished wire (3.1.1.1), weldability (3.4.1), response to heat treatment (3.4.2), cast (3.4

36、.3.1), and helix (3.4.3.2) are periodic tests and shall be performed at a frequency selected by the producer unless frequency of testing is specified by purchaser. 4.3 Sampling and Testing Shall be in accordance with AMS2371 and as specified herein. 4.4 Reports The producer of wire shall furnish wit

37、h each shipment a report showing the results of tests for composition and response to heat treatment of each heat, and stating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5825H, nominal size, form, and quan

38、tity. 4.4.1 When material produced to this specification has exceptions taken to the technical requirements listed in Section 3 (see 5.3.1), the report shall contain a statement “This material is certified as AMS5825H (EXC) because of the following exceptions.” The specific exceptions shall be liste

39、d. 4.5 Resampling and Retesting Shall be in accordance with AMS2371. 5. PREPARATION FOR DELIVERY 5.1 Wire shall be supplied either on spools in one continuous length for machine welding or in cut lengths for manual welding, as ordered. Wire on each spool or in each package of cut lengths shall be fr

40、om the same heat of steel. 5.2 Alloy Verification 5.2.1 Wire from each spool or package of cut lengths shall be alloy verified by a method acceptable to purchaser. The alloy verification methods of ARP4926 are recommended. 5.2.2 An 8 inch (203 mm) length of wire shall be made accessible at both ends

41、 of each spool for alloy verification. 5.3 Identification Shall be in accordance with AMS2816 unless AMS2819 or another method is specified by purchaser. 5.3.1 When technical exceptions are taken (see 4.4.1), the material shall be marked with AMS5825H (EXC). 5.4 Packaging and Marking Shall be in acc

42、ordance with AMS2813 unless AMS2814 or another method is specified by purchaser. SAE INTERNATIONAL AMS5825H Page 6 of 6 6. ACKNOWLEDGMENT A producer shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Wire not confor

43、ming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 Revision Indicator A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to

44、the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Hardness conversion

45、tables for metals are presented in ASTM E140. 8.3 Terms used in this AMS are clarified in ARP1917. 8.4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.5 Purchase documents should specify not less than the following: AMS5825H Size and form (spools or cut lengths) of wire desired Length of cut lengths or weight of spools desired Quantity of wire desired PREPARED BY AMS COMMITTEE “F“