SAE AMS 5519N-2008 Steel Corrosion Resistant Sheet and Strip 18Cr C 8Ni (SAE 30301) Cold Rolled 185 ksi (1276 MPa) Tensile Strength (UNS S30100)《18Cr 8Ni(SAE 30301)拉伸强度为185ksi(1276.pdf

《SAE AMS 5519N-2008 Steel Corrosion Resistant Sheet and Strip 18Cr C 8Ni (SAE 30301) Cold Rolled 185 ksi (1276 MPa) Tensile Strength (UNS S30100)《18Cr 8Ni(SAE 30301)拉伸强度为185ksi(1276.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 5519N-2008 Steel Corrosion Resistant Sheet and Strip 18Cr C 8Ni (SAE 30301) Cold Rolled 185 ksi (1276 MPa) Tensile Strength (UNS S30100)《18Cr 8Ni(SAE 30301)拉伸强度为185ksi(1276.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5519N AEROSPACE MATERIAL SPECIFICATION AMS5519 REV. N Issued 1940-01 Revised 2

5、008-12 Reaffirmed 2014-06 Superseding AMS5519M Steel, Corrosion Resistant, Sheet and Strip 18Cr 8Ni (SAE 30301) Cold Rolled, 185 ksi (1276 MPa) Tensile Strength (Composition similar to UNS S30100) RATIONALE This document has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE 1.

6、1 Form This specification covers a corrosion-resistant steel in the form of sheet and strip. 1.2 Application These products have been used typically for parts requiring moderate drawing or forming and high strength, but usage is not limited to such applications. 1.2.1 Mechanical properties specified

7、 herein are obtained by cold working (strain hardening) and not by heat treatment. Therefore, the cold-worked product should not be heated to a temperature which adversely affects the mechanical properties or corrosion resistance before, during, or after fabrication. 2. APPLICABLE DOCUMENTS The issu

8、e of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and

9、no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2242 T

10、olerances, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Sheet, Strip, and Plate AMS2248 Chemical Check Analysis Limits, Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys AMS2371 Quality Assurance Sampling and Tes

11、ting, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock SAE INTERNATIONAL AMS5519N Page 2 of 5 AMS2807 Identification, Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys, Sheet, Strip, Plate, and Aircraft Tubing 2.2 ASTM Publications Availabl

12、e from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM A 370 Mechanical Testing of Steel Products ASTM E 290 Bend Testing of Material for Ductility ASTM E 353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, a

13、nd Other Similar Chromium-Nickel-Iron Alloys ASTM E 384 Microindentation Hardness of Materials 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 353, by spectrochemical methods, or by ot

14、her analytical methods acceptable to purchaser. TABLE 1 - COMPOSITION Element min max Carbon - 0.15 Manganese - 2.00 Silicon - 1.00 Phosphorus - 0.040Sulfur - 0.030Chromium 16.00 18.00 Nickel 6.00 8.00 Molybdenum - 0.75 Copper - 0.75 3.1.1 Check Analysis Composition variations shall meet the applica

15、ble requirements of AMS2248. 3.2 Condition Solution heat treated, descaled unless solution heat treatment is performed in an atmosphere yielding a bright finish, and cold rolled (See 8.2). 3.3 Properties The product shall conform to the following requirements. Tensile and hardness testing shall be p

16、erformed in accordance with ASTM A 370: SAE INTERNATIONAL AMS5519N Page 3 of 5 3.3.1 Tensile Properties Product 0.005 inch (0.13 mm) and over in nominal thickness shall have the properties shown in Table 2. TABLE 2 - MINIMUM TENSILE PROPERTIES Property Value Tensile Strength 185 ksi (1276 MPa) Yield

17、 Strength at 0.2% Offset 140 ksi ( 965 MPa) Elongation in 2 Inches (50.8 mm) Nominal Thickness Up to 0.015 Inch (0.38 mm), incl Over 0.015 Inch (0.38 mm) 8% 9% 3.3.2 Hardness Shall be not lower than 41 HRC or equivalent (See 8.3). Product shall not be rejected on the basis of hardness if tensile pro

18、perties of 3.3.1 are acceptable, determined on specimens taken from the same sample as that with nonconforming hardness or from another sample with similar nonconforming hardness. 3.3.2.1 Microhardness testing in accordance with ASTM E 384 may be used for thin gages where superficial hardness testin

19、g is impractical. 3.3.3 Bending Product shall be tested in accordance with ASTM E 290 using a sample prepared nominally 0.75 inch (19.0 mm) in width, with its axis parallel to the direction of rolling, and shall withstand, without cracking, when bending at room temperature through the angle indicate

20、d in Table 3 around a diameter equal to the bend factor times the nominal thickness of the product. In case of dispute, the results of tests using the guided bend test of ASTM E 290 shall govern. TABLE 3 - BENDING PARAMETERS Nominal Thickness Inch Nominal Thickness Millimeters Angle deg, min Bend Fa

21、ctor Up to 0.030, incl Up to 0.76, incl 180 4 Over 0.030 Over 0.76 90 3 3.4 Quality The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product. 3.5 Tolerances Shall conform to all

22、 applicable requirements of AMS2242. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of the product shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any co

23、nfirmatory testing deemed necessary to ensure that the product conforms to specified requirements. SAE INTERNATIONAL AMS5519N Page 4 of 5 4.2 Classification of Tests All technical requirements are acceptance tests and shall be performed on each heat or lot as applicable. 4.3 Sampling and Testing Sha

24、ll be in accordance with AMS2371. 4.4 Reports The vendor of the product shall furnish with each shipment a report showing the results of tests for composition of each heat and for tensile, hardness, and bending properties of each lot, and stating that the product conforms to the other technical requ

25、irements. This report shall include the purchase order number, heat and lot numbers, AMS5519N, size, and quantity. 4.5 Resampling and Retesting Shall be in accordance with AMS2371. 5. PREPARATION FOR DELIVERY 5.1 Identification Shall be in accordance with AMS2807. 5.2 Packaging The product shall be

26、prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall mention this specification nu

27、mber and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (|) located in the left margin is for the convenienc

28、e of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revision. Change bars and (R) are not used in origi

29、nal publications, nor in documents that contain editorial changes only. 8.2 This condition may sometimes be designated “TR” by the producing mill. 8.3 Hardness conversion tables for metals are presented in ASTM E 140. 8.4 Terms used in AMS are clarified in ARP1917. 8.5 Dimensions and properties in i

30、nch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. SAE INTERNATIONAL AMS5519N Page 5 of 5 8.6 Purchase documents should s

31、pecify not less than the following: AMS5519N Form and size of product desired Quantity of product desired. 8.7 Similar Specifications MIL-S-5059D, Type 301, Full Hard, is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. PREPARED BY AMS COMMITTEE “F“