SAE AMS 4611H-2003 Brass Naval Bars and Rods 60 5Cu - 38 7Zn - 0 8Sn Half Hard (H02) (UNS C46400)《60 5Cu 38 7Zn 0 8Sn半硬度船用黄铜棒材和杆材(H02)》.pdf

《SAE AMS 4611H-2003 Brass Naval Bars and Rods 60 5Cu - 38 7Zn - 0 8Sn Half Hard (H02) (UNS C46400)《60 5Cu 38 7Zn 0 8Sn半硬度船用黄铜棒材和杆材(H02)》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 4611H-2003 Brass Naval Bars and Rods 60 5Cu - 38 7Zn - 0 8Sn Half Hard (H02) (UNS C46400)《60 5Cu 38 7Zn 0 8Sn半硬度船用黄铜棒材和杆材(H02)》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4611H AEROSPACE MATERIAL SPECIFICATION AMS4611 REV. H Issued 1942-12 Revised 2

5、003-10 Reaffirmed 2014-04 Superseding AMS4611G Brass, Naval, Bars and Rods 60.5Cu - 38.7Zn - 0.8Sn Half Hard (H02) (Composition similar to UNS C46400) RATIONALE AMS4611H has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE: 1.1 Form: This specification covers a copper alloy (

6、naval brass) in the form of bars and rods. 1.2 Applications: These products have been used typically for automatic screw machine parts, but usage is not limited to such applications. These products have better corrosion resistance than AMS 4610 but are less readily machinable. 2. APPLICABLE DOCUMENT

7、S: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been can

8、celled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org. AMS 2221 Tolerances, Copper and Copper Alloy Bars and Rods AMS 4610 Brass, Free-Cu

9、tting, Bars and Rods, 61.5Cu - 35Zn - 3.1Pb Half Hard (H02) SAE INTERNATIONAL AMS4611H Page 2 of 6 2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or www.astm.org. ASTM B 154 Mercurous Nitrate Test for Copper and Copper Alloys ASTM B 249 General Re

10、quirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes, and Forgings ASTM B 249M General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes, and Forgings (Metric) ASTM B 858 Ammonia Vapor Test for Determination of Susceptibility to Stress Corrosion Cracking in Copper Alloys A

11、STM E 8 Tension Testing of Metallic Materials ASTM E 8M Tension Testing of Metallic Materials (Metric) ASTM E 478 Chemical Analysis of Copper Alloys 3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordan

12、ce with ASTM E 478, by spectrochemical methods, or by other analytical methods acceptable to purchaser. TABLE 1 - Composition Element (3.1.1) min maxCopper 59.0 62.0Tin 0.50 1.0Lead - 0.20Iron - 0.10Sum of Named Elements (3.1.3) 99.6 - Zinc (See 3.1.2) remainder 3.1.1 These composition limits do not

13、 preclude the presence of other elements. Limits may be established and analysis required for unnamed elements by agreement between the manufacturer or supplier and purchaser. 3.1.2 Zinc may be reported as “remainder”, as the difference between the sum of results for all elements and 100%, or as the

14、 result of direct analysis. 3.1.3 When all named elements in Table 1 are analyzed, the sum shall be 99.6 percent minimum, but such determination is not required for routine acceptance of each lot. 3.2 Condition: Cold finished, half-hard (H02) temper (See 8.2). SAE INTERNATIONAL AMS4611H Page 3 of 6

15、3.3 Properties: The product shall conform to the following requirements: 3.3.1 Tensile Properties: Shall be as shown in Table 2, determined in accordance with ASTM E 8 or ASTM E 8M except as specified in 4.3.2.1. TABLE 2A - Minimum Tensile Properties, Inch/Pound Units Nominal Thickness Inches Tensil

16、e Strength ksi Yield Strengthat 0.2% Offsetksi Elongation in 2 Inches or 4D %, min Up to 0.500, incl 60.0 27.0 22 (See 3.3.1.1)Over 0.500 to 1.000, incl 60.0 27.0 25 Over 1.000 to 2.500, incl 58.0 26.0 25 Over 2.500 to 3.500, incl 54.0 25.0 27 Over 3.500 54.0 22.0 30 TABLE 2B - Minimum Tensile Prope

17、rties, SI Units Nominal Thickness Millimeters Tensile Strength MPa Yield Strengthat 0.2% OffsetMPa Elongation in 50.8 mm or 4D %, min Up to 12.70, incl 414 186 22 (See 3.3.1.1)Over 12.70 to 25.40, incl 414 186 25 Over 25.40 to 63.50, incl 400 179 25 Over 63.50 to 88.90, incl 372 172 27 Over 88.90 37

18、2 152 30 3.3.1.1 In no case shall the gage length be less than 1 inch (25 mm). 3.3.2 Embrittlement: Specimens as in 4.3.3.1 shall withstand, without cracking, immersion in mercurous nitrate solution in accordance with ASTM B 154, Procedure A, or the Ammonia Vapor Test in accordance with ASTM B 858.

19、3.4 Quality: The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product. 3.5 Tolerances: Shall conform to AMS 2221 as applicable to nonrefractory alloys. SAE INTERNATIONAL AMS4611

20、H Page 4 of 6 4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of the product shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing de

21、emed necessary to ensure that the product conforms to specified requirements. 4.2 Classification of Tests: All technical requirements are acceptance tests and shall be performed on each lot. 4.3 Sampling and Testing: Shall be in accordance with ASTM B 249 or ASTM B 249M and the following: 4.3.1 Comp

22、osition: One sample from each lot. 4.3.2 Tensile Properties: One sample from each lot. 4.3.2.1 Tensile tests shall be performed on full-section specimens when practicable. When machined specimens are required, the axis of the specimen shall coincide with the central axis of the piece except that for

23、 bars and rods over 1.50 inches (38.1 mm) in nominal diameter or distance between parallel sides, the axis shall be midway between center and surface of the piece. The longitudinal axis of the tensile specimen shall be parallel to the direction of rolling or drawing. 4.3.3 Embrittlement: One sample

24、from each lot, unless otherwise agreed upon by purchaser and vendor. 4.3.3.1 Specimens for embrittlement test shall be full cross-sections of the product and shall have length of approximately 6 inches (152 mm) or twice the nominal diameter or least distance between parallel sides, whichever is grea

25、ter. 4.4 Reports: The vendor of the product shall furnish with each shipment a report showing the results of tests for chemical composition, tensile properties, and embrittlement of each lot and stating that the product conforms to the other technical requirements. This report shall include the purc

26、hase order number, lot number, AMS 4611H, size, and quantity. 4.5 Resampling and Retesting: If any specimen used in the above tests fails to meet specified requirements, disposition of the product may be based on the results of testing two additional specimens for each original nonconforming specime

27、n. Failure of any retest specimen to meet specified requirements shall be cause for rejection of the product represented. Results of all tests shall be reported. SAE INTERNATIONAL AMS4611H Page 5 of 6 5. PREPARATION FOR DELIVERY: 5.1 Identification: Individual pieces or bundles shall have attached a

28、 durable tag legibly marked with not less than the purchase order number, AMS 4611H, lot number, and nominal size, or shall be boxed and the box marked with the same information. 5.2 Packaging: The product shall be prepared for shipment in accordance with commercial practice and in compliance with a

29、pplicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase order

30、s. 7. REJECTIONS: Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES: 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes,

31、have been made to the previous issue of a specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical revision. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes o

32、nly. 8.2 Copper temper designations are defined in ASTM B 601. 8.3 Terms used in AMS are clarified in ARP1917. 8.4 Dimensions and properties in inch/pound units are primary; dimensions and properties in SI units are shown as the approximate equivalents of the primary units and are presented only for

33、 information. 8.5 Purchase documents should specify not less than the following: AMS 4611H Form and size of product desired Quantity of product desired. SAE INTERNATIONAL AMS4611H Page 6 of 6 8.6 Similar Specification: ASTM B 21, C46400, is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “D”