SAE AMS 4083L-2012 Aluminum Alloy Tubing Hydraulic Seamless Drawn Round 1 0Mg - 0 60Si - 0 28Cu - 0 20Cr (6061-T6) Solution and Precipitation Heat Treated (UNS 96061)《1 0Mg 0 60Si .pdf
《SAE AMS 4083L-2012 Aluminum Alloy Tubing Hydraulic Seamless Drawn Round 1 0Mg - 0 60Si - 0 28Cu - 0 20Cr (6061-T6) Solution and Precipitation Heat Treated (UNS 96061)《1 0Mg 0 60Si .pdf》由会员分享,可在线阅读,更多相关《SAE AMS 4083L-2012 Aluminum Alloy Tubing Hydraulic Seamless Drawn Round 1 0Mg - 0 60Si - 0 28Cu - 0 20Cr (6061-T6) Solution and Precipitation Heat Treated (UNS 96061)《1 0Mg 0 60Si .pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2012 SAE International All rights reserved. No part of this publication m
3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U
4、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4083L AEROSPACE AEROSPACE MATERIAL SPECIFICATION AMS4083 REV. L Issued 1948-11 Revised 201
5、2-11 Superseding AMS4083K Aluminum Alloy Tubing, Hydraulic, Seamless, Drawn, Round 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated (Composition similar to UNS 96061) RATIONALE AMS4083L corrects the calculation of hydraulic strength (3.3.4), revises acceptance crite
6、ria for eddy current inspection (3.4.3.2), and results from a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specification covers an aluminum alloy in the form of seamless round tubing. 1.2 Application This tubing has been used typically for parts operating under high pres
7、sure, such as hydraulic systems and fuel and oil lines, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to
8、a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonw
9、ealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2355 Quality Assurance Sampling and Testing, Aluminum Alloys and Magnesium Alloys, Wrought Products, Except Forging Stock, and Rolled, Forged, or Flash Welded Rings AMS277
10、2 Heat Treatment of Aluminum Alloy Raw Materials SAE AMS4083L Page 2 of 7 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM B 660 Packaging/Packing of Aluminum and Magnesium Products
11、ASTM B 666/B 666M Identification Marking of Aluminum Products ASTM E 215 Standardizing Equipment for Electromagnetic Testing of Seamless Aluminum-Alloy Tube 2.3 ANSI Publications Available from American National Standards Institute, 25 West 43rd Street, New York, NY 10036, Tel: 212-642-4900, www.ans
12、i.org. ANSI H35.2 Dimensional Tolerances for Aluminum Mill Products ANSI H35.2M Dimensional Tolerances for Aluminum Mill Products (Metric) 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table 1, determined in accordance with AMS2355. TABLE 1 - COMPOSITI
13、ON Element min max Silicon Iron Copper Manganese Magnesium Chromium Zinc Titanium Others, each Others, total Aluminum 0.40 - 0.15 - 0.8 0.04 - - - - remainder 0.8 0.7 0.40 0.15 1.2 0.35 0.25 0.15 0.05 0.15 3.2 Condition Solution and precipitation heat treated in accordance with AMS2772. 3.2.1 Tubing
14、 shall be supplied unground with an as-drawn surface finish, unless otherwise specified by purchaser. 3.3 Properties Tubing shall conform to the following requirements, determined on the mill produced size in accordance with AMS2355, except as specified in 3.4.3.2: 3.3.1 Tensile Properties Shall be
15、as specified in Table 2: SAE AMS4083L Page 3 of 7 TABLE 2A - MINIMUM TENSILE PROPERTIES, INCH/POUND UNITS Nominal Wall Thickness Inch Tensile Strength ksi Yield Strength at 0.2% Offset ksi Elongation in 2 Inches or 4D Cut Out Specimen % Elongation in 2 Inches or 4D Full Section Specimen % 0.025 to 0
16、.049, incl Over 0.049 to 0.259, incl Over 0.259 to 0.500, incl 42.0 42.0 42.0 35.0 35.0 35.0 8 10 12 10 12 14 TABLE 2B - MINIMUM TENSILE PROPERTIES, SI UNITS Nominal Wall Thickness Millimeters Tensile Strength MPa Yield Strength at 0.2% Offset MPa Elongation in 50.8 mm or 4D Cut Out Specimen % Elong
17、ation in 50.8 mm or 4D Full Section Specimen % 0.64 to 1.24, incl Over 1.24 to 6.58, incl Over 6.58 to 12.70, incl 290 290 290 241 241 241 8 10 12 10 12 14 3.3.2 Flattening Tubing having nominal wall thickness less than 10% of the nominal OD shall withstand, without cracking, flattening sideways und
18、er a load applied gradually at room temperature until the outside dimension under load is equal to eight times the nominal wall thickness. Tubing having nominal wall thickness 10% or more of the nominal OD shall withstand without cracking, flattening sideways under a load applied gradually at room t
19、emperature until the outside dimension under load equals 90% of the nominal OD. 3.3.2.1 If tubing does not pass the flattening test of 3.3.2, a section of tube not less than 0.5 inch (12.7 mm) in length and embracing one-third to one-half the circumference of the tube shall withstand, without cracki
20、ng, bending at room temperature through an angle of 180 degrees around a mandrel having a diameter equal to 6 times the nominal wall thickness of the tubing with axis of bend parallel to axis of tube and with inside of tube on inside of bend. 3.3.3 Flarability Specimens as in 4.3.1 from tubing 0.375
21、 inch (9.52 mm) and under in nominal OD shall withstand being double-flared (See 8.2) and from tubing over 0.375 inch (9.52 mm) in nominal OD shall withstand being single flared without formation of cracks or other visible defects by being forced axially, at room temperature, with steady pressure ov
22、er a hardened and polished tapered steel pin having a 74-degree included angle to produce a flare having a permanent expanded OD not less than specified in Table 3. TABLE 3A - FLARABILITY REQUIREMENTS, INCH/POUND UNITS Nominal OD Inch Expanded OD Inch Nominal OD Inches Expanded OD Inches 0.125 0.200
23、 1.000 1.187 0.188 0.302 1.250 1.500 0.250 0.359 1.500 1.721 0.312 0.421 1.750 2.106 0.375 0.484 2.000 2.356 0.500 0.656 2.500 2.856 0.625 0.781 3.000 3.356 0.750 0.937 SAE AMS4083L Page 4 of 7 TABLE 3B - FLARABILITY REQUIREMENTS, SI UNITS Nominal OD Millimeters Expanded OD Millimeters Nominal OD Mi
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAMS4083L2012ALUMINUMALLOYTUBINGHYDRAULICSEAMLESSDRAWNROUND10MG060SI028CU020CR6061T6SOLUTIONANDPRECIPITATIONHEATTREATEDUNS9606110MG060SIPDF

链接地址:http://www.mydoc123.com/p-1021354.html