SAE AMS 3898 5B-1994 Interleaf Carrier Material Composite Tape Polyethylene Coated Paper Perforated 0 0035 inch (0 089 mm)《无孔的0 0035 in(0 089 mm)复合带聚乙烯薄膜涂层纸插页载体材料》.pdf

《SAE AMS 3898 5B-1994 Interleaf Carrier Material Composite Tape Polyethylene Coated Paper Perforated 0 0035 inch (0 089 mm)《无孔的0 0035 in(0 089 mm)复合带聚乙烯薄膜涂层纸插页载体材料》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 3898 5B-1994 Interleaf Carrier Material Composite Tape Polyethylene Coated Paper Perforated 0 0035 inch (0 089 mm)《无孔的0 0035 in(0 089 mm)复合带聚乙烯薄膜涂层纸插页载体材料》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、1. SCOPE:1.1 Form:This specification covers one type of paper, coated on both sides withpolyethylene film, of the width specified herein.2. APPLICABLE DOCUMENTS:See AMS 3898.3. TECHNICAL REQUIREMENTS:3.1 Basic Specification:The complete requirements for procuring the product described herein shallco

2、nsist of this document and the latest issue of the basic specification,AMS 3898.3.2 Material:The carrier material shall be paper coated on each side with a polyethylenefilm, slit to the width specified, and perforated for sprocket alignment asshown in Figure 1 of AMS 3898.3.2.1 Thickness: Shall be 0

3、.0035 inch 0.0005 (0.089 mm 0.013).3.2.2 Width: Shall be 4.000 inches (101.60 mm).AEROSPACE MATERIAL SPECIFICATIONAMS3898/5 REV. B Issued 1975-06Revised 1994-02Reaffirmed 2014-08Superseding AMS3898/5AInterleaf Carrier Material, Composite TapePolyethylene Coated Paper, Perforated0.0035 inch (0.089 mm

4、)RATIONALEAMS3898/5B has been reaffirmed to comply with the SAE five year review policy._SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability

5、and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments an

6、d suggestions.Copyright 2014 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.877-6

7、06-7323 (inside USA and Canada)TO PLACE A DOCUMENT ORDER: Tel: Tel: +1 724-776-4970 (outside USA)SAE WEB ADDRESS:Fax: 724-776-0790Email: CustomerServicesae.orghttp:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS389

8、8/5B3.3 Properties:Shall be as shown in Table 1.TABLE 1 PropertiesParagraph Property Requirement Test Method3.3.1 Tensile Strength, minimum 25 pounds forceper inch(4.38 kN/m) of widthASTM D 882,Method A3.3.2 Tear Strength, minimum 0.75 ounce force(209 mN)ASTM D 827-714. QUALITY ASSURANCE PROVISIONS:See AMS 3898.5. PREPARATION FOR DELIVERY:See AMS 3898.6. ACKNOWLEDGMENT:See AMS 3898.7. REJECTIONS:See AMS 3898.8. NOTES:See AMS 3898.SAE INTERNATIONAL AMS3898/5B Page 2 of 2