SAE AMS 3894 5B-1989 Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 110 000 (758) Tensile 27 000 000 (186) Modulus 80 (176)《G110 000(758)拉力、27 000 000(186)模数、80(176)的环氧树脂浸渍的.pdf

《SAE AMS 3894 5B-1989 Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 110 000 (758) Tensile 27 000 000 (186) Modulus 80 (176)《G110 000(758)拉力、27 000 000(186)模数、80(176)的环氧树脂浸渍的.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 3894 5B-1989 Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 110 000 (758) Tensile 27 000 000 (186) Modulus 80 (176)《G110 000(758)拉力、27 000 000(186)模数、80(176)的环氧树脂浸渍的.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE MATERIAL SPECIFICATION Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 110,000 (758) Tensile, 27,000,000 (186) Modulus, 80 (176) SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of

2、this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or c

3、ancelled. SAE invites your written comments and suggestions. Copyright 2005 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, w

4、ithout the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org AMS 3894/5BIssued NOV 1972 Revised JAN 1989 Reaffirmed JUN 2005 Superseding AMS

5、3894/5A 1. SCOPE:1.1 Form: This specification covers one type of epoxy-resin-impregnated carbonfibers in the form of tape and sheet.1.2 Application: Primarily for use in structural composites requiring highmodulus of elasticity in tension up to 80C (176F).1.3 Classification: G 110,000 psi (758 MPa)

6、tensile strength, (186 GPa) tensile modulus carbon fiber impregnated with epoxy resin forservice up to 80C (176F).2. APPLICABLE DOCUMENTS: See AMS 3894.3. TECHNICAL REOUIREMENTS:3.1 Basic Specification: The complete requirements for procuring the productdescribed herein shall consist of this documen

7、t and the latest issue of thebasic specification, AMS 3894.3.2 Material: The product shall be AMS 3892/2 high modulus carbon fibersimpregnated with epoxy resin formulated to meet the requirements specifiedherein.3.2.1 Storage Life: The product shall meet the requirements of thisspecification when te

8、sted at any time up to six months from date ofreceipt by purchaser provided it has been stored in the original unopenedcontainers at not higher than -18C (0F).3.2.2 Working Life: The product shall meet the requirements of thisspecification when tested after continuous exposure for up to 20 dayswithi

9、n the relative humidity and temperature limits shown in Fig. 1.27,000,000 psiCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE - 2 - AMS 3894/5B AMS 3894/5BFigure 13.3 Properties of Uncured Impregn

10、ated Product: Shall be as specified in 3.3.1through 3.3.5. Tests shall be performed on the product after warming toabove the dew point prior to sampling and in accordance with test methodslisted in the basic specification.3.3.1 Volatile Content, % of resinweight, maximum1.5Test temperature: 150C 5(3

11、02F 9)Test time: 15 - 60 minutes3.3.2 Resin Solids Content, % by weight Preproduction Value 33.3.3 Resin Flow, % by weight3.3.4 Gel Time, minutes3.3.5 Tack10 - 30Preproduction Value 10%Shall adhere for not lessthan 30 minutes3.4 Properties of Cured Laminates: Shall be as follows, determined on speci

12、menscut from a test panel prepared as specified in the basic specification andtested in accordance with test methods specified therein:3.4.1 Mechanical Properties: Shall be as specified in Table I.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or netw

13、orking permitted without license from IHS-,-,-SAE - 3 - AMS 3894/5B AMS 3894/5B3.4.2 Density: Shall be determined on the test laminate used to determinemechanical properties; values for each test laminate shall be reported.Fiber density and cured resin density shall also be reported.3.4.3 Void Conte

14、nt: Shall be not greater than 1%.4. OUALITY ASSURANCE PROVISIONS: See AMS 3894.5. PREPARATION FOR DELIVERY: Shall be in accordance with AMS 3894 and thefollowing:5.1 Exterior package marking shall indicate storage temperature of “-18C (0F),maximum“.6. ACKNOWLEDGMENT: See AMS 3894.7. REJECTIONS: See

15、AMS 3894.8. NOTES: See AMS 3894.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE - 4 - AMS 3894/5B AMS 3894/5BCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-