SAE AMS 3357G-1991 Rubber Silicone (VMQ) Lubricating Oil and Compression Set Resistant 65 - 75《65-75耐润滑油及耐压缩变形的硅酮橡胶(VMQ)》.pdf

《SAE AMS 3357G-1991 Rubber Silicone (VMQ) Lubricating Oil and Compression Set Resistant 65 - 75《65-75耐润滑油及耐压缩变形的硅酮橡胶(VMQ)》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 3357G-1991 Rubber Silicone (VMQ) Lubricating Oil and Compression Set Resistant 65 - 75《65-75耐润滑油及耐压缩变形的硅酮橡胶(VMQ)》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE MATERIAL SPECIFICATION RUBBER, SILICONE (VMQ) Lubricating Oil and Compression Set Resistant 65 - 75 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary,

2、and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written

3、comments and suggestions. Copyright 2003 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission

4、 of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org AMS 3357G Issued FEB 1956 Revised JAN 1991 Reaffirmed NOV 2003 Superseding AMS 3357F 1. SCOPE: 1.1 Form: This speci

5、fication covers a silicone (VMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. 1.2 Application: Primarily for parts required to operate or seal from -55 to + 230C (-67 to +446 F), compounded specially for articraft piston engine oil resistance and low compression set. Si

6、licone elastomer is resistant to deterioration by weathering and by high-aniline-point petroleum-base oils normally suitable for use in contact with gasoline or aromatic fuels and low-aniline-point petroleum-base fluids due to excessive swelling of the elastomer. 1.3 Safety - Hazardous Materials: Wh

7、ile the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involve in such use. It is the sole responsibility of the user to ensure familiarity with the

8、 safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved. 2. APPLICABLE DOCUMENTS: The following publications form a part of this specification to the extent herein. The latest issue of SAE publications sha

9、ll apply. The applicable issue of other publications shall be the issue in effect on the date of the purchase order. AMS 3357G SAE AMS 3357G - 2 - 2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001. 2.1.1 Aerospace Material Specifications: AMS 2279 Tolerance,

10、 Rubber products MAM 2279 Tolerances, Metric, Rubber Products AMS 2810 Identification and Packaging, Elastomeric Products 2.2 ASTM Publications: Available from ASTM, 1916 Race Street, Philadelphia, PA 19103-1187. ASTM D 297 Rubber Products - Chemical Analysis ASTM D 395 Rubber Property - Compression

11、 Set ASTM D 412 Rubber Properties in Tension ASTM D 471 Rubber Property - Effect of Liquids ASTM D 573 Rubber - Deterioration in an Air Oven ASTM D 624 Rubber Property - Tear Resistance ASTM D 797 Rubber Property - Youngs Modulus at Normal and Subnormal Temperatures ASTM D 2137 Rubber Property - Bri

12、ttleness Point of Flexible Polymers and Coated Fabrics ASTM D 2240 Rubber Property - Durometer Hardness 3. TECHNICAL REQUIREMENTS: 3.1 Material: Shall be a compound, based on a silicone (VMQ) rubber, suitably cured to produce a product meeting the requirements of 3.2. 3.2 Properties: The product sha

13、ll conform to the following requirements; tests shall be performed on the product supplied and in accordance with specified ASTM methods, Insofar as practicable: 3.2.1 As Received: 3.2.1.1 Hardness, Durometer “A“ ASTM D 2240 or equivalent 70 5 3.2.1.2 Tensile Strength, minimum 800 psi ASTM D 412, Di

14、e B or C (5.52 MPa) 3.2.1.3 Elongation, minimum 150% ASTM D 412, Die B or C AMS 3357G SAE AMS 3357G - 3 - 3.2.1.4 Tensile Stress at 50% 200 psi ASTM D 412, Die B or C Elongation, minimum (1.39 MPa) 3.2.1.5 Tear Strength, minimum 60 pounds ASTM D 624, Die B force per inch (10.5 kN/m) 3.2.1.6 Specific

15、 Gravity Preproduction ASTM D 297 Value 0.03 3.2.2 Petroleum Lubricating Oil Resistance: ASTM D 471 (Immediate Deteriorated Properties) Medium: ASTM Oil No. 1 Temperature: 175C 3 3.2.2.1 Hardness Change, Durometer (347F 5) “A“ or equivalent -10 to +5 Time: 70 hours 0.5 3.2.2.2 Tensile Strength Chang

16、e, maximum -20% 3.2.2.3 Elongation Change, maximum -15% 3.2.2.4 Volume Change, maximum 0 to + 15% 3.2.2.5 Decomposition None 3.2.2.6 Surface Tackiness None 3.2.3 Dry Heat Resistance: ASTM D 573 Temperature: 225C 3 (437F 5) 3.2.3.1 Hardness Change, maximum Time: 22 hours 0.5 “A“ or equivalent -5 to +

17、10 3.2.3.2 Tensile Strength Change, maximum -15% 3.2.3.3 Elongation Change, maximum -25% 3.2.4 Compression Set: ASTM D 395, Method B Temperature: 175C 3 3.2.4.1 Percent of Original (347F 5) Deflection, maximum 35 Time: 22 hours 0.5 3.2.5 Low Temperature Resistance: AMS 3357G SAE AMS 3357G - 4 - 3.2.

18、5.1 Brittleness Pass ASTM D 2137, Method A Temperature: -65C 3 (-85F 0.5) 3.2.5.2 Youngs Modulus, maximum 10,000 ASTM D 797 (See 8.2) (68.9 MPa) Temperature: -50C 3 (-58F 5) Time: 5 hours 0.2 3.2.6 Weathering: The product shall have weather resistance acceptable to purchaser, determined by a procedu

19、re agreed upon by purchaser and vendor. 3.2.7 Corrosion: The product shall not have a corrosive effect on other materials when exposed to conditions normally encountered in service, determined by a procedure agreed upon by purchaser and vendor. Discoloration of metal shall not be considered objectio

20、nable. 3.3 Quality: The product, as received by purchaser, shall be uniform in quality and condition, smooth, as free from foreign materials as commercially practicable, and free from imperfections detrimental to usage of the product. 3.4 Tolerances: Shall conform to AMS 2279 or MAM 2279. 4. QUALITY

21、 ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of the product shall supply all samples for vendors tests and shall be responsible for performing all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that th

22、e product conforms to the requirements of this specification. AMS 3357G SAE AMS 3357G - 5 - 4.2 Classification of Tests: 4.2.1 Acceptance Tests: Tests for the following requirements are acceptance tests and shall be performed on each lot: Requirement Paragraph Reference Hardness, as received 3.2.1.1

23、 Tensile Strength, as received 3.2.1.2 Elongation, as received 3.2.1.3 Specific Gravity 3.2.1.6 Petroleum Lubricating Oil Resistance 3.2.2 Compression Set 3.2.4 4.2.2 Preproduction Tests: Tests for all technical requirements are preproduction tests and shall be performed prior to or on the initial s

24、hipment of the product to a purchaser, when a change in ingredients and/or processing requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be required. 4.2.2.1 For direct U.S. Military procurement, substantiating test data and, when requested, preproduction test material

25、 shall be submitted to the cognizant agency as directed by the procuring activity, contracting officer, or request for procurement. 4.3 Sampling and Testing: Shall be as follows: 4.3.1 For Acceptance Tests: Sufficient product shall be taken at random from each lot to perform all required tests. The

26、number of determinations for each requirement shall be as specified in the applicable test procedure if not specified therein, not less than three. 4.3.1.1 If specimens cannot be prepared from the product, ASTM test specimens prepared from the same batch and state of cure shall be used. When the pro

27、duct supplied is an extrusion of such shape that suitable test specimens cannot be cut from the product, a separate flat strip test sample from the same production lot shall be supplied upon request. This strip shall be prepared from tubing 1.000 inch 0.063 (25.40 mm 1.60) in OD by 0.075 inch 0.008

28、(1.90 mm 0.20) in wall thickness, mechanically slit and flattened into a strip while being extruded, and cured in the same manner as production product. When the product is a molded shape from which test specimens cannot be cut, a slab 6 inches (152 mm) square by 0.075 inch 0.008 (1.90 mm 0.020) thi

29、ck molded from the same batch of compound shall be supplied upon request. 4.3.1.2 A lot shall be all product from the same batch of compound processed in one continuous run and presented for vendors inspection at one time. An inspection lot shall not exceed 500 pounds (227 kg) and may be packaged in

30、 smaller quantities and delivered under the basic lot approval provided lot identification is maintained. AMS 3357G SAE AMS 3357G - 6 - 4.3.1.3 A batch shall be the quantity of compound run through a mill or mixer at one time. 4.3.1.4 When a statistical sampling plan has been agreed upon by purchase

31、r and vendor, sampling shall be in accordance with such plan in lieu of sampling as in 4.3.1 and the report of 4.5 shall state that such plan was used. 4.3.2 For Preproduction Tests: As agreed upon by purchaser and vendor. 4.4 Approval: 4.4.1 Sample product shall be approved by purchaser before prod

32、uct for production use is supplied, unless such approval be waived by purchaser. Results of tests on production product shall be essentially equivalent to those on the approved sample. 4.4.2 Vendor shall use ingredients, manufacturing procedures, processes, and methods of inspection on production pr

33、oduct which are essentially the same as those used on the approved sample product. If necessary to make any change in ingredients, in type of equipment for processing, or in manufacturing procedures, vendor shall submit for reapproval a statement of the proposed changes in ingredients and/or process

34、ing and, when requested, sample product. Production product made by the revised procedure shall not be shipped prior to receipt of reapproval. 4.5 Reports: The vendor of the product shall furnish with each shipment a report showing the results of tests to determine conformance to the acceptance test

35、 requirements and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, lot number, AMS 3357 G, vendors compound number, form and size or part number, and quantity. 4.6 Resampling and Retesting: If any specimen used in the above t

36、ests fails to meet the specified requirements, disposition of the product may be based on the results of testing three additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be cause for rejection of the product represen

37、ted. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY: 5.1 Identification and Packaging: Shall be in accordance with AMS 2810. 6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. AMS

38、3357G SAE AMS 3357G - 7 - 7. REJECTIONS: Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES: 8.1 Marginal Indicia: The phi () symbol is used to indicate technical changes from the previous issue of this specification. 8.2

39、 The test for Youngs Modulus is not normally required, but it is intended to be used as a referee test in case of disagreement on the results of the brittleness test. 8.3 Dimensions and properties in inch/pound units and the Celsius temperatures are primary; dimensions and properties in SI units and

40、 the Fahrenheit temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 For direct U.S. Military procurement, purchase documents should specify not less than the following: Title, number, and date of this specification Form and size or p

41、art number of product desired Quantity of product desired Acceptance standards and test methods for weather resistance (See 3.2.6) and corrosion (See 3.2.7) Level A packaging, if required (See AMS 2810). 8.5 Similar Specifications: Federal ZZ-R-765 is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. 8.6 Products meeting the requirements of this specification have been classified under Federal Supply Classification (FSC) 9320. THIS SPECIFICATION IS UNDER THE JURISDICTION OF AMS COMMITTEE “CE“.