SAE AMS 3050-2017 Performance Specification Anti-Seize Thread Compound High Temperature.pdf
《SAE AMS 3050-2017 Performance Specification Anti-Seize Thread Compound High Temperature.pdf》由会员分享,可在线阅读,更多相关《SAE AMS 3050-2017 Performance Specification Anti-Seize Thread Compound High Temperature.pdf(11页珍藏版)》请在麦多课文档分享上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS3050 AEROSPACE MATERIAL SPECIFICATION AMS3050 Issued 2017-12 Performance Specification Anti-
5、Seize Thread Compound, High Temperature RATIONALE This document has been revised to distinguish this foundation specification (AMS3050) and the associated category specifications (AMS3050/1 through AMS3050/9) and to classify different anti-seize greases conforming to this specification by the type o
6、f anti-seize additive. The category specifications have been added to the Applicable Documents section. The specification is a direct copy from MIL-PRF-907F 17 November 2004, except that it is intended to be used (by slash sheet designation) to exclude anti-seize materials not required on commercial
7、 aircraft, aircraft engines, engine pylons and aircraft components. All material referring to Mil Supply and usage; Contacts and addresses have been removed as not required for SAE purposes. No importance should be given to this type of material for future balloting of this specification. SAE INTERN
8、ATIONAL AMS3050 Page 2 of 11 TABLE OF CONTENTS 1. SCOPE 3 1.1 Form 3 1.1.1 Foundation and Category Specifications 3 2. APPLICABLE DOCUMENTS 3 2.1 General 3 2.2 Government Publications 3 2.2.1 Specifications, Standards and Handbooks . 3 2.3 Non-Government Publications 4 2.4 Order of Precedence . 4 3.
9、 REQUIREMENTS . 5 3.1 Qualification 5 3.2 Material 5 3.3 Corrosion on Copper . 5 3.4 Toxicity 5 3.5 Homogeneity . 5 3.6 Oil Separation . 5 3.7 Storage Stability 5 3.8 Performance 5 4. VERIFICATION . 5 4.1 Classification of Inspections 5 4.2 Qualification Inspection . 6 4.3 Conformance Inspection . 6
10、 4.3.1 Lot . 6 4.3.2 Examination of Filled Containers 6 4.3.3 Sample Material for Testing 6 4.3.4 Sampling for Production Check Tests . 6 4.4 Tests 7 4.4.1 Test Procedures 7 4.4.2 Performance Tests 7 4.4.3 Storage Stability 9 5. QUALITY ASSURANCE PROVISIONS 9 5.1 Responsibility for Inspection . 9 5.
11、2 Acceptance Tests 9 5.2.1 Batch . 9 5.2.2 Random Sampling . 9 5.2.3 Report 9 5.2.4 Report Contents 9 5.3 Change Management 9 6. PREPARATION FOR DELIVERY . 9 6.1 Packaging . 9 6.2 Identification 10 7. ACKNOWLEDGMENT 10 8. REJECTIONS . 10 9. NOTES 10 9.1 Revision Indicator 10 Figure 1 Test fixture 11
12、 Table 1 Test methods 7 SAE INTERNATIONAL AMS3050 Page 3 of 11 1. SCOPE 1.1 Form This foundation specification (AMS3050) and its associated category specifications (AMS3050/1 through AMS3050/9) cover anti-seize compounds for use on threads of nuts, studs, bolts, and other mating surfaces, including
13、those of superheated steam installations, at temperatures up to 1050 F (566 C). Compounds containing PTFE are limited to 600 F/315 C maximum. Materials for nuts, studs, bolts and other mating surfaces include, but are not limited to Steel, Nickel alloys, Stainless Steel, Silver coated materials. 1.1
14、.1 Foundation and Category Specifications This foundation specification establishes the requirements for all anti-seize compounds conforming to this specification. The individual Category specifications establish the requirements by separate anti-seize additives. Synthetic fluids and lithium complex
15、 soap thickeners are typically part of greases of this type, but other base fluids and thickeners may be acceptable. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplie
16、r may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 General The documents listed in this section are
17、 specified in Sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautio
18、ned that they must meet all specified requirements of documents cited in Sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government Publications 2.2.1 Specifications, Standards and Handbooks The following specifications, standards, and handbooks form a part of this doc
19、ument to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-907 MIL-PRF-680 Degreasing Solvent MIL-DTL-1222 Studs, Bolts, Hex Cap Screws and Nuts (Copies of these documen
20、ts are available at http:/quicksearch.dla.mil.) FEDERAL STANDARDS FED-STD-791 Lubricants, Liquid Fuels and Related Products; Methods of Testing (Copies of these documents are available at http:/quicksearch.dla.mil.) SAE INTERNATIONAL AMS3050 Page 4 of 11 2.3 Non-Government Publications The following
21、 documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. ASTM INTERNATIONAL ASTM A109 Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled. (DOD ad
22、opted) ASTM A193 Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service. (DOD adopted) ASTM A194 Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both. (DoD adopted) ASTM A515 Standar
23、d Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate and Higher-Temperature Service. (DOD adopted) (Copies of these documents are available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.) SAE AMS
24、3050 Performance Specification Anti-Seize Thread Compound, High Temperature AMS3050/1 Performance Specification Anti-Seize Thread Compound, High Temperature - Copper Only AMS3050/2 Performance Specification Anti-Seize Thread Compound, High Temperature - Aluminum Only AMS3050/3 Performance Specificat
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAMS30502017PERFORMANCESPECIFICATIONANTISEIZETHREADCOMPOUNDHIGHTEMPERATUREPDF

链接地址:http://www.mydoc123.com/p-1020795.html