SAE AMS 3045E-2008 Magnetic Particles Fluorescent Wet Method Oil Vehicle Ready-to-Use《即用型以油为媒介物的荧光磁性粒子用湿法》.pdf

《SAE AMS 3045E-2008 Magnetic Particles Fluorescent Wet Method Oil Vehicle Ready-to-Use《即用型以油为媒介物的荧光磁性粒子用湿法》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 3045E-2008 Magnetic Particles Fluorescent Wet Method Oil Vehicle Ready-to-Use《即用型以油为媒介物的荧光磁性粒子用湿法》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE MATERIAL SPECIFICATION AMS3045 REV. E Issued 1974-03 Revised 2008-11 Reaffirmed 2014-08 Superseding AMS3045D Magnetic Particles, Fluorescent Wet Method, Oil Vehicle, Ready-to-Use RATIONALE AMS3045E has been reaffirmed to comply with the SAE five year review policy. _ SAE Technical Standard

2、s Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole respon

3、sibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this publication may be reprod

4、uced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724

5、-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS3045E 1. SCOPE 1.1 Form This specification covers fluorescent magnetic particles in the form of a mixe

6、d, ready-to-use suspension in an odorless inspection oil vehicle. 1.2 Application These particles have been used typically as the inspection medium in a wet method, magnetic inspection system as defined in ASTM E 1444, but usage is not limited to such application. 1.3 Safety - Hazardous Materials Wh

7、ile the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure familiarity with th

8、e safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the

9、extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. SAE INTERNATIONA

10、L AMS3045E Page 2 of 5 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2641 Vehicle, Magnetic Particle Inspection, Petroleum Base AMS3044 Magnetic Partic

11、les, Fluorescent, Wet Method, Dry Powder AS5282 Tool Steel Ring for Magnetic Particle Inspection 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM D 1966 Test Method for Foots in Raw

12、Linseed Oil, (Gravimetric Method) ASTM E 1444 Magnetic Particle Examination 3. TECHNICAL REQUIREMENTS 3.1 Material The product shall be composed of durable fluorescent magnetic particles, suitable for long time use, which have been dyed or otherwise treated to attain the fluorescent color specified.

13、 The particles shall be supplied ready-to-use, mixed in the proper proportion with an inspection vehicle. 3.1.1 Fluorescent particles shall conform to AMS3044. 3.1.2 Magnetic particle inspection vehicle shall conform to AMS2641. 3.2 Storage Life The product shall meet the requirements of 3.3 when te

14、sted at any time up to 12 months from date of manufacture. 3.3 Properties The product shall conform to the following requirements; tests shall be performed, on the product supplied, in accordance with specified test methods: 3.3.1 Contamination The product shall show no evidence of foreign matter, a

15、gglomeration, or scum, determined by visual examination of the suspension at the following times: 3.3.1.1 During preparation of the test suspension as in 4.3.3. 3.3.1.2 After mixing the test suspension, allowing it to stand for not less than 30 minutes, and agitating it slightly. 3.3.1.3 During test

16、s to determine conformance with other characteristics of the product. 3.3.2 Concentration The concentration of magnetic particles in the vehicle shall be 0.10 to 0.40 mL of fluorescent particles in 100 mL of suspension, determined by mixing the test suspension thoroughly, filling a 100 mL calibrated

17、 centrifuge tube as specified in ASTM D 1966, allowing it to stand undisturbed for not less than 30 minutes, and reading, on the calibrated tube, the volume of particles settled from the suspension. SAE INTERNATIONAL AMS3045E Page 3 of 5 3.3.3 Sensitivity The product shall provide indications of at

18、least the first seven holes of the test ring specimen of 4.4 when tested as follows: 3.3.3.1 Place the ring on a 1-inch (25-mm) diameter copper bar and circularly magnetizing the ring in a standard magnetic particle inspection unit by passing 2500 amperes of direct current through the copper bar imm

19、ediately before flooding the ring with the agitated test suspension that has passed the contamination (3.3.1) and concentration (3.3.2) tests. Examine the ring in a darkened environment under ultraviolet light with a minimum UV-A intensity of 1000 W/cm2at the inspection surface. Visible light shall

20、not exceed 2 foot-candles (20 lx) at the inspection surface. 3.3.3.2 Flaw-to-Background Test Obtain a test part, or prepare a test specimen, containing flaws of the size expected to be found in production inspection. The surface finish of the test specimen shall be representative of production parts

21、. Magnetize and flood the specimen as specified in 3.3.3.1, using a sample of agitated test suspension that has passed the contamination (3.2.1) and concentration (3.3.2) tests. View the flaw indications in a darkened area under backlight as defined in 3.3.3.1. Indications shall be sharp and distinc

22、t. Background fluorescence around the flaws shall be of a level which will neither obscure the flaw indications nor cause difficulty in flaw detection. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The manufacturer of the product shall supply all samples for manufacturers tests a

23、nd shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that product conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance Tests All technical requirements,

24、 except storage life (3.2), are acceptance tests and shall be performed on each lot. 4.2.2 Preproduction Tests All technical requirements are preproduction tests and shall be performed prior to or on the initial shipment of the product to a purchaser, when a change in ingredients and/ or processing

25、requires reapproval as in 4.4.2, and when a purchaser deems confirmatory testing to be required. 4.3 Sampling and Testing Shall be as follows: 4.3.1 Acceptance Tests Sufficient product shall be taken at random from each lot to perform all required tests. The number of determinations for each require

26、ment shall be as specified in the applicable test procedure or, if not specified therein, not less than three. 4.3.1.1 Lot A lot shall be all product produced in a single production run from the same batches of raw materials under the same fixed conditions and presented for manufacturers inspection

27、at one time. SAE INTERNATIONAL AMS3045E Page 4 of 5 4.3.1.2 A statistical sampling plan, acceptable to purchaser, may be used in lieu of sampling as in 4.3.1. 4.3.2 For Preproduction Tests As agreed upon by purchaser and vendor. 4.3.3 Sample Preparation The product to be sampled shall be mixed thoro

28、ughly for not less than 30 minutes and a sample of at least 1 gallon (3.8 L) of suspension drawn off while being stirred. 4.3.4 Tool Steel Test Ring Shall be in accordance with AS5282. 4.4 Approval 4.4.1 Sample product shall be approved by purchaser before product for production use is supplied, unl

29、ess such approval be waived by purchaser. Results of tests on production product shall be equivalent to those on the approved sample. 4.4.2 Manufacturer shall use ingredients, manufacturing procedures, processes, and methods of inspection on production product that are the same as those used on the

30、approved sample. If necessary to make any changes in ingredients, processing techniques, or manufacturing procedures, manufacturer shall submit for reapproval a statement of the proposed changes in ingredients and/or processing and, when requested, sample product. Production product shall not be shi

31、pped prior to receipt of reapproval. 4.5 Reports The vendor of the product shall furnish with each shipment a report stating that the product conforms to all technical requirements. This report shall include the purchase order number, lot number, AMS3045E, manufacturers material designation, lot num

32、ber, and date of manufacture. 4.6 Resampling and Retesting If any sample used in the above tests fails to meet specified requirements, disposition of the product may be based on the results of testing three additional samples for each original nonconforming sample. Failure of any retest sample to me

33、et specified requirements shall be cause for rejection of the product represented. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY 5.1 Packaging and Identification 5.1.1 The product shall be packaged in containers of a type and size acceptable to purchaser. 5.1.2 A lot of magneti

34、c particles may be packaged in small quantities and delivered under the basic lot approval provided lot identification is maintained. SAE INTERNATIONAL AMS3045E Page 5 of 5 5.1.3 Each container shall be identified with a durable label, that is legible on receipt, with not less than the following inf

35、ormation: MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, OIL VEHICLE, READY-TO-USE AMS3045E _ MANUFACTURERS IDENTIFICATION_ DATE OF MANUFACTURE _ * _ LOT NUMBER _ QUANTITY _ MANUFACTURERS INSTRUCTIONS FOR USE _ * _ APPROPRIATE WARNINGS OR PRECAUTIONARY NOTICES _ * May be included in manufacturers iden

36、tification or lot number. * May be on a separate sheet. 5.1.4 Individual packages or containers shall be packed in an exterior shipping container capable of protecting the product, during shipment and storage, against damage from exposure to moisture, weather, or any other normal hazard. 5.1.5 Conta

37、iners of the product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall

38、 mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar ( l ) located in the l

39、eft margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Chang

40、e bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions in inch/pound units and the Fahrenheit temperatures are primary; dimensions in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Purchase orders should specify not less than the following: AMS3045E Size and type of containers desired (See 5.1.1) Quantity of product desired. PREPARED BY AMS COMMITTEE “K”