SAE AMS 2585A-2013 Shot Peening Media Ultrasonically Activated《超声波激活喷丸加工介质》.pdf
《SAE AMS 2585A-2013 Shot Peening Media Ultrasonically Activated《超声波激活喷丸加工介质》.pdf》由会员分享,可在线阅读,更多相关《SAE AMS 2585A-2013 Shot Peening Media Ultrasonically Activated《超声波激活喷丸加工介质》.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.Copyright 2013 SAE InternationalAll rights reserved. No part of this publication may b
3、e reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (outside USA)Fax
4、: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS2585AAEROSPACEMATERIALSPECIFICATIONAMS2585 REV. AIssued 2010-05Revised 2013-07Superseding AMS2585Shot
5、Peening Media, Ultrasonically ActivatedRATIONALEThis revision includes ceramic media and additional media sizes to address user requirements.1. SCOPEThe complete requirements for procuring the product shall consist of this document and the latest Issue of the basic specification, AMS2431.1.1 Applica
6、tionPeening balls conforming to this specification are typically intended for use in ultrasonically activated shot peening of metal surfaces to impart compressive stresses to these surfaces thereby increasing resistance to fatigue and stress-corrosion cracking. These balls can also be used in the pe
7、en forming process.2. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. Wh
8、en the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 72
9、4-776-4970 (outside USA), www.sae.org.AMS2431 Peening Media, General Requirements2.2 ASTM PublicationsAvailable from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959,Tel: 610-832-9585, www.astm.org.ASTM A 751 Standard Test Methods, Practices, and Terminology
10、 for Chemical Analysis of Steel ProductsASTM E 384 Standard Test Method for Knoop and Vickers Hardness of Materials ASTM E140 Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Knoop Hardness, and Scleroscope HardnessSAE AMS2585A
11、Page 2 of 62.3 ANSI PublicationsAvailable from American National Standards Institute (ANSI), 25 West 43rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org.ANSI/ABMA/ISO 3290 Rolling bearings - Balls - Dimensions and Tolerances 2.4 DIN PublicationsAvailable from DIN Deutsches Institut
12、 fr Normung e. V., Burggrafenstrae, 6, 10787, Berlin, Germany or www.DIN.de.DIN 5401 Rolling bearings - Balls for rolling bearings and general industrial use 2.5 BNAE PublicationsAvailable from BNAE, Technopolis 54, 199, rue Jean Jacques ROUSSEAU, 92138 Issy les Moulineaux cedex, France or www.BNAE.
13、asso.fr.BNAE NFL 06-834 Metallic parts Inducement Compressive Surface Stresses Tungsten Carbide Spherical Beads2.6 ISO PublicationsAvailable from International Organization for Standarization, 1, rue de Varembe, Case postale 56, CH-1211 Geneva 20, Switzerland, Tel: +41-22-749-01-11, www.iso.org.ISO
14、3290 Rolling Bearings - Balls - Dimensions and Tolerances3. TECHNICAL REQUIREMENTS3.1 Peening balls shall conform to AMS2431 and the requirements specified herein.3.2 Composition and properties3.2.1 Chemical composition of peening balls shall conform to Table 1 or an alternative composition approved
15、 by the cognizant engineering organization.TABLE 1 COMMON PEENING BALL MATERIALSMaterial Alloy AFNOR / ISO / DIN equivalent HardnessSteel 52100 100C6 60-67 HRCM50 60-66 HRC1010/1015 XC10/XC15 60-66 HRC1055/1065/1085 60-66 HRCStainless Steel440C Z100CD17 58-65 HRC304 Z7CN18-09 25-39 HRC304L Z2CN18-10
16、 25-39 HRC316 Z6CND17-12 25-39 HRC316L Z2CND17-12 25-39 HRCTungsten Carbide n/a BNAE NFL 06-834 1400-1800 HVCeramic High Density ZrO2 +HfO2 + Y2O31100-1300 HVSAE AMS2585A Page 3 of 63.2.2 The percentage variation by weight ranges of the main constituents of ceramic ball shall conform to requirements
17、 in Table 2:TABLE 2 CERAMIC BALLS COMPOSITIONConstituent min maxZirconium Oxide +Hafnium Oxide90 95Yttrium Oxide 3 7Others 3Note: Approved alternative shall conform to an AISI, SAE, ASTM, DIN, or ISO standard.3.2.3 The surface finish, the shape and tolerances for steel, stainless steel and tungsten
18、carbide media shall conform to grade of ANSI/ABMA/ISO 3290 or ISO 3290 or DIN 5401 defined in Table 3.TABLE 3 REQUIRED GRADES OF PEENING BALLSStandard GradeAISI/ABMA/ISO 3290 up to 200ISO 3290 up to 200DIN 5401 up to class III3.2.4 Ceramic media shall be predominantly spherical in shape. 90% of medi
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAMS2585A2013SHOTPEENINGMEDIAULTRASONICALLYACTIVATED 超声波 激活 加工 介质 PDF
链接地址:http://www.mydoc123.com/p-1020691.html