SAE AMS 2370L-2016 Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Wrought Products and Forging Stock.pdf

《SAE AMS 2370L-2016 Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Wrought Products and Forging Stock.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 2370L-2016 Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Wrought Products and Forging Stock.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、_ 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSX EOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJL neering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, LVWKHVROHUHVSRQ

2、VLELOLWRIWKHXVHU SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced,

3、stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0

4、790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS2370L AEROSPACE MATERIAL SPECIFICATION AMS2370 REV. L Issued 1969-05 Revised 2016-06 Superseding AMS2370K Qu

5、ality Assurance Sampling and Testing Carbon and Low-Alloy Steel Wrought Products and Forging Stock RATIONALE AMS2370L results from a Five Year Review and update of this specification that adds a minimum number of samples/specimens for testing. 1. SCOPE This specification covers quality assurance sam

6、pling and testing procedures used to determine conformance to applicable material specification requirements of wrought carbon and low-alloy steel products and of forging stock. 1.1 Attributes included in detail herein are: Composition, tensile properties, macrostructure, and micro-inclusion rating.

7、 Other requirements are included in Table 2. 1.2 Quality assurance sampling and testing procedures for forgings are covered in AMS2372. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified

8、herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available fr

9、om SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2372 Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Forgings ARP1917 Clarification of Terms Used in Aerospace Metals

10、 Specifications SAE INTERNATIONAL AMS2370L Page 2 of 10 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM E8/E8M Tension Testing of Metallic Materials 3. TECHNICAL REQUIREMENTS 3.1 Ge

11、neral 3.1.1 Omission from this specification of confirmatory tests of certain material properties or attributes controlled by the applicable material specification does not relieve the vendor of responsibility for furnishing products that conform in all respects to the applicable material specificat

12、ion. 3.1.2 In event of conflict between requirements specified herein and requirements of a particular material specification, requirements of the material specification shall take precedence. 3.2 Responsibility for Tests The vendor of the product shall supply all samples for vendors tests and shall

13、 be responsible for the performance of all required tests. Results of such tests shall be reported to the purchaser as required by the applicable material specification. 3.3 Detail Requirements 3.3.1 Lot A lot shall be as defined in 3.3.1.1 or 3.3.1.2; the applicable definition being as specified in

14、 Table 2 for the type of test and type of product being tested. 3.3.1.1 A lot shall be restricted to the product of a single heat. 3.3.1.1.1 A heat shall be all steel melted in a single furnace charge. For consumable electrode remelted steel, a heat shall be all consumable electrode remelted ingots

15、processed from steel originally melted as a single furnace charge. 3.3.1.2 A lot shall be a mill form of one shape, condition, and nominal cross-sectional dimensions from a single heat, processed in accordance with 3.3.1.2.1 or 3.3.1.2.2. 3.3.1.2.1 Sequentially heat treated during a 24-hour period i

16、n a continuous furnace with no interruption in operations and no change in furnace temperature, charge rate, or racking pattern. 3.3.1.2.1.1 The nominal cross-sectional dimension restriction may be disregarded when multiple sizes are heat treated in a single batch or during an 8-hour period in a con

17、tinuous furnace operating at a constant speed. In such cases, tensile and macrostructure testing shall be performed on the size having the greatest equivalent round cross-section. The equivalent round cross-section shall be determined by multiplying wall thickness of tubing and thickness or diameter

18、 of solids by the shape factors shown in Table 1. Table 1 - Shape factors Product Shape Factor Tubing 2.0 Rounds 1.0 Hexagons 1.1 Squares 1.25 Flats 1.50 SAE INTERNATIONAL AMS2370L Page 3 of 10 3.3.1.2.2 Sequentially heat treated during a 48-hour period in one or a series of batch-type furnace loads

19、 provided the loads are processed in the same furnace or same series of furnaces, and at the same power setting, set temperature, soak time, quench parameters, and racking pattern. 3.3.2 Sampling and Testing Shall be in accordance with Table 2 and as follows: 3.3.2.1 Composition 3.3.2.1.1 The report

20、ed composition of the steel subjected to a single melting operation shall be that of a sample taken immediately before or during the pouring of a heat. Analysis results of the sample shall be within the composition limits established by the material specification, excluding any consideration of prod

21、uct check analysis. 3.3.2.1.1.1 If the sample of 3.3.2.1.1 is lost, a new sample shall be taken from the semi-finished or finished product. 3.3.2.1.2 For remelted steels, analyses shall be obtained from the remelted ingot or product thereof in accordance with a sampling plan that will allow the repo

22、rted composition of the steel to conform to one of the following options: The average of all ingots in the remelted heat. The average of the ingots directly involved with the order. The average of samples representing the first and last usable metal poured from the heat. The analysis of each ingot i

23、nvolved with the order. 3.3.2.1.2.1 If an average for an element is reported, each analysis of the element shall fall within the compositional limits established by the material specification; each individual analysis may include the applicable product check analysis allowance, but no average shall

24、include analyses that are both above and below the compositional limits. 3.3.2.1.2.2 When the remelting method is vacuum-arc remelting and the applicable material specification establishes minimum values for carbon and/or manganese, these elements shall be determined and reported for each remelted i

25、ngot. 3.3.2.1.2.3 The heat analysis may be used for reporting the analyses of those elements governed only by a maximum in the material specification if the analysis is within the compositional limits and the element routinely decreases or remains constant during remelting. 3.3.2.1.2.4 Analyses of s

26、amples made prior to discard need not be reported. 3.3.2.2 Tensile Specimen Orientation, Location, and Size Tensile specimens conforming to ASTM E8/E8M shall be cut from the semi-finished or finished product in the direction indicated in the following paragraphs, and shall be cut from the locations

27、and to the sizes specified. The sample shall consist of one or more sections of the product selected to represent a specific location or locations with respect to the order of pouring of the selected ingot or ingots and with respect to the location within the ingot. 3.3.2.2.1 Sheet, Strip, and Plate

28、 3.3.2.2.1.1 Orientation Specimens shall be taken with the axis of the specimen perpendicular to the direction of rolling from widths 9 inches (229 mm) and over and parallel to the direction of rolling from widths under 9 inches (229 mm). When short-transverse tensile properties are specified in the

29、 applicable material specification, specimens shall be taken with the axis of the specimen parallel to the thickness direction of the product. SAE INTERNATIONAL AMS2370L Page 4 of 10 3.3.2.2.1.2 Location and Size 3.3.2.2.1.2.1 Longitudinal and Long-Transverse Specimens The standard inch (12.7 mm) wi

30、de rectangular specimen or pin-loaded tensile specimen with 2 inch (50.8 mm) gage length shall be used for sheet, strip, and plate 0.625 inch (15.88 mm) and under in nominal thickness. For plate 0.625 to 0.750 inch (15.88 to 19.05 mm), inclusive, in nominal thickness, either the standard inch (12.7

31、mm) wide rectangular specimen with 2 inch (50.8 mm) gage length or the standard inch (12.7 mm) round tensile specimen with 2 inch (50.8 mm) gage length or a smaller, round specimen proportional to the standard shall be used. For plate over 0.750 inch (19.05 mm) in nominal thickness, the standard inc

32、h (12.7 mm) round tensile specimen with 2 inch (50.8 mm) gage length or smaller, round specimen proportional to the standard shall be used. The tensile specimen shall be located midway between the faces of product 1- inches (38.1 mm) and under in nominal thickness and midway from center to surface f

33、or product over 1- inches (38.1 mm) in nominal thickness. 3.3.2.2.1.2.2 Short-Transverse Specimens For plate 2- inches (63.5 mm) and over in nominal thickness, subsize round tensile specimens, proportional to the standard, shall be used when thickness is insufficient to accommodate standard inch (12

34、.7 mm) round tensile specimens with 2 inch (50.8 mm) gage length. Short-transverse testing is not applicable for plate under 2- inches (63.5 mm) in nominal thickness. 3.3.2.2.2 Bar, Rod, and Wire 3.3.2.2.2.1 Orientation Specimens shall be taken with the axis of the specimen in the longitudinal direc

35、tion except that, when long-transverse tensile properties are specified in the applicable material specification, specimens shall be taken with the axis of the specimen perpendicular to the rolling or extruding direction. When short-transverse tensile properties are specified for rectangular bar in

36、the applicable material specification, specimens shall be taken with the axis of the specimen parallel to the thickness direction of the bar. 3.3.2.2.2.2 Location and Size 3.3.2.2.2.2.1 Longitudinal and Long-Transverse Specimens If the product size or shape makes it impractical to use full-section s

37、pecimens, the standard inch (12.7 mm) round tensile specimen with 2 inch (50.8 mm) gage length or a smaller, round specimen proportional to the standard, shall be used, except that for rectangular bar 0.625 inch (15.88 mm) and under in nominal thickness, the standard inch (12.7 mm) wide rectangular

38、specimen or pin-loaded tensile specimen with 2 inch (50.8 mm) gage length may be used. The tensile specimen shall be located at the center for product 1- inches (38.1 mm) and under in nominal diameter, thickness, or distance between flats and midway from center to surface for product over 1- inches

39、(38.1 mm) in nominal thickness. 3.3.2.2.2.2.2 Short-Transverse Specimens For bar 2- inches (63.5 mm) and over in nominal thickness, subsize round tensile specimens, proportional to the standard, shall be used when thickness is insufficient to accommodate standard inch (12.7 mm) round tensile specime

40、ns with 2 inch (50.8 mm) gage length. Short-transverse testing is not applicable for bar under 2- inches (63.5 mm) in nominal thickness. SAE INTERNATIONAL AMS2370L Page 5 of 10 3.3.2.2.3 Tubing 3.3.2.2.3.1 Orientation Specimens shall be taken with the axis of the specimen in the longitudinal directi

41、on except that, when long-transverse tensile properties of square or rectangular tubing are required by the applicable material specification, specimens shall be taken with the axis of the specimen perpendicular to the drawing or extruding direction. 3.3.2.2.3.2 Longitudinal Specimens Specimens from

42、 round and square tubing shall be the full section of the tubular product unless limitations of the testing machine preclude the use of such specimens. Snug-fitting metal plugs shall be inserted into the ends of tubular specimens to a sufficient depth to permit the jaws of the testing machine to gri

43、p the specimen properly without crushing. The plugs shall not extend into that portion of the specimen to be tested. Care shall be exercised to ensure that the load is applied axially. The length of full-section specimens shall be determined by the gage length specified for measuring elongation. For

44、 large-size tubing, or when it is not possible to test in full section, longitudinal specimens shall be obtained from strips cut from the tube. Either inch (12.7 mm) wide rectangular or subsize round tensile specimens, proportional to the standard, (for thick-wall tube) shall be machined from these

45、strips. Longitudinal strip-type tensile specimens from welded tubing shall not include weld bead. For thick-wall tubing for which subsize round tensile specimens are used, when the nominal wall thickness is under 1- inches (38.1 mm), specimens shall be taken midway between the inner and outer surfac

46、e of the tubing; when the nominal wall thickness is 1- inches (38.1 mm) and over, specimens shall be taken at one-quarter wall thickness, referencing from either OD or ID. 3.3.2.2.3.3 Long-Transverse Specimens Rectangular specimens or subsize round specimens, proportional to the standard, shall be u

47、sed for square or rectangular tubing. Rectangular or round tensile specimens of the largest possible dimensions, proportional to the standard, shall be used when standard size specimens cannot be obtained. For thick walled tubing, a round tensile specimen shall be taken midway between the inner and

48、outer surface of the tubing when the nominal wall thickness is under 1- inches (38.1 mm); when the nominal wall thickness is 1- inches (38.1 mm) and over, specimens shall be taken at one-quarter wall thickness, referencing from either OD or ID. 3.3.2.2.4 Shapes 3.3.2.2.4.1 Orientation Specimens shall be taken with the axis of the specimen in the longitudinal direction except that, when long-transverse tensile properties are specified in the applicable material specification, specimens shall be taken with