NFPA 70E-2015 Standard for Electrical Safety in the Workplace (Effective Date 7 29 2014 ALERT THIS STANDARD HAS BEEN MODIFIED BY A TIA OR ERRATA).pdf

《NFPA 70E-2015 Standard for Electrical Safety in the Workplace (Effective Date 7 29 2014 ALERT THIS STANDARD HAS BEEN MODIFIED BY A TIA OR ERRATA).pdf》由会员分享，可在线阅读，更多相关《NFPA 70E-2015 Standard for Electrical Safety in the Workplace (Effective Date 7 29 2014 ALERT THIS STANDARD HAS BEEN MODIFIED BY A TIA OR ERRATA).pdf（110页珍藏版）》请在麦多课文档分享上搜索。

1、NFPA 70EStandard for Electrical Safety in the Workplace 2015 Edition NFPA, 1 Batterymarch Park, Quincy, MA 02169-7471 An International Codes and Standards Organization 1/14ISBN: 978-145590893-6 (Print)ISBN: 978-145590926-1 (PDF)IMPORTANT NOTICES AND DISCLAIMERS CONCERNING NFPASTANDARDS NOTICE AND DI

2、SCLAIMER OF LIABILITY CONCERNING THE USE OF NFPA STANDARDSNFPAcodes, standards, recommended practices, and guides (“NFPA Standards”), of which the document contained herein is one, are developed through a consensus standards development process approved by the American National Standards Institute.

3、This process brings together volunteers representing varied viewpoints and interests to achieve consensus on fire and other safety issues. While the NFPA administers the process and establishes rules to promote fairness in the development of consensus, it does not independently test, evaluate, or ve

4、rify the accuracy of any information or the soundness of any judgments contained in NFPA Standards.The NFPA disclaims liability for any personal injury, property or other damages of any nature whatsoever, whether special, indirect, consequential or compensatory, directly or indirectly resulting from

5、 the publication, use of, or reliance on NFPA Standards. The NFPA also makes no guaranty or warranty as to the accuracy or completeness of any information published herein.In issuing and making NFPA Standards available, the NFPA is not undertaking to render professional or other services for or on b

6、ehalf of any person or entity. Nor is the NFPA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of re

7、asonable care in any given circumstances.The NFPA has no power, nor does it undertake, to police or enforce compliance with the contents of NFPA Standards. Nor does the NFPA list, certify, test, or inspect products, designs, or installations for compliance with this document. Any certification or ot

8、her statement of compliance with the requirements of this document shall not be attributable to the NFPA and is solely the responsibility of the certifier or maker of the statement.REMINDER: UPDATING OF NFPA STANDARDSUsers of NFPA codes, standards, recommended practices, and guides (“NFPA Standards”

9、) should be aware that NFPA Standards may be amended from time to time through the issuance of Tentative Interim Amendments or corrected by Errata. An official NFPA Standard at any point in time consists of the current edition of the document together with any Tentative Interim Amendment and any Err

10、ata then in effect.In order to determine whether an NFPA Standard has been amended through the issuance of Tentative Interim Amendments or corrected by Errata, visit the Document Information Pages on NFPAs website. The Document Information Pages provide up-to-date, document specific information incl

11、uding any issued Tentative Interim Amendments and Errata.To access the Document Information Page for a specific NFPA Standard, go to http:/www.nfpa.org/docinfo to choose from the list of NFPA Standards or use the search feature on the right to select the NFPA Standard number (e.g., NFPA 101). In add

12、ition to posting all existing Tentative Interim Amendments and Errata, the Document Information Page also includes the option to sign-up for an “Alert” feature to receive an email notification when new updates and other information are posted regarding the document.1/14IMPORTANT NOTICES AND DISCLAIM

13、ERS CONCERNING NFPASTANDARDS ADDITIONAL NOTICES AND DISCLAIMERSUpdating of NFPA Standards Users of NFPA codes, standards, recommended practices, and guides (“NFPA Standards”) should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from tim

14、e to time through the issuance of Tentative Interim Amendments or corrected by Errata. An official NFPA Standard at any point in time consists of the current edition of the document together with any Tentative Interim Amendments and any Errata then in effect. In order to determine whether a given do

15、cument is the current edition and whether it has been amended through the issuance of Tentative Interim Amendments or corrected through the issuance of Errata, consult appropriate NFPA publications such as the National Fire CodesSubscription Service, visit the NFPA website at www.nfpa.org, or contac

16、t the NFPA at the address listed below.Interpretations of NFPA StandardsA statement, written or oral, that is not processed in accordance with Section 6 of the Regulations Governing the Development of NFPA Standards shall not be considered the official position of NFPA or any of its Committees and s

17、hall not be considered to be, nor be relied upon as, a Formal Interpretation.PatentsThe NFPA does not take any position with respect to the validity of any patent rights referenced in, related to, or asserted in connection with an NFPA Standard. The users of NFPA Standards bear the sole responsibili

18、ty for determining the validity of any such patent rights, as well as the risk of infringement of such rights, and the NFPA disclaims liability for the infringement of any patent resulting from the use of or reliance on NFPA Standards.NFPA adheres to the policy of the American National Standards Ins

19、titute (ANSI) regarding the inclusion of patents in American National Standards (“the ANSI Patent Policy”), and hereby gives the following notice pursuant to that policy:NOTICE: The users attention is called to the possibility that compliance with an NFPA Standard may require use of an invention cov

20、ered by patent rights. NFPA takes no position as to the validity of any such patent rights or as to whether such patent rights constitute or include essential patent claims under the ANSI Patent Policy. If, in connection with the ANSI Patent Policy, a patent holder has filed a statement of willingne

21、ss to grant licenses under these rights on reasonable and nondiscriminatory terms and conditions to applicants desiring to obtain such a license, copies of such filed statements can be obtained, on request, from NFPA. For further information, contact the NFPA at the address listed below.Law and Regu

22、lationsUsers of NFPA Standards should consult applicable federal, state, and local laws and regulations. NFPA does not, by the publication of its codes, standards, recommended practices, and guides, intend to urge action that is not in compliance with applicable laws, and these documents may not be

23、construed as doing so.CopyrightsNFPA Standards are copyrighted. They are made available for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of safe practices and meth

24、ods. By making these documents available for use and adoption by public authorities and private users, the NFPA does not waive any rights in copyright to these documents.Use of NFPA Standards for regulatory purposes should be accomplished through adoption by reference. The term “adoption by referenc

25、e” means the citing of title, edition, and publishing information only. Any deletions, additions, and changes desired by the adopting authority should be noted separately in the adopting instrument. In order to assist NFPA in following the uses made of its documents, adopting authorities are request

26、ed to notify the NFPA (Attention: Secretary, Standards Council) in writing of such use. For technical assistance and questions concerning adoption of NFPA Standards, contact NFPA at the address below.For Further InformationAll questions or other communications relating to NFPA Standards and all requ

27、ests for information on NFPA procedures governing its codes and standards development process, including information on the procedures for requesting Formal Interpretations, for proposing Tentative Interim Amendments, and for proposing revisions to NFPA standards during regular revision cycles, shou

28、ld be sent to NFPA headquarters, addressed to the attention of the Secretary, Standards Council, NFPA, 1 Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101; email: stds_adminnfpa.orgFor more information about NFPA, visit the NFPA website at www.nfpa.org. All NFPA codes and standards can be view

29、ed at no cost at www.nfpa.org/freeaccess.Copyright 2014, National Fire Protection Association. All Rights ReservedNFPA 70EStandard forElectrical Safety in the Workplace2015 EditionThis edition of NFPA 70E, Standard for Electrical Safety in the Workplace, was prepared by theTechnical Committee on Ele

30、ctrical Safety in the Workplace and released by the Correlating Committeeon National Electrical Code. It was issued by the Standards Council on July 14, 2014, with an effectivedate of July 29, 2014, and supersedes all previous editions.A Tentative Interim Amendment (TIA) to 130.7(C)(10)(b)(1) and Ta

31、bles H.3(a) and (b) was issuedon August 14, 2014. For further information on tentative interim amendments, see Section 5 of theRegulations Governing the Development of NFPA Standards, available at http:/www.nfpa.org/regsThis edition of NFPA 70E was approved as an American National Standard on July 2

32、9, 2014.Foreword to NFPA 70EThe Standards Council of the National Fire Protection Association announced on January 7, 1976,the formal appointment of a new electrical standards development committee. Entitled the Committeeon Electrical Safety Requirements for Employee Workplaces, NFPA 70E, this new c

33、ommittee reportedto the Association through the Technical Correlating Committee on National Electrical Code. Thiscommittee was formed to assist OSHA in preparing electrical safety standards that would serve OSHAsneeds and that could be expeditiously promulgated through the provisions of Section 6(b)

34、 of theOccupational Safety and Health Act. OSHA found that in attempting to utilize the latest edition ofNFPA 70, National Electrical Code(NEC), it was confronted with the following problems:(1) Updating to a new edition of the NEC would have to be accomplished through the OSHA 6(b)procedures. OSHA

35、adopted the 1968 and then the 1971 NEC under Section 6(a) procedures of theOccupational Safety and Health Act of 1970. Today, however, OSHA can only adopt or modify astandard by the procedures of Section 6(b) of the OSHA Act, which provide for public notice,opportunity for public comment, and public

36、 hearings. The adoption of a new edition of the NEC bythese procedures would require extensive effort and application of resources by OSHA and others.Even so, going through the Section 6(b) procedures might result in requirements substantiallydifferent from those of the NEC, thereby creating the pro

37、blem of conflict between the OSHAstandard and other national and local standards.(2) The NEC is intended for use primarily by those who design, install, and inspect electrical installa-tions. OSHAs electrical regulations address employers and employees in their workplaces. Thetechnical content and c

38、omplexity of the NEC is extremely difficult for the average employer andemployee to understand.(3) Some of the detailed provisions within the NEC are not directly related to employee safety and,therefore, are of little value for OSHAs needs.(4) Requirements for electrical safety-related work practic

39、es and maintenance of the electrical systemconsidered critical to safety are not found in the NEC, which is essentially an electrical installationdocument. However, OSHA must also consider and develop these safety areas in its regulations.With these problem areas, it became apparent that a need exis

40、ted for a new standard, tailored tofulfill OSHAs responsibilities, that would still be fully consistent with the NEC.The foregoing issues led to the concept that a document be put together by a competent group,representing all interests, that would extract suitable portions from the NEC and from oth

41、er documentsapplicable to electrical safety. This concept and an offer of assistance was submitted in May 1975 to theAssistant Secretary of Labor for OSHA, who responded as follows: “The concept, procedures, andscope of the effort discussed with my staff for preparing the subject standard appear to

42、have great merit,and an apparent need exists for this proposed consensus document which OSHA could consider forNFPA 70E, Standard for Electrical Safety in the Workplace, NFPA, and National Fire Protection Association are registered trademarks of theNational Fire Protection Association, Quincy, Massa

43、chusetts, 02169.70E1promulgation under the provisions of Section 6(b) of the Act. OSHA does have an interest in this effort andbelieves the proposed standard would serve a useful purpose.” With this positive encouragement from OSHA, aproposal to prepare such a document was presented to the NFPA Elec

44、trical Section, which unanimously sup-ported a recommendation that the NEC Correlating Committee examine the feasibility of developing a documentto be used as a basis for evaluating electrical safety in the workplace. In keeping with the recommendation of theElectrical Section and Correlating Commit

45、tee, the Standards Council authorized the establishment of a committeeto carry out this examination.The committee found it feasible to develop a standard for electrical installations that would be compatiblewith the OSHA requirements for safety for the employee in locations covered by the NEC. The n

46、ew standard wasvisualized as consisting of four major parts: Part I, Installation Safety Requirements; Part II, Safety-Related WorkPractices; Part III, Safety-Related Maintenance Requirements; and Part IV, Safety Requirements for SpecialEquipment. Although desirable, it was not considered essential

47、for all of the parts to be completed before thestandard was published and made available. Each part is recognized as being an important aspect of electricalsafety in the workplace, but the parts are sufficiently independent of each other to permit their separate publica-tion. The new standard was na

48、med NFPA 70E, Standard for Electrical Safety Requirements for EmployeeWorkplaces. The first edition was published in 1979 and included only Part I.The second edition was published in 1981. It included Part I as originally published and a new Part II. In1983, the third edition included Part I and Par

49、t II as originally published and a new Part III. In 1988, the fourthedition was published with only minor revisions.The fifth edition, published in 1995, included major revisions to Part I, updating it to conform to the 1993edition of NFPA 70, National Electrical Code (NEC). In Part II of the fifth edition, the concepts of “limits ofapproach” and establishment of an “arc” were introduced. In 2000, the sixth edition included a complete Part Iupdate to the 1999 NEC, as well as a new Part IV. Part II continued to focus on establishing flash protectionboundaries and the us