1、*USACE / NAVFAC / AFCESA / NASA UFGS-07 31 13 (November 2011)-Preparing Activity: NAVFAC SupersedingUFGS-07 31 13 (May 2011)UFGS-07 31 13 (April 2006)UFGS-07311 (February 2003)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated October 2011*SECTION TABLE OF CONTENTSDIV
2、ISION 07 - THERMAL AND MOISTURE PROTECTIONSECTION 07 31 13ASPHALT SHINGLES11/11PART 1 GENERAL1.1 REFERENCES1.2 DEFINITIONS1.2.1 Top Lap1.2.2 Head Lap1.2.3 Exposure1.3 SUBMITTALS1.4 DELIVERY AND STORAGE1.5 WARRANTIES1.5.1 Manufacturers Warranty1.5.2 Contractors Warranty1.6 QUALITY ASSURANCE1.6.1 Loca
3、l/Regional Materials1.6.2 Recycled MaterialsPART 2 PRODUCTS2.1 MATERIALS2.1.1 Shingles2.1.2 Mineral-Surfaced Asphalt Roll Roofing2.1.3 Smooth-Surfaced Asphalt Roll Roofing2.1.4 Underlayment2.1.4.1 Leak Barrier Underlayment2.1.5 Self-Adhering Membrane2.1.6 Nails for Applying Shingles and Asphalt-Satu
4、rated Felt2.1.7 Asphalt Roof Cement2.1.8 Asphalt Primer2.1.9 Ventilators2.1.9.1 Nailable Plastic Shingle Over Type Ridge Vents2.1.9.2 Nailable Mesh Shingle Over Type Ridge VentsPART 3 EXECUTIONSECTION 07 31 13 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license
5、 from IHS-,-,-3.1 VERIFICATION OF CONDITIONS3.2 SURFACE PREPARATION3.3 APPLICATION3.3.1 Underlayment3.3.2 Drip Edges3.3.3 Starter Strip3.3.4 Shingle Courses3.3.5 Hips and Ridges3.3.6 Valleys3.3.6.1 Closed Cut Valleys3.3.6.2 Woven Valleys3.3.6.3 Open Roll Roofing Valleys3.3.6.4 Open Sheet Metal Valle
6、ys3.3.7 Flashing3.3.7.1 Eave Flashing3.3.7.2 Stepped Flashing3.3.7.3 Vent and Stack Flashing3.3.7.4 Chimney Flashing- End of Section Table of Contents -SECTION 07 31 13 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA /
7、NASA UFGS-07 31 13 (November 2011)-Preparing Activity: NAVFAC SupersedingUFGS-07 31 13 (May 2011)UFGS-07 31 13 (April 2006)UFGS-07311 (February 2003)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated October 2011*SECTION 07 31 13ASPHALT SHINGLES11/11*NOTE: This guide
8、specification covers the requirements for asphalt shingle roofing, surfaced with mineral granules, including roofing felt, ridge vents, underlayments, and flashings.Adhere to UFC 1-300-02 Unified Facilities Guide Specifications (UFGS) Format Standard when editing this guide specification or preparin
9、g new project specification sections. Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective project, wheth
10、er or not brackets are present.Comments, suggestions and recommended changes for this guide specification are welcome and should be submitted as a Criteria Change Request (CCR).*NOTE: For a more detailed description of asphalt shingle roofing and requirements for asphalt shingle reroofing over exist
11、ing asphalt shingles, wood shingles, roll roofing, or built-up roofing, see the “Residential Asphalt Roofing Manual,“ published by Asphalt Roofing Manufacturers Association (ARMA) and “The NRCA Steep Roofing Manual,“ published by the National Roofing Contractors Association (NRCA). Avoid reroofing w
12、ith asphalt shingles over more than one layer of existing roofing material.*NOTE: On the drawings, show:SECTION 07 31 13 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. Pitch of substrate/shingle roofing2. Detail of crickets and flashings at
13、 chimneys3. Detail at eave/rake corner of roof including underlayment, drip edge, starter strip, shingle exposure, shingle courses, and fastener placement.*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the guide specification. The publication
14、s are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Arti
15、cle. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be deleted from this section of the project specification when you choose to reconcile references in the publish print process.*The publications listed below form
16、a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.ASTM INTERNATIONAL (ASTM)ASTM D 226/D 226M (2009) Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and WaterproofingASTM D 3018/D 3018M (2011
17、) Standard Specification for Class A Asphalt Shingles Surfaced With Mineral GranulesASTM D 3462/D 3462M (2010a) Standard Specification for Asphalt Shingles Made From Glass Felt and Surfaced with Mineral GranulesASTM D 4586 (2007) Asphalt Roof Cement, Asbestos-FreeASTM D 6380 (2003; R 2009) Standard
18、Specification for Asphalt Roll Roofing (Organic Felt)ASTM D1970/D1970M (2011) Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep SECTION 07 31 13 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Roofing Underlayment for Ice
19、Dam ProtectionASTM D3161 (2009) Standard Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)ASTM D41/D41M (2011) Asphalt Primer Used in Roofing, Dampproofing, and WaterproofingASTM D4869/D4869M (2005e1; R 2011) Standard Specification for Asphalt-Saturated Organic Felt Underlayme
20、nt Used in Steep Slope RoofingNATIONAL ROOFING CONTRACTORS ASSOCIATION (NRCA)NRCA 0418 (2009) Steep-slope Roof System ManualU.S. GREEN BUILDING COUNCIL (USGBC)LEED (2002; R 2005) Leadership in Energy and Environmental Design(tm) Green Building Rating System for New Construction (LEED-NC)UNDERWRITERS
21、 LABORATORIES (UL)UL 2218 (2010) UL Standard for Safety Impact Resistance of Prepared Roof Covering MaterialsRef TitleUL 790 (2004; Reprint Oct 2008) Standard Test Methods for Fire Tests of Roof Coverings1.2 DEFINITIONS1.2.1 Top LapThat portion of shingle overlapping shingle in course below.1.2.2 He
22、ad LapThe triple coverage portion of top lap which is the shortest distance from the butt edge of an overlapping shingle to the upper edge of a shingle in the second course below.1.2.3 ExposureThat portion of a shingle exposed to the weather after installation.1.3 SUBMITTALS*NOTE: Review submittal d
23、escription (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the minimum required for adequate quality control.A “G” following a submittal item indicates that the SECTION 07 31 1
24、3 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-submittal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractor
25、s Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal tags may be used following the “G“ designation to indicate the
26、 approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes
27、following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government approval is required for submittals with a “G“ designation; submittals not having a
28、 “G“ designation are for Contractor Quality Control approval.for information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Government. The following shall be submitted in accordance with Section 01 33 00 SUBMITTAL PROCEDURES
29、:SD-03 Product DataShinglesSubmit data including type, weight, class, UL labels, and special types of underlayment and eave flashing.Local/Regional Materials; (LEED)Recycled Materials; (LEED) SD-04 Samples*NOTE: Select color according to local practice, except use light-reflective colors for air con
30、ditioned buildings. Where color is specified in paragraph entitled “Asphalt Shingles,“ delete the requirement for submittal of color charts.*Shingles; G; G, _Full shingle sample and manufacturers standard size samples of materials and products requiring color or finish selection.SECTION 07 31 13 Pag
31、e 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- Color charts; G; G, _ SD-08 Manufacturers InstructionsApplication1.4 DELIVERY AND STORAGEDeliver materials in the manufacturers unopened bundles and containers bearing the manufacturers brand name.
32、Keep materials dry, completely covered, and protected from the weather. Store according to manufacturers written instructions. Roll goods shall be stored on end in an upright position or in accordance with manufacturers recommendations. Immediately before laying, roofing felt shall be stored for 24
33、hours in an area maintained at a temperature not lower than 10 degrees C 50 degrees F.1.5 WARRANTIES*NOTE: The warranty clauses in this guide specification have been approved by the Government. The paragraphs may be used without any request for waiver.*Warranties shall begin on the date of Governmen
34、t acceptance of the work.1.5.1 Manufacturers Warranty*NOTE: Specify 30-year warranty for projects remotely located and subject to severe wind loadings; for example, in Bermuda. Specify the 25-year warranty for other projects. Minimum warranty period shall extend beyond (1) one year.*Furnish the asph
35、alt shingle manufacturers standard 25 year 30 year other warranty for the asphalt shingles. The warranty shall run directly to the Government.1.5.2 Contractors WarrantyThe Contractor shall warrant for 5 years that the asphalt shingle roofing system, as installed, is free from defects in workmanship.
36、 When repairs due to defective workmanship are required during the Contractors warranty period, the Contractor shall make such repairs within 72 hours of notification. When repairs are not performed within the specified time, emergency repairs performed by others will not void the warranty.1.6 QUALI
37、TY ASSURANCE1.6.1 Local/Regional Materials*NOTE: Using local materials can help minimize transportation impacts, including fossil fuel consumption, air pollution, and labor. Using SECTION 07 31 13 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
38、-materials harvested and manufactured within a 500 mile radius from the project site contributes to the following LEED credit: MR5. Coordinate with Section 01 33 29 LEED(tm) DOCUMENTATION. Use second option if Contractor is choosing local materials in accordance with Section 01 33 29 LEED(tm) DOCUME
39、NTATION. first option shall not be used for USACE projects. Army projects shall include second option only if pursuing this LEED credit.*MR5; Submit documentation indicating distance between manufacturing facility and the project site. Indicate distance of raw material origin from the project site.
40、Indicate relative dollar value of local/regional materials to total dollar value of products included in project.See Section 01 33 29 LEED(tm) DOCUMENTATION for cumulative total local material requirements. Roof shingles and materials may be locally available.1.6.2 Recycled Materials*NOTE: Detailed
41、information concerning EPA requirements on recycled/recovered materials is available at the following URLs: http:/www.epa.gov/cpg/products/and then click on the appropriate item from the list (building.htm for building insulation, for example).http:/www.epa.gov/cpg/products.htm(similar results).http
42、:/www.gov/cpg/pdf/back.pdf which opens up EPA530-R-98-003 (dated July, 1998, titled BACKGROUND DOCUMENT FOR PROPOSED CPG III AND DRAFT RMAN III).Using data from listed locations, fill in blank space (below and in subsequent paragraphs) for required percentage of recycled or recovered material. This is in accordance with the requirements of 40 CFR 247 and Section 01 62 35 RECYCLED/RECOVERED MATERIALS, which should be included in all projects. *MR4; Submit documentation indicating percentage of post-industrial and post-consumer recycled
