1、A-A-5 5 O O 4 Sep t.ember i (:) I 1990 SUPERSEDING (See Heading) COMMERCIAL ITEM DESCRIPTION LAMP, FLUORESCENT, F96/T12/(COLOR)/IS The General Services Administration has authorized the use of this Commercial Item Description (CID) as replacement for CIDs A-A-1583, A-A-l852A, A-A-I853A, A-A-l854A, A
2、-A-l855A, and Federal Specifications W-L-O0116/43A, /44A, and /45A which are canceled, 1, Abstract, This CID describes the general requirements for procureBent of one type fluorescent lamp of certain colors used for typical illumination. 2. Salient characteristics. This Commercial Item Description (
3、CID) covers F96/T-12, instant-start, fluorescent lamps, 75 watt, 425 ma, 96 inch nominal length, single pin contact base, 12,000 hours average rated life at 3 hrs/ start, further described in table I. Table I. ColorJlumen characteristics. Initial lumens2 (after 100 hrs burning) Lumens at 4800 hours2
4、 CID based part ID number3 Beneficial comments (recommendations, additions, deletions) and any perti- umt data which may be of use in improving this document should be sent by letter to: Commander, Defense General Supply Center, ATTN: Parts Control Branch (SSC), Richmond VA 23297-5000. I OMB control
5、 number N/A FSC 6240 DISTRIBUTION STATEMENT A: Approval for public release; distribution is unlimited, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55004 b2 9977974 0057035 1 A-A-5 500 4 Footnotes to table I: Dimensional and electrical charact
6、eristics shall be in accordance with ANSI C78.3, In compliance with ANSI C78.376, where applicable. Color temperature and 2Indicates the average nominal value per lamp on a lot basis. 3These part identification numbers are for government purposes and do not color rendering index CRI are approximates
7、, constitute a requirement for the contractor. 3. Contractor certification, The contractor shall certify and maintain sub- stantiating evidence that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices. The Government reserves the right to re
8、quire proof of such conformances prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 4. Metric Products, Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided
9、they fall within the tolerances specified using conversion tables contained in the latest revision of Federal Standard No, 376, and all other requirements of this Commercial Item Description are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specifi
10、ed in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. 5. Regulatory requirements. The offeror/contractor is encouraged to use recovered materials in acco
11、rdance with Public Law 94-580 to the maximum extent practical. 6. Preservation, packaging, packing, labeling, and marking. Preservation, packag- ing, packing, labeling, and marking shall be as specified in the contract or order. If not specified in the contract or order shall comply with ASTM D-3951
12、 6.1. Anti-counterfeit marking, When an item has been deemed to be susceptible to counterfeiting, each item shall be marked in such a manner as to provide the contracting activity with an authentication and traceability track to the true manufacturer, manufacturer and provided to the quality assuran
13、ce office of the contracting agency by. secure means. The method in which this is done shall be proprietary to the true 2 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5 5 O O 4 7, Notes, - date of solicitation shall be used to determine comp
14、liance with these requirements. The issues of ANSI C78.3, C78.376, and ASTM D-3951 in effect on the (Copies of ANSI Standards are available from the American NationalStandards Institute, 1430 Broadway, New York NY 10018.) (Copies of ASTM Standards are available from the American Society for Testing
15、and Materials, 1916 Race Street, Philadelphia, PA 19103.) Purchaser should specify the following ordering data; Title, number and date of this document CID based part identification number Brand names and National Stock Numbers are listed in table II: Table II, Brand names and stock numbers CID part
16、 National Stock Commercial Manufacturer Frl Numbers (NSNs) stock number CAGE codel 111 /TI 06107 , 1HT85 , 62607 , A55004-2 6240-00-681-1639 F96T12/CWX 08599, 08805, 1HT85, %;:9, 58325, 62607 - lFootnote to table II: Commercial And Government Entity (CAGE) code definition: 06172 - Marvel Lamp Co, In
17、c, 2083 Center Ave, Ft . Lee, NJ 07024-4999, 08599 - Arc Ray Electric CO., 350 5th Ave., Empire State Bldg. NY, 08808 - General Electric Co, Lamp Glass and Components Dept, 24400 Highland lHT85 - GTE Products Corp, Lighting Center, Danvers MA 01923 56589 - 2lst Century Enterprises Inc, 725 Industria
18、l Rd., San Carlos, 62607 - North American Phillips Lighting Corp., A Div, 1 Westinghouse Plaza 85271 - Duro Test Corp., 9 Law Dr, Fairfield, NJ 0700.7 NY 10001-5100 Rd, Richmond Heights, OH 44143-2503, CA 94070-3310, Bloomfield, NJ 07003-4601. - 3 Provided by IHSNot for ResaleNo reproduction or netw
19、orking permitted without license from IHS-,-,-A-A-55004 62 M 797777i$ 0057037 5 M A-A-55004 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITIES: Military Coordinating Activity COMMERCE - NIST Navy - AS GSA - FSS Custodians Air Force - 99 Amy - ME Navy - SH PREPARING ACTIVITY: Navy - AS AGENT : DLA - GS Project 6240-1111 FSC 6240 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
