欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GMKOREA EDS-T-7134-2008 DETERMINATION OF THE FORCE-DEFLECTION CHARACTERISTICS AND PERMANENT SET OF ELASTOMERIC COMPONENTS.pdf

    • 资源ID:757235       资源大小:108KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GMKOREA EDS-T-7134-2008 DETERMINATION OF THE FORCE-DEFLECTION CHARACTERISTICS AND PERMANENT SET OF ELASTOMERIC COMPONENTS.pdf

    1、GM DAEWOO Auto # Total accuracy ; Force measuring equipment : 1.5% of the measured value. Displacement measuring equipment : 0.05 mm 4.2. Environmental chamber for use on the testing machine. The environmental chamber shall be of the air-circulating type, and comply with the following requirements ;

    2、 Temperature range : -40 +250 Temperature variation : 2K Temperature change rate : 1.5 K/minute for empty cabinet 4.3. Suitable fixtures for locating and attaching the elastomeric components to the test machine. EDS-T-7134DETERMINATION OF THE FORCE-DEFLECTION CHARACTERISTICS AND PERMANENT SET OF ELA

    3、STOMERIC COMPONENTS PAGE: 3/5 ISSUED DATE: 1988. 07. 15 REVISED DATE: 2008. 10. 15 VERSION: 5 GM DAEWOO Auto & Technology 4.4. Dimensional measuring equipment 4.4.1. Dimensional measuring equipment, e.g. a linear dial gauge to DIN 878 or BS 907, with a range of 10mm an accuracy of 0.01mm, and extend

    4、ing a relatively constant force of less than 2N over its range of travel. 4.4.2. Gauge block to DIN 862 or BS 4311. 4.4.3. Precision height vernier accurate to 0.1mm, height max. 500mm. 5. PRECAUTIONANDTESTMETHOD 5.1. Precaution 5.1.1. Requirement for force-deflection test The test shall be carried

    5、out at a room temperature and comply with the force and the test direction specified on the drawing. Care shall be taken that the test piece is not deflected during mounting into the fixture. If the test result is inappropriate, the test piece shall be tested again after at least 24 hours. If the fo

    6、rce, on the force indicating device on the test machine is influenced by the weight of the test piece and/or its fixtures, compensation shall be made prior to the commencement of the test. 5.1.2. Precaution for permanent set test The temperature of chamber and the test period shall be observed, taki

    7、ng care that the test piece is not deflected during mounting into the fixture. 5.2. Test method 5.2.1. Test method for the force-deflection characteristics. (1) The unstressed height ho shall be measured prior to testing. (2) After attaching the test piece to the fixture, the initial force Fvshall b

    8、e applied to the test piece and removed at the same velocity. This procedure shall be repeated until the zero range is within 0.01mm (generally repeated 3 times). Test speed for force-deflection characteristics is referred to test condition of force-deflection mapping (see relevant component DWG) (3

    9、) Apply Fvto the test sample, and then adjust as zero point. Fkshall be applied to the test piece after the given period(6 , 60 , 600 , 6000 seconds), the deflection shall be measured. For S6measurement, the deflection shall be measured after 6seconds. For S6000, after 6000 seconds. (4) For the cree

    10、p characteristics test, the deflection shall be generally measured after 6000 seconds, but may be calculated from the following formula so as to reduce the test period. S6000= 1.5(S600- S6) Both S6and S600shall be measured, and the difference between two shall be multiplied by 1.5 to obtain the valu

    11、e. (5) If specially specified as EDS-T-7134 on drawing, the test shall be carried out as follows. The force of 1.25(Fv+ Fk) shall be applied to and removed from the test sample 5 times prior to testing. After removal, the test EDS-T-7134DETERMINATION OF THE FORCE-DEFLECTION CHARACTERISTICS AND PERMA

    12、NENT SET OF ELASTOMERIC COMPONENTS PAGE: 4/5 ISSUED DATE: 1988. 07. 15 REVISED DATE: 2008. 10. 15 VERSION: 5 GM DAEWOO Auto & Technology sample shall be maintained for 16 to 48 hours. S6 and S6000shall be determined according to steps (1) (4). (6) Calculation Creep S6000= 1.5(S600- S6) Force-deflect

    13、ion characteristics S6000= S6+ S6000Installed height H = ho- S60005.2.2. Test method for permanent set (1) S6and S6000shall be calculated through the force-deflection characteristics test to clause 5.2.1. The test sample shall be maintained for 241 hours at room temperature and tested as follows. (2

    14、) The test sample shall be inserted to the test fixture, and the distance between the upper fixture and the bottom fixture shall be measured. Thereafter, the distance between fixtures shall be adjusted in compliance with the deflection of S6+ S6000using the bolt attached to the fixture. (3) The test

    15、 sample shall be placed into chamber, and maintained for given period at the temperature specified on the relevant component drawing. (4) At the end of specified period, the test sample shall be removed from the chamber and maintained for 61 hours at 235k with still stressed. (5) The stress shall be

    16、 removed, and the test sample shall be detached from the test fixture. After 603 minutes, hsshall be measured in the same way as hois measured. (6) The test result shall be calculated as follows, and evaluated according to the specification of the appropriate component drawing. (%) ) - () - (= SET P

    17、ERMANENT )III 9JPJTJPJ (7) Code of Test Condition Code of Test Condition shall be specified by Code on the following table indicated on the relevant component drawing. Condition Code Letter 0 Duration (H) -2 Temperature ( K ) A 24 -30 3 B 24 -20 3 C 24 -10 3 D 24 +80 2.5 E 24 +100 2.5 F 24 +125 2.5

    18、G 24 +150 2.5 H 24 +175 2.5 I 24 +200 2.5 K 24 +225 2.5 L 72 +23 5 M 72 +80 2.5 EDS-T-7134DETERMINATION OF THE FORCE-DEFLECTION CHARACTERISTICS AND PERMANENT SET OF ELASTOMERIC COMPONENTS PAGE: 5/5 ISSUED DATE: 1988. 07. 15 REVISED DATE: 2008. 10. 15 VERSION: 5 GM DAEWOO Auto & Technology Condition

    19、Code Letter 0 Duration (H) -2 Temperature ( K ) N 72 +100 2.5 O 72 +125 2.5 P 72 +150 2.5 Q 72 +175 2.5 R 72 +200 2.5 S 72 +225 2.5 T 168 +80 2.5 U 168 +100 2.5 V 168 +125 2.5 W 168 +150 2.5 X 168 +175 2.5 Y 168 +200 2.5 Z 168 +225 2.5 6. CODING SYSTEM The requirements for the Permanent Set of elast

    20、omeric components shall be specified on drawings, test specifications and material specifications etc. as follows. e. g PERMANENT SET to EDS-T-7134 - XB1 - MAX 20% Specification Test condition Test method Designation 7. DEVIATIONS Deviations from the requirements of this test method (e.g. test piece

    21、 preparation, test fixture, time and temperature of test) shall have been agreed upon. These shall be specified on engineering drawings, material specifications etc. and shall be indicated on test certificates, report etc. 8. REFERENCE GME 60 231 Determination of the force-deflection characteristics and creep properties of elastomeric components


    注意事项

    本文(GMKOREA EDS-T-7134-2008 DETERMINATION OF THE FORCE-DEFLECTION CHARACTERISTICS AND PERMANENT SET OF ELASTOMERIC COMPONENTS.pdf)为本站会员(registerpick115)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开