欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GME GMI L-6X01-5-1998 Camshaft Wear Test (English German Includes Appendix 1-18 ITDC Release Draft for Harmonization).pdf

    • 资源ID:755469       资源大小:2.40MB        全文页数:31页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GME GMI L-6X01-5-1998 Camshaft Wear Test (English German Includes Appendix 1-18 ITDC Release Draft for Harmonization).pdf

    1、Camshaft Wear Test File name: 65068-.doc DM GMB HOLDEN ISUZU SAAB ITDC Prepared: Kr Krmme1 i Nockenwellen - Verschleitest Approved GM do Brasil Approved Saab Approved ISUZU Approved Delta Motor Approved Holden Approved Dr. H. K. Kemmann Dr. G. Reinheimer R. Schneider ITDC July 1998 Page 1 of 31 6 a

    2、E- LBSP GMI TP l 03/96 GM INTERNATIONAL ENGINEERING STANDARD Draft GMI L-6x014 Revisions nderungen Date Paragraph Datum Abschnitt 07.98 ITDC Release 07.98 ITEZ - Freigabe Replacement for GME L-XOl-5 Ersatz fr GME L-XOl-5 Page 2 of 31 July 1998 LBSP GMI 2 11195 GM INTERNATIONAL ENGINEERING STANDARD D

    3、raft GMI L-6x01-5 I Introduction 1.1 Purpose Testing wear characteristics for tribological system elements, camshafts (cams), cam follower, tappet, tappet bridge, and roller-type cam follower while paying special attention to the finish quality and the materials or material combinations. 1.2 Forewor

    4、d In conjunction with the test oil, the camshaft wear test shall investigate the wear behaviour of the tribo- logical system elements, cams and cam followers in operating engines with heavily polluted gasoline engine oil under defined operating conditions after a specified operation period and compa

    5、red with alter- native system element characteristics (materials, component geometry, surface roughness, etc.). 1.3 Applicability Camshafts (cams), cam followers, taDpets, tappet bridges and roller-type cam followers for all gasoline an8 diesel engines 1.4 Definitions N.a. 1.5 References 1 S.1 Order

    6、 of Precedence In the event of a conflict between the text of the test procedure and the documents cited herein, the text of the test procedure takes precedence. Nothing in the test procedure, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Remark:

    7、In the event of a conflict between the Eng- lish and the domestic language, the English lan- guage shall take precedence. 1.5.2 Government Documents N.a. I Einleitung 1.1 Zweck Erprobung des Verschleiverhaitens von tribotech- nischen Cystemelementen Nockenwellen (Nocken), Schlepphebel, Stel, Stelbrc

    8、ken und Rollen- schlepphebel bei besonderer Beachtung der Bear- beitungsqualitt und der Werkstoffe bzw. Werkstoff- Paarungen. 1.2 Vorwort Mit dem Nockenwellen-Verschleitest in Verbindung mit dem Testl soll in befeuerten Motoren nach festgelegten Laufzeiten das Verschleiverhalten der tribotechnischen

    9、 Systemelemente Nocken und Nok- kenfolger unter definierten Betriebsbedingungen mit stark verschmutztem Otto-Motorenl untersucht und mit Varianten der Systemelemente-Eigenschaften (Werkstoffe, Bauteilgeometrie, Oberflchenrauheit, pir ,.) verglichen werden. i ,3 Anwendbarkeit Nockenwellen (Nocken), S

    10、chlepphebel, Stel, S;rlbrcken unc Rollenschlepphebel von allen Seo- una Dieselmotoren. i .4 Definitionen N.a. 1.5 Referenzen 1 S. Rangfolge der Dokumente lm Falle eines Widerspruchs vom Text dieses Priif- verfanrens und den Dokumenten, die in dem Prf- verfanren enthalten sind. hat der Text des Prfve

    11、r- fahrens Vorrang. Falls keine Ausnahmen vereinbart wurden, darf cas Prfverfahren keine anzuwenden- cen Gesetze und Regelungen auer Kraft setzen. Hinweis: Im Falle von Unstimmigkeiten zwischen aem englischen und dem landessprachlichen Text, ist der englische Text ausschlaggebend. 1.5.2 Staatliche D

    12、okumente N.a. July 1998 Page 3 of 31 I LBSP GMI 2 11 /95 -STD-OPEL GUI L-bXUL-5-GERM 1998 8597338 0U2421b 1T8 6 GM INTERNATIONAL ENGINEERING STANDARD Draft GMI L-6x014 1 S.3 General Motors Documents 1.5.3.1 GMIO B 0401013 First Fill Oil for Otto Engines B 0401055 Maximum Pressure Lubricating Oil LBC

    13、H02-03 Test Procedure for Insolubles in Used Lubricating Oils 1.5.3.2 NAO N.a. I .5.4 Industry Documents N.a. 1.5.5 Supplier Documents N.a. I S.6 Other Documents N.a. 2 Resources 2.1 Facilities N.a. 2.2 Equipment 2.2.1 All types of gasoline and diesel engines. 2.2.2 Surface measurement equipment (e.

    14、g., Perthen Perthometer including feed equipment). 2.2.3 Form measurement machine (e.g., FAG - FMS 21 00). 2.2.4 Roundness measuring instrument (e.g., Perthen MMK 2). 2.2.5 Recording instrument (e.g., Perthen Macrograph). 1.5.3 General Motorc Dokumente 1.5.3.1 GMIO B 0401013 ErstbefIII fr Ottomotore

    15、n B 0401055 Hchstdruckschmierl LBCH02-03 Bestimmung der festen Fremdstoffe in gebrauchten Motorien 1.5.3.2 NAO N.a. 1 S.4 Industrie Dokumente N.a. 1.5.5 Lieferanten Dokumente N.a. 1 S.6 Andere Dokumente N.a. 2 Gerte und Einrichtungen 2.1 Einrichtung N.a. 2.2 Ausrstung 2.2.1 Alle Otto- und Diesel-Mot

    16、or-Typen. 2.2.2 Oberfichenmegert (z.B. Perthen Perthometer) inkl. Vorschubeinrtchtung. 2.2.3 Formmemaschine (2.B. FAG - FMS 2100). 2.2.4 Rundheitsmeeinrichtung (Z.B. Perthen MMK 2). 2.2.5 Auzeichnungsgert (z.B. Perthen Macrograph). i. Page 4 of 31 July 1998 LBSP GMI 2 11/95 STD-OPEL GMI L-bXDL-5-GER

    17、M 1998 8577338 0024237 O34 E GM INTERNATIONAL ENGINEERING STANDARD Draft GMI L-6x01-5 2.2.6 Mixture of 50 % used diesel oil + 50 % unused oil (B 0401013, with SAE lOW30). The sedimentary content of the test oil shall be determined to LBCH02-03 and shall be (0.8 to 1.2) % by mass. The sedimentary con

    18、tent of every test oil fill shall be checked using laboratory oil testing. The test oil and oil filter shall be replaced following an operating period of 200 h. 2.3 Test VehiclelTest Piece Camshafts (cams), cam followers, tappets, tappet bridges and roller-type cam followers. 3 Procedure 3.1 Prepara

    19、tion The cam, cam follower, tappet, tappet bridge and roller contact surfaces shall be lighted coated with hypoid oil as specified in B O401055 prior to instaila- tion. The contact surfaces of the parts shall be coated with :he test oil during installation after intermediate measurements. 3.2 Condit

    20、ions Deviations from the requirements of this :es: proce- dure shall have been agreed upon. Such require- ments shall be specified on component drawings, test certificates, reports etc. 3.3 Instructions 3.3.1 Measurement of Camshaft, Cam Follower, Tappet, Tappet Bridge and Roller-type Cam Follower T

    21、he cam height, cam transverse profiles and the contact surface contours of the cam follower as well of the diameter of the tappets shall be measured before testing is commenced. In addition, the component roughness measure- ments shall be measured as specified in the drawings and checked for complia

    22、nce with the drawing tolerances (measurement system e.g., S6P Perthen). 2.2.6 Mischung aus 50 % Diesel Altl + 50 % Frischl (6 0401013, mit SAE 10W30). Der Sedirnentgehalt des Testls ist nach LBCH02-03 ZU ermitteln und mu (0,8 bis 1,2) Gew. % betragen. Der Sediment- gehalt jeder Testl-Charge St anhan

    23、d von Labor- Olproben ZU kontrollieren. Nach einer Laufzeit von 200 h sind Testl und Olfilter ZU wechseln. 2.3 VersuchsfahrzeuglProbekrper Nockenwellen (Nocken), Schlepphebel, Stel, Stelbrijcken und Rollenschlepphebel. 3 Durchfhrung 3.1 Vorbereitung Vor dem Einbau sind die Nocken und die Schlepp- he

    24、bel-, Stel-, Stelbrcken- und Rollen- Laufflchen leicht mit Hypoid-Ol nach 8 0401055 einzstreichen. Beim EinSac nach Zwischenmessungen sind die Lauflchen der Teiie mit dem Testol einzustreichen. 3.2 Prfbedingungen AbWeichunsen von den Bedingungen dieses Prf- Verfahrens mssen vereinbart werden. Diese

    25、Be- dinungen sind auf Teilzeichnuflgen vorgeschrieben bzw. mssen auf Prfieugnissen, Berichten u. dergl. angegeben werden. 3.3, P ru f a ni e tu n g 3.3.1 Vermessung von Nockenwelle, Schlepphe- bel, Stel, StDelbrcken und Rolienschlepp- hebe1 Vor Testbeginn mssen die Nockenhhen, Nocken- querprofile un

    26、d die Laufflchenkonturen der Nok- kenfolger sowie die Durchmesser der Stel ver- messen werden. Auerdem sind die Bauteilrauhigkeiten nach Zeich- nungsangabe zu messen und auf Einhaltung der Zeichnungstoleranzen zu prfen (Mesystem z.B. S6P Peflhen). July 1998 Page 5 of 31 LBSP GMf 2 11/95 ETDOOPEL Ti0

    27、 GM INTERNATIONAL ENGINEERING STANDARD Draft GMI L-6x014 3.3.1.1 Measurement of the cam heights and trans- verse profiles The maximum cam height shall be measured in the center of the cam for each measurement. An appa- ratus shall be used for measurement (see fig. I). The cam transverse profiles, th

    28、e cam peaks and the cam base circles shall be recorded parallel to the camshaft axis using a form measurement machine (e.g., FAG-FMS 2100) (see appendix 1). 3.3.1 .I Vermessung der Nockenhhen und Nok- kenquerprofile Bei der Vermessung wird jeweils die maximale Nok- kenhhe in der Mitte des Nockens ve

    29、rmessen. Zur Vermessung ist eine Vorrichtung (siehe Abb. 1) zu verwenden. Die Nockenquerprofiie der Nockenspit- zen und Nockengrundkreise sind achsparallel zur Nockenwellenachse mit Hilfe einer Formmema- schine (z.B. FAG-FMS 2100) auzunehmen (siehe Anhang i). I c-2 Fig. 1 : Measurement layout for ba

    30、sic rneasurernents 1 Dial gauge 2 Concave 3 Center 4 I cam 5 8* cam As a result the axial inclined position and if neces- sary the hollow grinding profile of the camshaft contact surfaces are measurable. This method shall also be used to measure the maximum linear wear abrasion of the associated cam

    31、 if there is asymmet- rical cam wear. This value indicates the characteris- tic amount of cam wear taking into account of the cam height. The preferred positions and measurement ranges for the cam roughness measurements (cam peak I cam base circle), which are primarily used for the purposes of compa

    32、rison are presented in appendix 2. ASb. : : Meanordnung Basismessunc 1 Meuhr 2 baliig 3 Mitte 4 1. Nocken 5 8. Nocken Dadurch werden die benenfalls auch das laumachen mebar. axiale Schrglage und gege- Hohlschliffprofil der Nocken- Der maximale lineare Ver- schleiabtrag des jeweiligen Nockens soll au

    33、f diese Weise auch bei asymmetrischem Nockenverschlei gemessen werden. Dieser Wert gibt unter Berck- sichtigung der Nockenhhe den kennzeichnenden Nockenverschleibetrag an. Die bevorzugten Positionen und Mebereiche der Nocken-Rauhigkeitsmessungen (Nockenspitze I Nockengrundkreis), die primr zu Vergle

    34、ichczwek- ken verwendet werden, sind in Anhang 2 dargestellt. Page 6 of 31 July 1998 LBSP GMI 2 11/95 r GM INTERNATIONAL ENGINEERING STANDARD Draft GMI L-6x01-5 i 3.3.1.2 Measurement of the contact surfaces of the cam follower and tappet bridge. The longitudinal profiles for the contact surfaces of

    35、the cam followers and tappet bridges shall be traced and recorded in the running direction using a round- ness measurement instrument (e.g. Perthen MMK2) in conjunction with a recording instrument (e.g. Perthen Macrograph). It has proved advantageous in determining the precise radius of the contact

    36、surface curvature using the roundness measure- ment instrument. The contact surface is thereby displayed as a straight line and permits unevenness to be easily detected (even during the initial measurement) (e.g. caused in production). When measuring the worn parts, the radius deter- mined for each

    37、cam follower or tappet bridge con- tact surface shall be set for the initial measurement on the roundness measurement instrument. The contact surface shall then be traced and recorded. The display permits the maximum wear and the distribution of the linear wear abrasion to be dis- played clearly. Us

    38、e ci the longitudinal profile for determining the maximum wear abrasion shall be preferred. 3.3.1.3 Measuring the tappet contact surfaces The contact suriaces of the tappe! shall be traced and recorded as accurarely as possible alon the tppe? center line using a su taopet bridge-: roller wear vclues

    39、 I the permissible bogey. 3.4.2 Evaluation The determined surface roughness values, meas- ured values of the component geometry and the abraded wear shall be presented in a table and in a graph. In addition, the material fatigue of the components shall be assessed using the pitting according to the

    40、photographic evidence. The wear behaviour of the corresponding camkarn follower matching (based on the comparison of the initial, intermediate and final measurements) shall be presented graphically. 3.4.3 Presentation With reference to this test procedure the results of the measurements shall be pre

    41、sented in a test re- poft. 3.3.4.2 Untersuchung der Teile im Werkstoffiabor Hierbei erfolgen die Dokumentation des Verschlei- erscheinungsbildes der Bauteile und eingehende metallographische und metallurgische Untersu- chungen der Bauteiloberflachen und obetflachenna- hen Werkstoffschichten. Mit Hil

    42、fe gegebenenfalls erforderlicher Sonderanaly- severfahren (REM, Mikroanalysen, Eigenspan- nungsmessungen, etc.) wird angestrebt, verschlei- relevante Parameter der Oberfichen- und Werk- stofktruktur der beteiligten Bauteilpartner (Nocken und Nockenfolger) zu ermitteln und primre Ver- schleimechanism

    43、en (Polierverschlei, Frever- schlei, Ermdungsverschlei, etc.) sowie Ursa- chen fr extreme Verschleiniveaus aufzuzeigen. Der Vergleich der Verschleimedaten und der Untersuchungsergebnkse des Werkstofflabors er- laubt eine tribotechnische Gesamtbewertung der Bauteilpaarung NockenlNockenfolger im Rahme

    44、n der Motorverschleiversuche. Ziel ist die Erarbeitung von Freigabeinformationen fr die Motorproduktion bzw. die Klrung von prim- ren U rsachen bei auftretenden Verschlei p roble- men. 3.4 Ergebnisse 3.4.1 Forderungen Der Versucn wird positiv bewertet. wenn jeweils drei 200 h - Laufe mit neuen Teile

    45、n mit Nocken- und CioellSchieppheDel- /Stoelbrucken- Rollen-Ver- schieiwerten I den zuiassigen Bocey abgeschlos- sen werden 3.4.2 Auswertung Die eriaten Oberflchenrauhheitskennwerte, Mewerte der Bauteilgeomotrie und des Ver- schleiabtrages sind tabellarisch und in bersichtc- graphiken darzustellen.

    46、Zustzlich ist die Materialerrndung der Bauteile anhand der Pittingbildung nach der Fotorichtreihe zu beurteilen. Das Verschleiverhalten der jeweiligen Nocken/Nockenfolger-Paarung ist aus dem Ver- gleich Anfangs- zu Zwischen4Endvermessung gra- phisch darzustellen. 3.4.3 Darstellung Unter Angabe diese

    47、s Prfveffahrens sind die Er- gebnisse der Messung in einem Prfericht zu- sammenzustellen. JUIY wa Page 9 of 31 CBCP GMI 2 11/95 STDaOPEL GMI L-bXDZ-5-GERfl 1998 8597LL9 0024222 YTL - GM INTERNATIONAL ENGINEERING STANDARD Draft GMI L-6x01-5 4 Coding System 4 Angabe in Dokumenten This test procedure s

    48、hall be called up in other specifications, drawings, VTS, CTS etc. as follows: Dieses Prfverfahren ist in anderen Dokumenten, Zeichnungen, VTS, CTS etc. wie folgt anzugeben: Example: “Test to GMI L-GXOI-5“ Beispiel: “Prfung nach GMI L-6X01-5“ July 1998 Page 10 of 31 LBSP GMI 2 11/95 STD-OPEL GMI L-b

    49、XOL-5-GERM 1718 8597118 0024223 338 - GM INTERNATIONAL ENGINEERING STANDARD Draft GMI L-6x01-5 1 Appendix I Cam Transverse Profile Measurements Anhang I Nocken-Querprofile-Vermessungen 1 Cam tip transverse profile (over 17 mm) 1 Quer?rofil Nockenspitze (Meweg 17 mm) 2 Cam height 2 Nockenhohe 3 Cam base circle transverse profile (over 17 mm) 4 Measurement feed 4 Mevorschub 3 Querprofil Nocken-Grundkreis (Meweg 17 mm) Plotleci scale ajo pm Me3schriebm


    注意事项

    本文(GME GMI L-6X01-5-1998 Camshaft Wear Test (English German Includes Appendix 1-18 ITDC Release Draft for Harmonization).pdf)为本站会员(confusegate185)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开