欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD FLTM BO 117-02-2001 IMPACT TEST FOR PLASTICS (Replaces FLTM BO 017-02)《塑料的冲击测试 代替FLTM BO 017-02(代替 FORD FLTM BO 017-02)》.pdf

    • 资源ID:747358       资源大小:198.49KB        全文页数:11页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD FLTM BO 117-02-2001 IMPACT TEST FOR PLASTICS (Replaces FLTM BO 017-02)《塑料的冲击测试 代替FLTM BO 017-02(代替 FORD FLTM BO 017-02)》.pdf

    1、 FORD LABORATORY TEST METHOD BO 117-02 Date Action Revisions 2001 03 28 Revised Editorial no technical change A. Cockman 1996 10 16 Printed copies are uncontrolled Page 1 of 11 Copyright 2001, Ford Global Technologies, Inc. IMPACT TEST FOR PLASTICS Application This method is used to determine the im

    2、pact resistance of plastics. Apparatus Required Impact Test Stand The test fixture used for this test consists of a heavy metal base to which is mounted a sample support ring of 2 inches (50.8 mm) inside diameter. The inside perimeter of the sample support is cut to 1/4 inch (6.35 mm) radius. Mounte

    3、d and centered over the support ring is a carrier which holds the impact dart. The dart is free to move in its carrier and rests on the sample under static conditions. The dart has 1/2 inch (12.7 mm) diameter with one end rounded to 1/4 inch (6.35 mm) radius; the other end has a 1 inch (25.4 mm) dia

    4、meter flat impact head. The dart is long enough to protrude 3/4 inch (19.1 mm) below the sample plane into the support ring. Impact weights are 1 inch (25.4 mm) diameter metal rods and are dropped through a guide tube which is mounted and centered over the impact dart. The tube has 1 1/32 inch (26.2

    5、 mm) diameter and is 50 inches (1270 mm) long. Its entire length is slotted and calibrated into 1 inch (25.4 mm) increments along the slot. The weights are lifted by a pin which protrudes through the slot in the guide tube. A wide selection of weights from pound (113 g) to 10 pounds (4.54 kg) should

    6、 be available so that any force range can be maintained with a weight velocity at impact of 7 to 15 ft/s (2.1 to 4.6 m/s). Guide tube calibrations are clearly marked so that when the weight is raised to a specific height and dropped, it strikes the impact dart driving it against the sample with a sp

    7、ecific impact force in inch pounds. Freezer In determining cold impact strength, a chest freezer or other cooling apparatus capable of maintaining the desired temperature within +/- 2 C should be used, such as Revco Cold Box - Model ULD 1234. Source: Revco Corporation Industrial Products Division De

    8、erfield, Michigan 48238 or equivalent. Samples Impact test samples should be injection molded 4 x 4 inch (102 x 102 mm) plaques with smooth surfaces and be all of the same thickness, either 0.100 inch (2.54 mm) or 0.125 inch (3.18 mm). FORD LABORATORY TEST METHOD BO 117-02 Page 2 of 11 Copyright 200

    9、1, Ford Global Technologies, Inc. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwis

    10、e specified. Test Procedure 1. Place a test sample on the support ring letting the dart rest freely on the surface of the sample. 2. Choose a weight which will deliver an impact force when dropped from 25 inches that is in the range of the expected impact resistance of the material to be tested. 3.

    11、After the appropriate weight is selected, the test force increment should be set at 5 % or less of the approximate impact resistance of the material. (For very low ranges, the force increment may be as high as 10 %.) 4. Impact a few plaques to verify that the weight chosen yields both passes and fai

    12、lures in the desired height range. (If more than six or seven consecutive passes are encountered, increase the force impact and start test over. Conversely, if more than six or seven consecutive failures are encountered, decrease the force and start test over). 5. After this is verified, perform the

    13、 test by the following method: (a) If the sample presently being impacted fails, the next sample will be impacted at a level one increment lower. (b) If the sample presently being impacted passes, the next sample will be impacted at a level one increment higher. Failure is defined as any evidence of

    14、 cracking. A minimum of 20 samples should be tested. The weight should not be allowed to bounce and strike the sample a second time. The sample should be held firmly and flat on the support ring during the entire procedure. If impact resistance is being determined at a sub-ambient temperature, the s

    15、ample should be held at the sub zero temperature for a minimum of 8 h and impacted within 5 s after removal from the freezer. 6. Record the data on a data sheet (example data sheet included) with force increments marked under column “F“ and failures and/or passes in the appropriate sample number box

    16、 in the center of the page. Calculations: A computer program titled “STAIR“ is available for analysis of impact data. It is stored in corporate time sharing library, and can be accessed by any user from any time sharing console using the procedure described in Exhibit III of General Parts Division R

    17、eliability Memo No. IV-12. The following procedure is given for manual analysis: FORD LABORATORY TEST METHOD BO 117-02 Page 3 of 11 Copyright 2001, Ford Global Technologies, Inc. 1. Count the number of passes and failures. Determine which occurred the least number of times. If the force range of the

    18、 least frequent event is more than 20 % of the highest force value, the confidence of the test is decreased. (For very low ranges, a 30 % variation is allowable.) 2. Starting with “O“ for the lowest force increment at which the least frequent event (pass or fail) occurs, number the force increments

    19、with ascending integers so that the highest integer corresponds to the highest force increment at which the least frequent event occurred. These numbers should be entered in Column “I“ of the work sheet. 3. Count the number of the least frequent events which occurred at each force level (horizontall

    20、y). Enter these numbers in Column “N“. For each horizontal line, multiply I x N and I2 x N and enter results in the appropriate columns. 4. Add Columns N, (I x N) and (I2 x N) so that: A = N B = (I x N) C = (I2 x N) 5. Compute the force impact sample mean by the following equation: (Space is provide

    21、d on the work sheet for calculations in Steps 5, 6, 7, and 8) x = Fo + d (B/A +/- 0.5) Where: x = Force Impact Sample Mean Fo = Lowest Force Value of Least Frequent Event d = Force Increment B/A = Mean of Force Impact Integer Value In the expression (B/A +/- 0.5) use + (plus) if the least frequent e

    22、vent is pass; use - (minus) if the least frequent event is fail. 6. Compute Upper Limit by the following equation: U = (AC B2) A2 Where: U = Upper Limit A = N B = (I x N) C = (I2 x N) If “U“ is less than or equal to 0.3, the standard deviation cannot be estimated and the test should be repeated usin

    23、g a smaller force increment. If “U“ is larger than 0.3, then continue to Step 7. FORD LABORATORY TEST METHOD BO 117-02 Page 4 of 11 Copyright 2001, Ford Global Technologies, Inc. 7. Compute the standard deviation by the following equation: S = 1.62 d x (AC B 2) 0.03) A2 Where: S = Standard Deviation

    24、 1.62 = Constant (AC-B2)/A2 = Upper Limit 0.03 = Constant 8. The impact value, R, of the material is computed as follows: R = x - .84S Where: R = Impact Resistance of Material x = Sample Mean S = Standard Deviation The impact resistance of the material is defined to be the level at which 20 % of the

    25、 samples would be expected to fail and 80 % pass. The 20 % failure level is chosen so that the material which has a high scatter of data will be penalized more than a very consistent material. 9. Report should contain: (a) Material description and identification (b) Sample number tested (c) Sample s

    26、ize and thickness (d) Mean impact level (x) (e) Standard deviation (S) (f) Expected 20 % failure level (R) to the nearest inch pound. (g) Test conditions: temperature, painted or unpainted, side of plaque impacted, etc. Statistical methods are available for more detailed analysis. If more analysis i

    27、s required, refer to General Parts Division Reliability Memo No. IV-12. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BO 117-02

    28、 Page 5 of 11 Copyright 2001, Ford Global Technologies, Inc. IMPACT TEST FOR PLASTICS Sketch 1 FORD LABORATORY TEST METHOD BO 117-02 Page 6 of 11 Copyright 2001, Ford Global Technologies, Inc. IMPACT TEST FOR PLASTICS Sketch 2 FORD LABORATORY TEST METHOD BO 117-02 Page 7 of 11 Copyright 2001, Ford G

    29、lobal Technologies, Inc. IMPACT TEST FOR PLASTICS Sketch 3 FORD LABORATORY TEST METHOD BO 117-02 Page 8 of 11 Copyright 2001, Ford Global Technologies, Inc. IMPACT TEST FOR PLASTICS Sketch 4 FORD LABORATORY TEST METHOD BO 117-02 Page 9 of 11 Copyright 2001, Ford Global Technologies, Inc. IMPACT TEST FOR PLASTICS Sketch 5 FORD LABORATORY TEST METHOD BO 117-02 Page 10 of 11 Copyright 2001, Ford Global Technologies, Inc. FORD LABORATORY TEST METHOD BO 117-02 Page 11 of 11 Copyright 2001, Ford Global Technologies, Inc.


    注意事项

    本文(FORD FLTM BO 117-02-2001 IMPACT TEST FOR PLASTICS (Replaces FLTM BO 017-02)《塑料的冲击测试 代替FLTM BO 017-02(代替 FORD FLTM BO 017-02)》.pdf)为本站会员(confusegate185)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开