欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD ESW-M2D247-A-2009 NITRILE BUTADIENE RUBBER HIGH HEAT RESISTANT - OIL SEALS TO BE USED WITH FORD WSS-M99P1111-A 《油封圈用耐高温丁腈橡胶 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    • 资源ID:746662       资源大小:30.63KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD ESW-M2D247-A-2009 NITRILE BUTADIENE RUBBER HIGH HEAT RESISTANT - OIL SEALS TO BE USED WITH FORD WSS-M99P1111-A 《油封圈用耐高温丁腈橡胶 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 08 20 N-STATUS No Replacement Named C. Mracna, NA 2004 07 23 Revised Para 3.0 inserted; para 3.4 & 4 deleted 1974 10 09 Released CW10-711072 Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 1 of 4 NITRILE

    2、 BUTADIENE RUBBER, HIGH HEAT RESISTANT ESW-M2D247-A - OIL SEALS NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by this specification are nitrile butadiene rubbers compounded specially for heat resistance significantly higher than that of conventional NBR compounds, without sacrificing

    3、other desirable properties. 2. APPLICATION This specification was released originally for material used in miscellaneous oil seal and gasketing applications for continuous automotive service at temperatures up to 135 C with occasional temperatures as high as 150 C. Type I was released originally for

    4、 static pressure seals and Type II was released originally for rotational shaft seals. The Type III material was compounded with an internal lubricant for ease of assembly. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Co

    5、mpanys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 RAW MATERIAL 3.1.1 Oscillating Disk Rheometer or Shearing Disk Viscometer (ASTM D 2084 or ASTM D 1646 respectively) The compound must have a curve or viscosity and scorch data that corresponds to original material approved f

    6、or use that is on file in the suppliers quality control office and the affected product engineering materials office. Utilizing the established operating parameters, the following ranges must be maintained: Rheometer: Type I Type II Type III ML- Minimum Torque, N-m +/- 0.4 +/- 0.4 +/- 0.4 MHF- Maxim

    7、um Torque, N-m +/- 0.9 +/- 0.9 +/- 0.9 tS2- Scorch Time for 0.2 +/- 1.0 +/- 3.0 +/- 1.0, -0.5 N-m Rise Above Minimum Torque, minutes ENGINEERING MATERIAL SPECIFICATIONESW-M2D247-A Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 2 of 4 Type I Type II Type III Viscom

    8、eter Minimum Viscosity (Mooney) +/- 8 t2.5- Scorch Time at a 2.5 +/- 0.75 min. point rise 3.2 PART 3.2.1 Specific Gravity +/- 0.03 1.30 - 1.36 1.18 +/- 0.03 (ASTM D 792) Each supplier must establish values for their compound prior to source approval and be able to maintain these values within the gi

    9、ven tolerance. 3.2.2 Hardness - Micro, IRHD 65 - 75 75 - 85 68 - 78 (ASTM D 1415) 3.2.3 Thermal Analysis and Pyrolytic Chromatography Ford Motor Company, at its option, may conduct pyrolytic gas chromatography, thermogravimetric analysis and differential thermal analysis of material/parts supplied t

    10、o this specification. The spectra established for initial approval shall constitute the reference standard and shall be kept on file at designated materials laboratory. All samples shall produce spectra that correspond to the reference standard when tested under the same conditions as those specifie

    11、d on the master spectrum. The infrared spectra of the toluene extractables of the Type III material must be distinguishable from the Type I and Type II spectra. 3.2.4 Additional Requirements Any requirements applicable to specific parts shall be specified on the engineering drawings or in a separate

    12、 engineering specification identified on the drawing. 3.3 INITIAL QUALIFICATION These tests are to be conducted on slab stock by all material suppliers prior to source approval and at least once every 6 months. 3.3.1 Original Properties Type I Type II Type III Hardness, Durometer “A“ 65 - 75 75 - 85

    13、 68 - 78 (ASTM D 2240) Tensile Strength, MPa, min 13.8 13.8 13.8 (ASTM D 412, Die “C“) Elongation, % min 175 225 175 (ASTM D 412, Die “C“) Modulus at 100% 6.6 5.2 6.6 Elongation, MPa, min (ASTM D 412, Die “C“) ENGINEERING MATERIAL SPECIFICATIONESW-M2D247-A Printed copies are uncontrolled Copyright 2

    14、009, Ford Global Technologies, LLC Page 3 of 4 Type I Type II Type III 3.3.2 Heat Aged (ASTM D 865, aluminum block, 168 h at 150 +/- 2 C) Hardness Durometer +5 to +15 0 to +10 +5 to +20 “A“ Change Tensile Strength -15 -40 -75 Change, % max Elongation Change, -70 -70 -90 % max 3.3.3 Immersion in ASTM

    15、 No. 1 Oil (ASTM D 471, aluminum block, 150 +/- 2 C, 70 h for Type I and Type III, 168 h for Type II) Hardness Durometer “A“ Change 0 to +10 0 to +10 0 to +10 Tensile Strength Change, % max -15 -15 -25 Elongation Change, % max -35 -20 -35 Volume Change, % 0 to -10 0 to -10 0 to -10 3.3.4 Immersion i

    16、n ASTM No. 3 Oil (ASTM D 471, aluminum block, 150 +/- 2 C, 70 h for Type I and Type III, 168 h for Type II) Hardness Durometer “A“ Change -10 to 0 -15 to -5 -15 to 0 Tensile Strength Change, % max -30 -30 -40 Elongation Change, % max -35 -20 -40 Volume Change, % 0 to +20 0 to +20 0 to +25 3.3.5 Imme

    17、rsion in Automatic Transmission Fluid, ESP-M2C138-CJ (ASTM D 471, aluminum block, 150 +/- 2 C, 70 h for Type I and Type III, 168 for Type II) Hardness Durometer “A“ Change +/- 5 +/- 5 +/- 5 Tensile Strength Change, % max -50 -50 -50 Elongation Change, % max -50 -50 -50 Volume Change, % 0 to +10 0 to

    18、 +10 0 to +10 ENGINEERING MATERIAL SPECIFICATIONESW-M2D247-A Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 4 of 4 Type I Type II Type III 3.3.6 Low Temperature Pass Pass Pass Brittleness (ASTM D 746, Procedure “B“ non-brittle after 3 min at 32 C) 3.3.7 Low Temper

    19、ature Retraction (TR-10) (ASTM D 1329) Each supplier must establish values for their compound prior to source approval and be able to maintain these values within the given ranges. Unaged Material +/- 1 +/- 1 +/- 1 (as received), C After Oil Aging per +/- 2 +/- 2 +/- 2 Para 3.3.3, C 3.3.8 Compression Set, % max 40 50 40 (ASTM D 395, Method “B“, plied, 70 h at 150 +/- 2 C)


    注意事项

    本文(FORD ESW-M2D247-A-2009 NITRILE BUTADIENE RUBBER HIGH HEAT RESISTANT - OIL SEALS TO BE USED WITH FORD WSS-M99P1111-A 《油封圈用耐高温丁腈橡胶 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(eastlab115)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开