欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD ESF-M4D325-A-2006 NYLON (TYPE 6) COPOLYMER 20% GLASS - MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《20%玻璃增强的尼龙(型号6)共聚物成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    • 资源ID:746240       资源大小:25.92KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD ESF-M4D325-A-2006 NYLON (TYPE 6) COPOLYMER 20% GLASS - MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《20%玻璃增强的尼龙(型号6)共聚物成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 05 04 N-STATUS Replaced by WSS-M4D665-A5 A. Reaume/M. Masserant 2005 01 28 Revised Inserted 3.0; Deleted 3.4, 3.5 & 4 1970 10 22 Released (Was XF-M4DX92) F6Z-435 Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LL

    2、C Page 1 of 2 NYLON (TYPE 6) COPOLYMER, 20% GLASS - MOLDING COMPOUND ESF-M4D325-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a heat stabilized type 6 nylon blended with another polymer to provide a heat sealable, decorable, molded plastic part. This material

    3、 contains approximately 20% glass fiber. 2. APPLICATION This specification was released originally for material used where decorability and/or heat sealability are required such as the horn projector. NOTICE: This material absorbs and retains moisture. Part design and tolerances must accommodate cha

    4、nges in part dimensions and physical properties due to moisture absorption or loss in the service/assembly environment. Information on this material with respect to moisture should be obtained from the responsible PEO Materials Engineering Department. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PR

    5、ODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 CERTIFICATION To be run on a continuing basis. This could be on a lot or daily basis. 3.1.1 Conditioning Specimens are to be dry as molded. They

    6、are not to be intentionally exposed to any moisture. If specimens will be exposed to air for more than 5 min after molding and before testing, they shall be kept in a sealed, air and moisture proof glass container. They shall be tested within 5 min after removal from the containers. Maximum moisture

    7、 content 0.3%. 3.1.2 Melting Point 210 - 225 C (ASTM D 789) 3.1.3 Specific Gravity 1.20 - 1.30 (ASTM D 792) 3.1.4 Moisture Content, max 0.3% (ASTM D 789) 3.1.5 Tensile Strength, min 13,000 psi (90 MPa) (ASTM D 638, Speed “C“) ENGINEERING MATERIAL SPECIFICATIONESF-M4D325-A Printed copies are uncontro

    8、lled Copyright 2006, Ford Global Technologies, LLC Page 2 of 2 3.2 MOLDED TEST SPECIMEN To be run at intervals established by Quality Control to confirm above (para. 3.1) values are representative, and for initial approval. 3.2.1 Impact Strength, Izod, min 0.8 ft lb/in (43 J/m) (ASTM D 256, notched)

    9、 3.2.2 Deflection Temperature, min (ASTM D 648, as received, 1/4 in (6.4 mm) specimen width) At 66 psi (455 kPa) 199 C At 264 psi (1820 kPa) 177 C 3.2.3 Flexural Modulus, min 900,000 psi (6.2 GPa) (ASTM D 790, 1/4 x 1/2 in (6.4 x 12.7 mm) specimen) 3.3 MOLDED PART 3.3.1 Parts molded of this material shall be free from visible porosity and voids. 3.3.2 Melting Point 210 - 225 C (ASTM D 789) 3.3.3 Ductility The performance test method and part requirement shall be specified on the engineering drawing.


    注意事项

    本文(FORD ESF-M4D325-A-2006 NYLON (TYPE 6) COPOLYMER 20% GLASS - MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《20%玻璃增强的尼龙(型号6)共聚物成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(outsidejudge265)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开