欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD ESB-M4D74-A-2008 POLYETHYLENE HIGH DENSITY INJECTION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《高密度聚乙烯注塑成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSG-M4D901-A1 FO.pdf

    • 资源ID:745571       资源大小:33.93KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD ESB-M4D74-A-2008 POLYETHYLENE HIGH DENSITY INJECTION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《高密度聚乙烯注塑成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSG-M4D901-A1 FO.pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2008 02 29 N-STATUS Replaced by WSG-M4D901-A1 G. Kowalski 2005 01 07 Revised Inserted 3.0; Deleted 3.2.13, 3.3 & 4 1963 08 02 Released AS1-1011 Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 1 of 4 POLYETHYL

    2、ENE, HIGH DENSITY ESB-M4D74-A INJECTION MOLDING COMPOUND NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is high density, precolored, polyethylene molding compound. 2. APPLICATION This specification was released originally for materials: Type I Generally used in int

    3、erior applications such as cowl side panels and glove box assemblies, or in under-hood applications such as windshield washer reservoirs. Type II Formulated for maximum resistance to weathering and is color matched or color keyed to body exterior colors. This material is specified for exterior appli

    4、cations such as valance panels where exposure to direct sunlight is minimal. 3. REQUIREMENTS Note: ESB-M4D74 specification without type designation shall denote Type I only. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard

    5、 Requirements For Production Materials (WSS-M99P1111-A). 3.1 RAW MATERIAL (Natural Resin) Type I Type II 3.1.1 Density, g/cm3, min 0.945 0.950 (ASTM D 792) 3.1.2 Flow Rate, g/10 min 20.0 max 10.0 - 20.0 (ASTM D 1238) Note: Flow rate for washer reservoir cap molding resin shall not exceed 5.0 g/10 mi

    6、n. 3.1.3 Melting Point, C min 121 121 (FLTM BO 021-02) ENGINEERING MATERIAL SPECIFICATIONESB-M4D74-APrinted copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 2 of 4 Type I Type II 3.2 MOLDED PART Note: Type II samples shall be prepared from finished parts. 3.2.1 Tensile Stre

    7、ngth, psi (MPa), min 2800 (19.3) 3200 (22.1) (ASTM D 638, Speed “C“) 3.2.2 Elongation, % min 20 100 (ASTM D 638, Speed “C“) 3.2.3 Hardness Durometer “D“, min 60 55 (ASTM D 2240, instantaneous reading) 3.2.4 Impact Strength, Izod, ft lb/in (J/m), min (ASTM D 256, samples impacted perpendicular to flo

    8、w direction) Notched 0.5 (27) 0.5 (27) Unnotched - No break 3.2.5 Heat Resistance (Types I & II) There shall be no visible permanent distortion or color change after the following conditioning: Test Method: The unmounted finished part shall be subjected to 102 +/- 3 C for 3 h in a mechanical convect

    9、ion oven. The test specimen shall be shielded from the direct velocity of high temperature air. Allow part to return to room temperature. 3.2.6 Solvent Resistance (Types I & II) There shall be no visible deleterious effects such as cracking, crazing, color changes, or other surface conditions. Test

    10、Method: Immerse a 1.0 in (25 mm) portion of a sample, 1 x 3 in (25 x 75 mm) in the solvents listed below for 2 h at 23 +/- 2 C. . Petroleum Naphtha M-14J147 . Trichlorethylene ESF-M5B99 . Kerosene M14J132 . Methyl Ethyl Ketone M14J40 3.2.7 Low Temperature Impact Resistance (Type I only) There shall

    11、be no evidence of cracking or any permanent deformation of the assembly. Test Method: Condition the assembly in the cold chamber at -29 C for 5 h. Remove and within 5 s subject sample to impact test by dropping a 2.0 in (50 mm) diameter steel ball weighing 535 g from a height of 4.0 ft (1.22 m). The

    12、 ball shall be directed as nearly as possible to the central portion of the test surface. ENGINEERING MATERIAL SPECIFICATIONESB-M4D74-APrinted copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 3 of 4 3.2.8 Environmental Exposure (Type I only) There shall be no evidence of cr

    13、acking, crazing, distortion, or color change. 3.2.8.1 Test Method (for washer reservoirs only) The container assembly shall be filled to 3/4 volume capacity with 20% commercial windshield washer solution, covered and subjected to 5 complete cycles of the following: . 3 h at 102 +/- 3 C . 5 h at 23 +

    14、/- 2 C . 16 h at -29 C Observations shall be made at the completion of each cycle. 3.2.8.2 Test Method (for other Type I applications) Place a small piece of wood approximately 3 x 3 x 1/2 in (75 x 75 x 13 mm) in intimate contact with a flat portion of the test assembly. Retain by driving a standard

    15、 pan head tapping screw 1/2 x 8-15 threads per inch (52726-S or equivalent) through the test material into the wood block. The assemblies shall be subjected to 5 complete cycles of the following: . 3 h at 102 +/- 3 C . 5 h at 23 +/- 2 C . 16 h at -29 C Observations shall be made at the completion of

    16、 each cycle for any evidence of cracking, crazing, or distortion. 3.2.9 Impact Strength, Gardner (Type II only), min At 23 +/- 2 C 70 in-lb (7.9 J) At -40 C 100 in-lb (11.3 J) Test Method: Condition several sample parts 0.100 - 0.125 in (2.54 - 3.18 mm) thick for 5 h at the desired test temperature.

    17、 Test samples shall be pieces cut from finished (molded-in-color), injection molded parts. A Gardner Impact Unit (model IG-1120) with a 1/2 in (12.7 mm) hemispherical impact head and the corresponding 1/2 in (12.7 mm) diameter steel base plate ring shall be positioned on any minimal energy absorbing

    18、 surface. Test samples shall be impacted within 5 s after removal from the temperature conditioning chamber. 3.2.10 Resistance to Weathering (Type II only) In addition to requirements specified below, samples shall exhibit no more than a 40% decrease in tensile strength after exposure to weathering.

    19、 ENGINEERING MATERIAL SPECIFICATIONESB-M4D74-APrinted copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 4 of 4 3.2.10.1 Weatherometer (FLTM BO 101-01) The material shall not stain, chalk, exhibit color change or change in hue in accordance with rating 4 of AATCC Gray Scale f

    20、or Evaluating Change in Color (10 step) after 1,600 h exposure. 3.2.10.2 Florida Exposure After exposure to Florida weathering (5 South, D.W.I) for 1 year, samples shall not exhibit objectionable color change nor surface degradation. 3.2.11 Appearance The color, pattern, finish, and embossing shall

    21、match that of the master sample as approved for production by the Design Center. Each molded color must pass Resistance to Weathering requirements of para. 3.2.10. 3.2.12 Flammability, max 4 in (101 mm)/min (FLTM BN 024-02, without the lot sampling plan) In addition, the test specimen shall not exhi

    22、bit any flashing or sudden flaming on either surface in excess of the above maximum value. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 MOLD SHRINKAGE 0.015 in/in (mm/mm) (ASTM D 955) 5.2 COEFFICIENT OF LINEAR THERMAL EXPANSION 8 x 10-5/ E (ASTM D 696) (14.4 x 10-5/ C)


    注意事项

    本文(FORD ESB-M4D74-A-2008 POLYETHYLENE HIGH DENSITY INJECTION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《高密度聚乙烯注塑成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSG-M4D901-A1 FO.pdf)为本站会员(赵齐羽)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开