1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R111-96. 96-04-26 Michael A. Frye B Redraw with changes. Update to current requirements. Editorial changes throughout. - gap 06-08-01 Raymond Monnin The original first page of this drawing has been replaced. RE
2、V SHET REV SHET REV STATUS REV B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Tim H. Noh DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Tim H. Noh COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY A
3、LL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, DIGITAL, ECL, OR/NOR GATES, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-02-05 MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-91528 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E327-06 Provided by
4、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91528 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assura
5、nce class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels
6、are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91528 01 M X X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA des
7、ignator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-)
8、indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 100301 Triple 5-input OR/NOR gate 02 100302 Quint 2-input OR/NOR gate 1.2.3 Device class designator. The device class designator is a single l
9、etter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification
10、to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDIP5-T24 or CDIP6-T24 24 dual-in-line Y See figure 1 24 quad flat pack 1.2.5 Lead finish. The lead finish is as specified in
11、MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91528 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISIO
12、N LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Negative supply voltage range (VEE) -7.0 V dc to +0.5 V dc DC input voltage range (VIN) VEEto +0.5 V Maximum dc output current (IOUT) -50 mA Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) . +30
13、0C Junction temperature (TJ) +175C Maximum power dissipation (PD): Device type 01 304 mW Device type 02 453 mW Thermal resistance, junction-to-case (JC): Case X See MIL-STD-1835 Case Y 28C/W 1.4 Recommended operating conditions. Negative supply voltage range (VEE) -5.7 V minimum to -4.2 V maximum Ca
14、se operating temperature range (TC) . -55C to +125C High level input voltage range (VIH) -1.165 V minimum to -0.870 V maximum Low level input voltage range (VIL) . -1.830 V minimum to -1.475 V maximum 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following speci
15、fication, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Sp
16、ecification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawing
17、s. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of
18、this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the devi
19、ce. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91528 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVI
20、SION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in
21、 the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The de
22、sign, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connec
23、tions. The terminal connections shall be as specified on figure 2. 3.2.3 Truth tables. The truth tables shall be as specified on figure 3. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics an
24、d postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table
25、I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the devic
26、e. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark
27、for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 l
28、isted manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance
29、submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Cert
30、ificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class
31、M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to rev
32、iew the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 29 (
33、see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91528 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrica
34、l performance characteristics. Test Symbol Conditions -55C TC +125C Group A subgroupsDevice type Limits Unit unless otherwise specified Min Max High level output voltage VOHVIH= -0.870 V, VEE= -4.2 V, 1, 2 All -1.025 -0.870 V VIL= -1.830 V 3 -1.085 -0.870 Low level output voltage VOLVIH= -0.870 V, V
35、EE= -4.2 V, 1, 2 All -1.830 -1.620 V IL= -1.830 V 3 -1.830 -1.555 High level threshold VOHCVIH= -1.165 V, VEE= -4.2 V, 1, 2 All -1.035 V output voltage VIL= -1.475 V 3 -1.085 Low level threshold VOLCVIH= -1.165 V, VEE= -4.2 V, 1 01 -1.610 V output voltage VIL= -1.475 V 2, 3 -1.555 1, 2 02 -1.610 3 -
36、1.555 High level input current IIHVEE= -5.7 V , 1, 2 All 240 A VIN= -0.870 V 3 340 Low level input current IILVEE= -4.2 V, 1, 2, 3 All 0.5 A IN= -1.830 V Power supply drain IEEInputs open, 1, 2, 3 01 -32 -12 mA current VEE= -5.7 V, -4.2 V 1, 2, 3 02 -48 -17 mA Truth table tests VIH= -1.018 V, 7, 8 A
37、ll IL= -1.652 V, See 4.4.1b Propagation delay time, tPLH1, See figure 4 9 01 0.3 1.5 ns data to output tPHL110 0.3 1.8 11 0.25 1.7 9 02 0.4 1.5 ns 10 0.4 1.7 11 0.3 1.8 Propagation delay time, tPLH2, See figure 4 9 02 0.8 2.3 ns enable to output tPHL210 0.8 2.8 11 0.6 2.6 Transition time, output tTL
38、H, See figure 4 9 All 0.3 1.2 ns tTHL2/ 10 0.3 1.2 11 0.3 1.2 1/ Each input/output, as applicable, shall be tested at the specified temperature for the specified limits. Output terminals shall be terminated through 50 to -2 V. Input terminals not designated shall be high logic level, low logic level
39、, or open. 2/ This parameter is provided as design information only (not tested but guaranteed). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91528 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990
40、REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Case Y Inches 1/ Millimeters 1/ Symbol Min Max Min Max A .085 2.16 b .016 .018 0.41 0.46 c .004 .006 0.10 0.15 D/E .370 .400 2/ 9.40 10.16 2/ e .045 .055 1.14 1.40 L .250 .360 6.35 9.14 Q .035 .050 0.89 1.27 S .075 1.91 N 24 24 NOTE: 1. The U.S. governm
41、ent preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 2. This dimension allows for meniscus and
42、 glass overrun. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91528 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device typ
43、es 01 02 Case outlines X Y X Y Terminal number Terminal symbol 1 D3c D5b D2e D1d 2 D4c D1c Oe D2d 3 D5c D2c eO D1e 4 Oc D3c dO D2e 5 cO D4c Od Oe 6 VCCD5c VCCeO 7 VCCAOc VCCAdO 8 Ob cO cO Od 9 bO VCCOc VCC10 aO VCCAOb VCCA11 Oa ObbO cO 12 D1a bO aO Oc 13 D2a aO Oa Ob 14 D3a Oa D1a bO 15 D4a D1a D2a
44、aO 16 D5a D2a D1b Oa 17 D1b D3a D2b D1a 18 VEED4a VEED2a 19 D2b D5a E D1b 20 D3b D1b D1c D2b 21 D4b VEED2c VEE22 D5b D2b D1d E 23 D1c D3b D2d D1c 24 D2c D4b D1e D2c FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAND
45、ARD MICROCIRCUIT DRAWING SIZE A 5962-91528 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Device type 02 Inputs Outputs Inputs Outputs D1 D2 D3 D4 D5 O O D1 D2 E O O L L L L L L H L L L L H H X X X X H L L H L H L X H X X X H L
46、H L L H L X X H X X H L H H L H L X X X H X H L X X H H L X X X X H H L H = High level L = Low level H = High level X = Irrelevant L = Low level X = Irrelevant FIGURE 3. Truth tables. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRC
47、UIT DRAWING SIZE A 5962-91528 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 NOTES: 1. VCC= +2 V, VEE= -2.5 V. 2. L1 and L2 = equal length 50 impedance lines. 3. RT= 50 terminator internal to scope. 4. Decoupling 0.1 F from GND to VCCand VEE.
48、5. All unused outputs are loaded with 50 to GND. 6. CL= fixture and stray capacitance 3 pF. FIGURE 4. Test circuit and timing waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91528 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 4.
