1、REVISIONS LTR DESCRIPTION DATE APPROVED A Add source 06090. 28 Feb 91 Richard Marbais B Add dimension “Z”. Editorial changes throughout. 22 Sept 93 Randy Larson C Update format. Correcting references. Correcting address list of sources. 16 July 02 Robert Heber Prepared in accordance with ASME Y14.10
2、0 REV PAGE REV C C C C C C REV STATUS OF PAGES PAGE 1 2 3 4 5 6 PREPARED BY PMIC N/A Jeffery Tunstall DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Abdo Abdouni APPROVED BY Robert Heber CONNECTOR, ELECTRICAL, CIRCULAR, PLUG, STRAIGHT, REMOVAL CRIMP CONTACTS, SERIES III,
3、HYBRID CONSTRUCTION SIZE CAGE CODE 037Z3 DWG. NO. 89090 Original date of drawing 21 Sept 89 A REV C PAGE 1 OF 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMSC N/A 5935-E663 DISTRIBUTION STATEMENT A. Approved for public release; distribution is
4、unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89090 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 3 FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction
5、or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89090 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 4 Shell size Shell size code B dia S dia max Z max 9 A .732 .724 .858 1.220 11 B .839 .831 .984 1.220 13 C 1.008 1.000 1.157 1.220 15 D 1.138 1
6、.130 1.280 1.220 17 E 1.276 1.268 1.406 1.220 19 F 1.382 1.374 1.516 1.220 21 G 1.508 1.500 1.642 1.220 23 H 1.626 1.618 1.768 1.220 25 J 1.752 1.744 1.890 1.220 Inches mm Inches mm Inches mm Inches mm .060 1.52 .858 21.79 1.268 32.21 1.516 38.51 .070 1.78 .984 24.99 1.276 32.41 1.618 41.10 .169 4.2
7、9 1.000 25.40 1.280 32.51 1.626 41.30 .201 5.11 1.008 25.60 1.374 34.90 1.642 41.71 .724 18.39 1.130 28.70 1.382 35.10 1.744 44.30 .732 18.59 1.138 28.91 1.406 35.71 1.752 44.50 .831 21.11 1.157 29.39 1.500 38.10 1.768 44.91 .839 21.31 1.220 30.99 1.508 38.30 1.890 48.00 NOTES: 1. Dimensions are inc
8、hes. 2. Metric equivalents are given for general information only. 3. Metallic material inner shell must have solid surface through the length Z and inner circumference of the shell. 4. Undercut may me be incorporated to accept accessory configuration in accordance with MIL-DTL-38999, series III. 5.
9、 For details of connector front and rear end configuration, see MIL-DTL-38999, series III. 6. Metallic surfaces required for conductivity between plug receptacle; plug accessories. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO
10、. 037Z3 89090 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 5 FIGURE 1. Dimensions and configuration Continued. SCOPE This is an extended environment-resisting hybrid construction (metal sleeve in nonmetallic shell) connector. Metallic surfaces indicated on figure 1 are finish
11、ed with olive drab cadmium plate over a suitable underplate. Other surfaces are uncoated nonmetallic for corrosion resistance. REQUIREMENTS: Connectors shall meet the requirements of MIL-DTL-38999, series III, class W, with the following exceptions and additions. Dimension and configurations: See fi
12、gure 1. Interface dimensions shall confirm to MIL-DTL-38999. For insert arrangements: See MIL-STD-1560. Salt spray (corrosion): The wired, assembled connectors shall meet the dynamic salt spray requirements of MIL-DTL-38999, with the following exceptions: The connectors shall be tested 1052 hours ma
13、ted, followed by 48 hours unmated. Hydrolytic stability: Unmated, unwired connectors shall be subjected to the following tests: a. Measure connector weight. b. Boil in distilled water until no further weight gain is observed. c. Connector may be dried with filtered compressed air. d. When connector
14、weight has stabilized, measure percent total weight gain, mating dimensions and length. e. Mate the connector and apply specified coupling torque. f. Inspect the connectors for damage. The connector shall be without defects detrimental to mechanical performance. Total weight gain shall be less than
15、0.75 percent. When subjected to coupling torque values specified in series III, coupling torque of MIL-DTL-38999, there shall be no evidence of cracking, breaking or loosening of parts. Lighting strike: Mated connectors with suitable accessories shall be subjected to a simulated lighting current pul
16、se exposure. The current pulse shall be applied by a suitable high current generator and the current waveform shall be monitored and recorded by a current transformers (or current shunt) and storage oscilloscope. The test pulse shall be a damped sinusoid with a basic frequency of 21 kHz and an ampli
17、tude decay time of 140 microseconds to 37 percent of its peak value. Pulse amplitude shall be 60 kA. The receptacle connector shall be mounted on a simulated panel, using its normal mounting provisions. The simulated current pulse shall be applied between the plug accessory and the receptacle mounti
18、ng panel. Upon completion of the pulse application, and without disturbing the test sample, the shell-to-shell conductivity test of MIL-DTL-38999 shall be performed. When the test electrical measurements have been completed, the Provided by IHSNot for ResaleNo reproduction or networking permitted wi
19、thout license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89090 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 6 sample shall be inspected in both the mated and unmated condition for evidence of damage from the simulated lighting current pulse. Part or Identifying Number (PIN): T
20、he PIN shall be in accordance with the following: 89090- 11- 35 P N DSCC drawing number Shell size Insert arrangement Contact style Polarizing position Marking: Marking shall be accordance with MIL-DTL-38999 except the PIN shall be as stated above. Application guidance: To obtain full extended perfo
21、rmance as specified above, this connector must be assembled with the applicable accessory backshell and mated with a hybrid counterpart receptacle. QUALIFICATION: Qualification inspection: Qualification inspection for the connectors specified herein shall not be required. Quality conformance inspect
22、ion: Shall be in accordance with MIL-DTL-38999. Inspection of packaging: Shall be in accordance with MIL-DTL-38999. Method of inspection: Shall be in accordance with MIL-DTL -38999. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG N
23、O. 037Z3 89090 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV C PAGE 7 Approved sources of supply. Approved sources are listed herein. Additional sources will be added as they become available. The vendors listed herein have agreed to this drawing and a certificate of compliance has b
24、een submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ Replacement military specification PIN 89090 64600 G3G6P* N/A 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. 2/ Do not use this number for item acquisit
25、ion. Items acquired to this may not satisfy the performance requirements of this drawing. Vendor CAGE Vendor name number and address 64600 G & H Technology 740 West Ventura Boulevard Camarillo, CA 93010 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
