1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Page 14, add new paragraph 6.5: Patents 24 Oct 85 I. R. Jones B Add three more configurations to drawing. Changed material paragraph. Editorial changes throughout. 31 Aug 87 D. E. Morgan C Changed location of M/2 dimension on configurations E and F of figur
2、e 1. Editorial changes throughout 29 Dec 87 Randy Larson D Changed center hole in configurations D and E of figure 1. Updated vendor addresses. Editorial changes throughout. 15 Dec 88 Randy Larson E Changes in accordance with Notice of Revision 5998-R001-95. 14 Nov 94 John F. Raye F Inactivate for n
3、ew design materials contained herein. Add supersession table to section six. Change FSC from 5999 to 5998. Editorial changes throughout. 19 Dec 97 Monica L. Poelking G Removed references to superseded documents, updated vendor contact information, added environmentally preferable material paragraph,
4、 and editorial changes throughout. 04 Jun 04 Thomas M. Hess Prepared in accordance with ASME Y14.100 Selected item drawing REV G G G G G G G PAGE 18 19 20 21 22 23 24 REV STATUS REV G G G G G G G G G G G G G G G G G OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PMIC N/A PREPARED BY Bernar
5、d J. Miesse DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 http:/www.dscc.dla.mil Original date of drawing 7 June 1985 CHECKED BY David J. Corbett TITLE: HOLDER, ELECTRICAL CARD, CARD GUIDE, APPROVED BY Monica L. Poelking METAL, WITHOUT FLARED ENTRY SIZE A CODE IDENT. NO. 14
6、933 DWG NO. 85020 REV G PAGE 1 OF 24 AMSC N/A 5998-E048 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INACTIVE FOR NEW DESIGN AFTER 19 DECEMBER 1997 Device types contained herein are inactive for new design. FOR NEW DESIGN USE CID A-A-55563. CURRENT DESIGN ACTIVITY
7、 CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85020 REV G PAGE 2 1
8、. SCOPE 1.1 Scope. This drawing describes the requirements for a family of card holders intended for use on printed circuit boards. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85020 Drawing number 216 Dash number (see table I) N Finish (C, N, or blank) (see 3.3) 2. AP
9、PLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitati
10、on or contract (see 6.2). DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Bui
11、lding 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract (see 6.2). AMERICAN SOCIETY FOR TESTIN
12、G AND MATERIALS (ASTM) ASTM-A366/A366M Steel Sheets, Carbon, Cold Rolled. ASTM-A967 Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts. ASTM-B194 Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar (UNS C1700 and C17200). (Application for copies should be add
13、ressed to the ASTM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or at URL http:/www.astm.org.) SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE AMS 5517J Steel, Corrosion Resistant, Sheet and Strip (UNS S30100) SAE AMS-QQ-N-290 Nickel Plating (Electrodeposited). SAE A
14、MS-QQ-P-416 Plating, Cadmium (Electrodeposited). (Application for copies should be addressed to the SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or at URL http:/www.sae.org.) (Industry association specifications and standards are generally available for reference from li
15、braries. They are also distributed among technical groups and using Federal agencies.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes appl
16、icable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85020 REV G PAGE 3 3. REQUIREMENTS 3.1 Inter
17、face and physical dimensions. See figure 1 and table I. 3.2 Material. Material shall be as specified in table I. Beryllium copper shall be in accordance with ASTM-B194. Steel shall be in accordance with ASTM-A366/A366M (NOTE: Stainless steel in accordance with SAE AMS 5517J (UNS C30100) may be used
18、in lieu of steel). For configurations A, B, D, and E, the material thickness shall be .008 .002 inch (0.20 0.05 mm). For configurations C and F, the material thickness shall be .005 .001 inch (0.13 0.03 mm). Parts constructed of BH material (see table I) shall have an additional one-quarter heat tre
19、at in accordance with ASTM-B194. 3.3 Finish. Card holders constructed of beryllium copper or steel shall be finished with either cadmium plate in accordance with SAE AMS-QQ-P-416, type II, class 2 or nickel plate in accordance with SAE AMS-QQ-N-290, class 1, grade G (bright). Card holders with a cad
20、mium plated finish shall include a suffix “C” and card holders with a nickel plated finish shall include a suffix “N” (see 1.2). Card holders constructed of stainless steel shall be passivated in accordance with ASTM-A967 (Nitric 2). No finish suffix is needed for passivated stainless steel card hol
21、ders and the finish suffix in the PIN shall be left blank. 3.4 DSCC certificate of compliance. A certificate of compliance shall be submitted to DSCC-VAC by each manufacturer desiring to be listed as a suggested source of supply (see 6.7). The certificate shall state that the manufacturers product m
22、eets all the requirements of this drawing. 3.4.1 Optional statement of compliance in lieu of testing. The acquiring activity, at its discretion, may accept from the manufacturer a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery tests (see 4.1.2 a
23、nd 6.2.c). 3.5 Marking. Marking of the card holder is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.6 Recycled,
24、recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle c
25、osts. 3.7 Workmanship. Holders shall be processed in such a manner as to be uniform in quality and shall be free from surface and finish flaws that could affect life or serviceability. Finish shall be smooth and edges shall be rounded. Chipping, cracking, deterioration, disintegration, or burrs are
26、unacceptable. Configuration A FIGURE 1. Dimensions and configurations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85020 REV G PAGE 4 Configuration B Configuration
27、 C Configuration D FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85020 REV G PAGE 5 Configuration E Configuratio
28、n F Inches mm Inches mm Inches Mm Inches mm Inches Mm .001 .003 .005 .010 .02 0.03 0.08 0.13 0.25 0.5 .067 .070 .093 .105 .12 1.70 1.78 2.36 2.67 3.0 .125 .141 .148 .16 .18 3.18 3.58 3.76 4.1 4.6 .198 .25 .250 .27 .30 5.03 6.4 6.35 6.86 7.6 .31 .33 .37 .500 .52 7.9 8.4 9.4 12.7 13.2 NOTES: 1. Dimens
29、ions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .02 (0.5 mm) on two place decimals and .010 (0.25 mm) on three place decimals. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduc
30、tion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85020 REV G PAGE 6 TABLE I. Dash numbers. Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel Length (inches) L
31、Board slot thickness .005 (0.13 mm) A = .0312 (0.79 mm) B = .0625 (1.59 mm) C = .0937 (2.38 mm) Configuration 001* B 2.0 (50.8 mm) A A 002* BH 2.0 (50.8 mm) A D 003* S 2.0 (50.8 mm) A A 004* B 2.0 (50.8 mm) B A 005* BH 2.0 (50.8 mm) B D 006* S 2.0 (50.8 mm) B A 007* B 2.0 (50.8 mm) C A 008* BH 2.0 (
32、50.8 mm) C D 009* S 2.0 (50.8 mm) C A 010* B 2.0 (50.8 mm) A B 011* BH 2.0 (50.8 mm) A E 012* S 2.0 (50.8 mm) A B 013* B 2.0 (50.8 mm) B B 014* BH 2.0 (50.8 mm) B E 015* S 2.0 (50.8 mm) B B 016* B 2.0 (50.8 mm) C B 017* BH 2.0 (50.8 mm) C E 018* S 2.0 (50.8 mm) C B 019* B 2.0 (50.8 mm) A C 020* BH 2
33、.0 (50.8 mm) A F 021* S 2.0 (50.8 mm) A C 022* B 2.0 (50.8 mm) B C 023* BH 2.0 (50.8 mm) B F 024* S 2.0 (50.8 mm) B C 025* B 2.5 (63.5 mm) A A 026* BH 2.5 (63.5 mm) A D 027* S 2.5 (63.5 mm) A A 028* B 2.5 (63.5 mm) B A 029* BH 2.5 (63.5 mm) B D 030* S 2.5 (63.5 mm) B A 031* B 2.5 (63.5 mm) C A 032*
34、BH 2.5 (63.5 mm) C D 033* S 2.5 (63.5 mm) C A See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85020 REV G PAGE 7 TABLE I. Dash numbers -
35、Continued. Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel Length (inches) L Board slot thickness .005 (0.13 mm) A = .0312 (0.79 mm) B = .0625 (1.59 mm) C = .0937 (2.38 mm) Configuration 034* B 2.5 (63.5 mm) A B 035* BH 2.5 (63.5 mm) A E 036* S 2.5
36、(63.5 mm) A B 037* B 2.5 (63.5 mm) B B 038* BH 2.5 (63.5 mm) B E 039* S 2.5 (63.5 mm) B B 040* B 2.5 (63.5 mm) C B 041* BH 2.5 (63.5 mm) C E 042* S 2.5 (63.5 mm) C B 043* B 2.5 (63.5 mm) A C 044* BH 2.5 (63.5 mm) A F 045* S 2.5 (63.5 mm) A C 046* B 2.5 (63.5 mm) B C 047* BH 2.5 (63.5 mm) B F 048* S
37、2.5 (63.5 mm) B C 049* B 3.0 (76.2 mm) A A 050* BH 3.0 (76.2 mm) A D 051* S 3.0 (76.2 mm) A A 052* B 3.0 (76.2 mm) B A 053* BH 3.0 (76.2 mm) B D 054* S 3.0 (76.2 mm) B A 055* B 3.0 (76.2 mm) C A 056* BH 3.0 (76.2 mm) C D 057* S 3.0 (76.2 mm) C A 058* B 3.0 (76.2 mm) A B 059* BH 3.0 (76.2 mm) A E 060
38、* S 3.0 (76.2 mm) A B 061* B 3.0 (76.2 mm) B B 062* BH 3.0 (76.2 mm) B E 063* S 3.0 (76.2 mm) B B 064* B 3.0 (76.2 mm) C B 065* BH 3.0 (76.2 mm) C E 066* S 3.0 (76.2 mm) C B See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
39、,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85020 REV G PAGE 8 TABLE I. Dash numbers - Continued. Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel Length (inches) L Board slot thickness .005 (0.13 mm) A = .031
40、2 (0.79 mm) B = .0625 (1.59 mm) C = .0937 (2.38 mm) Configuration 067* B 3.0 (76.2 mm) A C 068* BH 3.0 (76.2 mm) A F 069* S 3.0 (76.2 mm) A C 070* B 3.0 (76.2 mm) B C 071* BH 3.0 (76.2 mm) B F 072* S 3.0 (76.2 mm) B C 073* B 3.5 (88.9 mm) A A 074* BH 3.5 (88.9 mm) A D 075* S 3.5 (88.9 mm) A A 076* B
41、 3.5 (88.9 mm) B A 077* BH 3.5 (88.9 mm) B D 078* S 3.5 (88.9 mm) B A 079* B 3.5 (88.9 mm) C A 080* BH 3.5 (88.9 mm) C D 081* S 3.5 (88.9 mm) C A 082* B 3.5 (88.9 mm) A B 083* BH 3.5 (88.9 mm) A E 084* S 3.5 (88.9 mm) A B 085* B 3.5 (88.9 mm) B B 086* BH 3.5 (88.9 mm) B E 087* S 3.5 (88.9 mm) B B 08
42、8* B 3.5 (88.9 mm) C B 089* BH 3.5 (88.9 mm) C E 090* S 3.5 (88.9 mm) C B 091* B 3.5 (88.9 mm) A C 092* BH 3.5 (88.9 mm) A F 093* S 3.5 (88.9 mm) A C 094* B 3.5 (88.9 mm) B C 095* BH 3.5 (88.9 mm) B F 096* S 3.5 (88.9 mm) B C 097* B 4.0 (101.6 mm) A A 098* BH 4.0 (101.6 mm) A D 099* S 4.0 (101.6 mm)
43、 A A See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85020 REV G PAGE 9 TABLE I. Dash numbers - Continued. Dash number 1/ Material B Bery
44、llium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel Length (inches) L Board slot thickness .005 (0.13 mm) A = .0312 (0.79 mm) B = .0625 (1.59 mm) C = .0937 (2.38 mm) Configuration 100* B 4.0 (101.6 mm) B A 101* BH 4.0 (101.6 mm) B D 102* S 4.0 (101.6 mm) B A 103* B 4.0 (101.6 mm) C
45、A 104* BH 4.0 (101.6 mm) C D 105* S 4.0 (101.6 mm) C A 106* B 4.0 (101.6 mm) A B 107* BH 4.0 (101.6 mm) A E 108* S 4.0 (101.6 mm) A B 109* B 4.0 (101.6 mm) B B 110* BH 4.0 (101.6 mm) B E 111* S 4.0 (101.6 mm) B B 112* B 4.0 (101.6 mm) C B 113* BH 4.0 (101.6 mm) C E 114* S 4.0 (101.6 mm) C B 115* B 4
46、.0 (101.6 mm) A C 116* BH 4.0 (101.6 mm) A F 117* S 4.0 (101.6 mm) A C 118* B 4.0 (101.6 mm) B C 119* BH 4.0 (101.6 mm) B F 120* S 4.0 (101.6 mm) B C 121* B 4.5 (114.3 mm) A A 122* BH 4.5 (114.3 mm) A D 123* S 4.5 (114.3 mm) A A 124* B 4.5 (114.3 mm) B A 125* BH 4.5 (114.3 mm) B D 126* S 4.5 (114.3
47、mm) B A 127* B 4.5 (114.3 mm) C A 128* BH 4.5 (114.3 mm) C D 129* S 4.5 (114.3 mm) C A 130* B 4.5 (114.3 mm) A B 131* BH 4.5 (114.3 mm) A E 132* S 4.5 (114.3 mm) A B See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENS
48、E SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85020 REV G PAGE 10 TABLE I. Dash numbers - Continued. Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel Length (inches) L Board slot thickness .005 (0.13 mm) A = .0312 (0.79 mm) B = .0625 (1.59 mm) C = .0937 (2.38 mm) Configuration 133* B 4.5 (114.3 mm) B B 134* BH 4.5 (114.3 mm) B E 135* S 4.5 (114.3 mm) B B 136* B 4.5 (114.3 mm) C B 137* BH 4.5 (114.3 mm) C E 138* S 4.5 (114.3 mm) C B 139* B 4.5 (114.3 mm
