欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM E1802-2007 Standard Test Methods for Wet Insulation Integrity Testing of Photovoltaic Modules《光电模件的隔湿完整性测试用标准试验方法》.pdf

    • 资源ID:529500       资源大小:61.25KB        全文页数:3页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM E1802-2007 Standard Test Methods for Wet Insulation Integrity Testing of Photovoltaic Modules《光电模件的隔湿完整性测试用标准试验方法》.pdf

    1、Designation: E 1802 07Standard Test Methods forWet Insulation Integrity Testing of Photovoltaic Modules1This standard is issued under the fixed designation E 1802; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last re

    2、vision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 These test methods provide procedures to determine theinsulation resistance of a photovoltaic (PV) module, i.e. theelectrica

    3、l resistance between the modules internal electricalcomponents and its exposed, electrically conductive, non-current carrying parts and surfaces.1.2 The insulation integrity procedures are a combination ofwet insulation resistance and wet dielectric voltage withstandtest procedures.1.3 These procedu

    4、res are similar to and reference theinsulation integrity test procedures described in Test MethodsE 1462, with the difference being that the photovoltaic moduleunder test is immersed in a wetting solution during theprocedures.1.4 These test methods do not establish pass or fail levels.The determinat

    5、ion of acceptable or unacceptable results isbeyond the scope of these test methods.1.5 The values stated in SI units are to be regarded as thestandard.1.6 There is no similar or equivalent ISO standard.1.7 This standard does not purport to address all of thesafety concerns, if any, associated with i

    6、ts use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For specificprecautionary statements, see Section 6.2. Referenced Documents2.1 ASTM Standards:2E 772 Terminology

    7、 Relating to Solar Energy ConversionE 1328 Terminology Relating to Photovoltaic Solar EnergyConversionE 1462 Test Methods for Insulation Integrity and GroundPath Continuity of Photovoltaic Modules3. Terminology3.1 Definitions Definitions of terms used in this testmethod may be found in Terminology E

    8、 772 and TerminologyE 1328.3.2 Definitions of Terms Specific to This Standard:3.2.1 insulation resistancethe electrical resistance of aphotovoltaic modules insulation, measured between the pho-tovoltaic circuit and exposed, electrically conductive non-current-carrying parts and surfaces of the modul

    9、e.4. Significance and Use4.1 The design of a photovoltaic module or system intendedto provide safe conversion of the suns radiant energy intouseful electricity must take into consideration the possibility ofhazard should the user come into contact with the electricalpotential of the module or system

    10、. In addition, the insulationsystem provides a barrier to electrochemical corrosion, andinsulation flaws can result in increased corrosion and reliabilityproblems. These test methods describe procedures for verify-ing that the design and construction of the module providesadequate electrical isolati

    11、on through normal installation anduse. At no location on the module should the PV generatedelectrical potential be accessible, with the obvious exception ofthe output leads. This isolation is necessary to provide for safeand reliable installation, use, and service of the photovoltaicsystem.4.2 This

    12、test method describes a procedure for determiningthe ability of the module to provide protection from electricalhazards. Its primary use is to find insulation flaws that could bedangerous to persons who may come into contact with themodule, especially when modules are wet. For example, theseflaws co

    13、uld be small holes in the encapsulation that allowhazardous voltages to be accessible on the outside surface of amodule after a period of high humidity.4.3 Insulation flaws in a module may only become detect-able after the module has been wet for a certain period of time.For this reason, these proce

    14、dures specify a minimum time amodule must be immersed prior to the insulation integritymeasurements.4.4 Electrical junction boxes attached to modules are oftendesigned to allow liquid water, accumulated from condensedwater vapor, to drain. Such drain paths are usually designed topermit water to exit

    15、, but not to allow impinging water from rain1These test methods are under the jurisdiction of ASTM Committee E44 onSolar, Geothermal and Other Alternative Energy Sources and are the directresponsibility of Subcommittee E44.09 on Photovoltaic Electric Power Conversion.Current edition approved March 1

    16、, 2007. Published April 2007. Originallyapproved in 1996. Last previous edition approved in 2001 as E 1802 01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the st

    17、andards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.or water sprinklers to enter. It is important that all surfaces ofjunction boxes be thoroughly wetted by spraying during thetests to ena

    18、ble these protective drain features to be properlytested. Therefore, drain holes should not be plugged or other-wise protected.4.5 These procedures may be specified as part of a series ofqualification tests involving performance measurements anddemonstration of functional requirements. Because insul

    19、ationleakage resistance and insulation current leakage are strongfunctions of module dimensions, ambient relative humidity,absorbed water vapor and other factors, it is the responsibilityof the user of these test methods to specify the minimumacceptable leakage resistance.5. Apparatus5.1 In addition

    20、 to the apparatus required for the insulationintegrity measurements of Test Methods E 1462, the followingapparatus is required:5.1.1 Wetting SolutionA solution of tap water and awetting agent3, with a surface tension of 0.03 N/m or less at 226 3C.5.1.2 Immersion Tray A tray containing the wetting so

    21、lu-tion (see 5.1.1) into which the test module is immersed duringthe integrity measurements. The tray must be deep enough tocompletely immerse the laminate portion of the module, andany mating connectors (if used) in the wetting solution.NOTE 1This requirement does not imply that any electrical junc

    22、tionboxes attached to the module must also be immersed.6. Hazards6.1 The electrical measurements used to determine theinsulation integrity require applying a high voltage between atest module and a wetting solution (see 5.1.1). Therefore, inaddition to the high voltage hazard, additional hazards may

    23、exist due to unforeseen conductive paths between the high-voltage source and operators of the test through any spilledwetting solution.7. Procedure7.1 Assemble the required equipment and prepare the wet-ting solution.7.1.1 If both the dielectric voltage withstand and insulationresistance procedures

    24、are to be performed, the tests may beperformed sequentially during a single immersion if theminimum and maximum soak time requirement of 7.2.9 is met.7.2 Dielectric Voltage Withstand Procedure:7.2.1 Unless already provided, connect output leads to themodule in accordance with the wiring method speci

    25、fied by themodule manufacturer. If more than one method is specified, usethe method least likely to restrict water entrance. Seal anythreaded openings intended to terminate electrical conduit,unless the threaded openings are selected as the most likely toallow entrance of water.7.2.2 Short the outpu

    26、t leads of the test module.7.2.3 Place the test module face down in the immersion tray,with the output leads held out of the immersion tray.7.2.4 Add the wetting solution to the immersion tray suchthat the front and back surfaces of the module are completelysubmerged. For framed modules, it may be n

    27、ecessary to pourwetting solution directly onto the back surface. The interfacebetween the back surface and any leads or junction boxes mustbe completely submerged, but maintain the wetting solutionlevel below any junction box covers and vents in the junctionboxes (see 4.4). If mating connectors are

    28、part of the moduledesign, the connectors must be immersed.7.2.5 Wet any unsubmerged surfaces of the module byspraying with the wetting solution.7.2.6 Ensure that the variable d-c voltage power supply isturned off before any electrical connections are made.7.2.7 Connect the ungrounded output of the p

    29、ower supply tothe module output leads.7.2.8 Place the grounded output of the power supply in thewetting solution.7.2.9 Maintain the wetted condition of the module (see 7.2.4and 7.2.5) for a minimum of 2 min and a maximum of 10 min.7.2.10 Test the module for current leakage using the proce-dure in 7.

    30、1.6 through 7.1.9 of Test Methods E 1462.7.2.11 Turn off the power supply.7.2.12 Disconnect the test module.7.2.13 Remove the module from the immersion tray.7.3 Insulation Resistance Procedure:7.3.1 If the insulation resistance test is not performedsequentially with the dielectric voltage withstand

    31、test (see 7.1),prepare the module for the insulation resistance test using7.2.1-7.2.9 of the dielectric voltage withstand procedure.7.3.2 Measure and record the minimum insulation resis-tance according to 7.2 of Test Methods E 1462, using a voltageof 500 V or the rated system voltage, whichever is g

    32、reater,between the shorted module leads and the wetting solution.7.3.3 Turn off the power supply.7.3.4 Disconnect the test module.7.3.5 Remove the module from the immersion tray.8. Report8.1 The report shall include the following items as aminimum:8.1.1 Module manufacturer and complete test specimen

    33、identification.8.1.2 Description of module construction.8.1.3 Description of electrical measurement equipment, andmeasurement conditions or parameters, including total immer-sion time in the wetting solution.8.1.4 Results of the dielectric voltage withstand test asrequired by 8.1.5 of Test Methods E

    34、 1462.8.1.5 Results of the insulation resistance test as required by8.1.7 of Test Methods E 1462.8.1.6 A description of any apparent changes as a result ofthe testing.8.1.7 Observations or indications of any shorting, arcing, orother failures.3An acceptable wetting solution is 1 part Liqui-nox deter

    35、gent in 500 parts waterby volume.The sole source of supply of Liqui-Nox known to the committee at this time isAlconox, Inc., 9T East 40th St., New York, NY, 10016; as part number C6308-2. Ifyou are aware of alternative suppliers, please provide this information to ASTMInternational Headquarters. You

    36、r comments will receive careful consideration at ameeting of the responsible technical committee,1which you may attend.E18020728.1.8 Identification of areas of the module where problemswere found.8.1.9 Any deviations from the standard test procedures.9. Precision and Bias9.1 Because this test method

    37、 uses the insulation integrityprocedures of Test Methods E 1462, the determination ofprecision and bias is not practicable, for the same reasonsstated in Test Methods E 1462.10. Keywords10.1 dielectric voltage withstand; electrical testing; energy;insulation integrity; insulation resistance; modules

    38、; photovol-taics; solarASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringem

    39、ent of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or

    40、 for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views kn

    41、own to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).E1802073


    注意事项

    本文(ASTM E1802-2007 Standard Test Methods for Wet Insulation Integrity Testing of Photovoltaic Modules《光电模件的隔湿完整性测试用标准试验方法》.pdf)为本站会员(testyield361)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开