欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D4780-2012 Standard Test Method for Determination of Low Surface Area of Catalysts and Catalyst Carriers by Multipoint Krypton Adsorption《用多点氪吸附法测定催化剂及催化剂载体的低表面面积的标准试验方法》.pdf

    • 资源ID:517957       资源大小:100.80KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D4780-2012 Standard Test Method for Determination of Low Surface Area of Catalysts and Catalyst Carriers by Multipoint Krypton Adsorption《用多点氪吸附法测定催化剂及催化剂载体的低表面面积的标准试验方法》.pdf

    1、Designation: D4780 12Standard Test Method forDetermination of Low Surface Area of Catalysts andCatalyst Carriers by Multipoint Krypton Adsorption1This standard is issued under the fixed designation D4780; the number immediately following the designation indicates the year oforiginal adoption or, in

    2、the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the specificsurface area of catalysts a

    3、nd catalyst carriers in the range from0.05 to 10 m2/g. A volumetric measuring system is used toobtain at least three data points which fall within the linear BETregion.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This

    4、 standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents

    5、2.1 ASTM Standards:2D3663 Test Method for Surface Area of Catalysts andCatalyst CarriersD3766 Terminology Relating to Catalysts and CatalysisE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE456 Terminology Relating to Quality and StatisticsE691 Practice for Conducting an Int

    6、erlaboratory Study toDetermine the Precision of a Test Method3. Terminology3.1 DefinitionsConsult Terminology D3766.3.2 Symbols:PH1= initial helium pressure, torr.PH2= helium pressure after equilibration, torr.TH1= temperature of manifold at initial heliumpressure, C.TH2= temperature of manifold aft

    7、er equilibration,C.P1= initial Kr pressure, torr.T81= manifold temperature at initial Kr pressure,K.T1= manifold temperature at initial Kr pressure,C.P2= Kr pressure after equilibration, torr.T82= manifold temperature at P2,K.T2= manifold temperature at P2, C.Po,N= liquid nitrogen vapor pressure, to

    8、rr.Po,krypton= calculated krypton vapor pressure, torr.T8s= liquid nitrogen temperature, K.X = relative pressure, P2/Po,krypton.Vd= volume of manifold, cm3.Vs= the apparent dead-space volume, cm3.Ws= weight of sample, g.W1= tare weight of sample tube, g.W2= weight of sample plus tare weight of tube,

    9、 g.Vds= volume of krypton in the dead space, cm.3V1= See 11.3.5.V2= See 11.3.6.Vt= See 11.3.7.Va= See 11.3.9.Vm= See 11.6.4. Summary of Test Method4.1 A catalyst or catalyst carrier sample is degassed byheating in vacuum to remove absorbed vapors from thesurface. The quantity of krypton adsorbed at

    10、various lowpressure levels is determined by measuring pressure differen-tials after introduction of a fixed volume of krypton to thesample at liquid nitrogen temperature.The specific surface areais then calculated from the sample weight and adsorption datausing the BET equation.5. Significance and U

    11、se5.1 This test method has been found useful for the determi-nation of the specific surface area of catalysts and catalystcarriers in the range from 0.05 to 10 m2/g for materials1This test method is under the jurisdiction of ASTM Committee D32 onCatalysts and is the direct responsibility of Subcommi

    12、ttee D32.01 on Physical-Chemical Properties.Current edition approved May 1, 2012. Published July 2012. Originally approvedin 1988. Last previous edition approved in 2007 as D478095(2007). DOI:10.1520/D4780-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Custom

    13、er Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.specification, manufacturing control,

    14、 and research and devel-opment in the evaluation of catalysts. The determination ofsurface area of catalysts and catalyst carriers above 10 m2/g isaddressed in Test Method D3663.6. Apparatus6.1 Aschematic diagram of the apparatus is shown in Fig. 1.It may be constructed of glass or of metal and may

    15、operatemanually or automatically. It has the following features:6.1.1 Vacuum System, capable of attaining pressures below10-4torr (1 torr = 133.3 Pa). This will include a vacuum gage(not shown in Fig. 1). Access to the distribution manifold isthrough the valve V.6.1.2 Distribution Manifold, having a

    16、 volume between 5and 40 cm3(Vd) known to the nearest 0.01 cm3. This volume isdefined as the volume between the stopcocks or valves and itincludes the volume within the pressure gage.6.1.3 Constant Volume Gages, capable of measuring 1 to 10torr to the nearest 0.001 torr and 0 to 1000 torr to the near

    17、esttorr (1 torr = 133.3 Pa).6.1.4 Valve (H), from the helium supply to the distributionmanifold.6.1.5 Valve (K), from the krypton supply to the distributionmanifold.6.1.6 Sample Tube(s), with volume between 5 cm3and 25cm3, depending on the application. The sample tube(s) may beconnected to the distr

    18、ibution manifold with standard taperjoints, glass-to-glass seals, or compression fittings.NOTE 1Modern commercial instruments may employ simple tubeswith volumes outside of this range, and may be capable of testing multiplesamples simultaneously rather than separately as stated in 9.1.6.1.7 Dewar Fl

    19、ask(s) for immersion of the sample tube(s)in liquid nitrogen. The nitrogen level should be fixed at aconstant height by means of an automatic level controller ormanually refilled to a predetermined mark on the sampletube(s) about 30 to 50 mm below the distribution manifoldconnectors.6.1.8 Thermomete

    20、r for measuring the temperature of thedistribution manifold (T1(i)orT2(i) in degrees Celsius. (Al-ternatively, the distribution manifold may be thermostatted afew degrees above ambient to obviate the necessity of record-ing this temperature.)6.1.9 Heating Mantle(s) or Small Furnace(s) for eachsample

    21、 tube to allow outgassing samples at elevated tempera-tures.6.1.10 Laboratory Balance with 0.1 mg (107kg) sensitiv-ity.6.1.11 Thermometer for measuring the temperature of theliquid nitrogen bath (T8s(i) in kelvins. This will preferably bea nitrogen vapor-pressure-thermometer that gives Po,Ndirectlya

    22、nd has greater precision, or a resistance thermometer fromwhich Po,Nvalues may be derived.7. Reagents7.1 Purity of ReagentsReagent grade chemicals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytica

    23、l Reagents of the American Chemical Society,where such specifications are available.3Other grades may beused, provided it is first ascertained that the reagent is ofsufficiently high purity to permit its use without lessening theaccuracy of the determination.7.2 Helium Gas, at least 99.9 % pure.7.3

    24、Krypton Gas, at least 99.9 % pure.7.4 Liquid Nitrogen, of such purity that the saturation vaporpressure Po,Nis not more than 20 torr above barometricpressure. A fresh daily supply is recommended.8. ProcedureSample Preparation and Degassing8.1 Select a sample tube of the desired size. A 5 cm3tube isp

    25、referred for small samples to minimize dead space. However,larger tubes may be required for larger samples or for finelypowdered samples, to avoid percolation of the powder whendegassing is started.8.2 Evacuate the sample tube and then fill to atmosphericpressure with helium. This may be done on the

    26、 surface areaunit, or on a separate piece of equipment.8.3 Remove the sample tube, cap, and weigh. Record theweight as W1.8.4 Place the sample, whose weight is known approxi-mately, into the sample tube. If possible, choose the samplesize to provide an estimated total surface area of 1 to 5 m2.8.5 A

    27、ttach the sample tube to the apparatus. If other samplesare to be run, attach them at this time to the other ports.8.6 Open the S valves where there are samples.8.7 Slowly open the V valve, monitoring the rate of pressuredecrease to avoid too high a rate, which might lead to excessivefluidization of

    28、 powdered samples.8.7.1 If a diffusion pump is used, it may be necessary toclose the V valve system periodically to protect the diffusionpump fluid from exposure to pressures above 0.1 torr forperiods of more than 30 s. Close the valve off for 2 min eachtime.8.8 Install a heating mantle or furnace a

    29、round each sampleand raise the temperature to about 300C (573 K). (WarningTake special precautions if the moisture content exceedsapproximately 5 % to avoid “bumping” of powdered catalyst,3Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For Sugg

    30、estions on the testing of reagents notlisted by the American Chemical Society, see Annual Standards for LaboratoryChemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,MD.FIG. 1 Schematic Diagram of S

    31、urface Area ApparatusD4780 122and to avoid surface area loss by self-steaming. It is recom-mended that the heating rate not exceed 100 K/h under thesecircumstances.)8.9 Continue degassing at about 300C (573 K) for aminimum of 3 h, at a pressure not to exceed 103torr.Overnight degassing is permissibl

    32、e.NOTE 2Certain materials decompose or sinter at 300C. Lowerdegassing temperatures are permissible for such materials; however, thedegassing temperature should be specified when reporting the results.8.10 Remove the heating mantles, and allow the samples tocool.8.11 Close the S valves.8.12 It is per

    33、missible to exercise the option of preliminarydegassing on an external unit. In such a case, follow theprocedures of 8.4-8.11 and then repeat on the adsorption unit,except that the degassing on the adsorption unit can be at roomtemperature and need not exceed 1 h.8.13 If it is desired to weigh the s

    34、ample after preliminarydegassing on an external unit, backfill with helium to slightlyabove atmospheric pressure. Close the S valve.8.13.1 Detach the sample tube from the apparatus, recapwith the stopper used previously, and weigh. Record the weightas W2.8.13.2 Reattach the sample tube to the appara

    35、tus. Removethe backfilled gas by evacuation to less than 103torr at roomtemperature. This should normally take 5 to 10 min.9. ProcedureDead-Space Determination9.1 From this point on, each sample being tested for kryptonadsorption shall be run on an individual basis. Thus, 9.1-10.12shall be carried o

    36、ut separately for each tube in test.9.2 The dead space is the void volume of the chargedsample tube, including the volume within the S valve, when thetube is immersed in liquid nitrogen to the proper depth.9.3 Place a Dewar flask of liquid nitrogen around the sampleand adjust the liquid level to a f

    37、ixed point on the sample tube.Maintain this level through the test.9.4 Zero the pressure gage, if needed.9.5 Admit the helium gas into the system to a pressure of600 to 900 torr by carefully opening the H valve. Record thispressure, PH1, and the manifold temperature, TH1.9.6 Open the S valve to admi

    38、t helium to the sample.9.7 After about 5 min of equilibration, readjust the liquidnitrogen level (if needed), and record the pressure, PH2andmanifold temperature, TH2.9.8 Repeat 9.5-9.7 for each sample cell attached to themanifold.9.9 Open all S valves, then slowly open the V valve toremove the heli

    39、um gas.9.10 Close the S valve when a pressure below 103torr hasbeen attained. This should normally take 5 to 10 min.10. ProcedureKrypton Adsorption10.1 Close the V valve.10.2 Admit krypton gas by opening the K valve and recordpressure as P1(1) and temperature as T1(1). (It is desirable tochoose P1(1

    40、) such that P2(1)/Po(1) is about 0.05.)10.3 Open the S valve to admit krypton to the sample.10.4 Allow sufficient time for equilibration, readjusting theliquid nitrogen level periodically if needed. Equilibrium shallbe considered as attained when the pressure changes by nomore than 0.001 torr in 5 m

    41、in.10.5 Record the equilibrium pressure, P2(1), and manifoldtemperature, T2(1).10.6 Record the liquid nitrogen temperature T8s(1) or thenitrogen vapor pressure Po,N(1).10.7 Close the S valve.10.8 Repeat 10.2-10.7 until there are at least three points inthe linear BET region (P2/Po,krypton= 0.05 to 0

    42、.30). Designatethe pressures, manifold temperatures, liquid nitrogen bathtemperatures or nitrogen vapor pressures as P1(i), P2(i), T1(i),T2(i), T8s(i), and Po,N(i) respectively for each i8th iteration (i=2ton, where n is the total number of points).NOTE 3The quantity of krypton gas admitted at each

    43、adsorption pointin step 10.2 depends on the manifold volume, possible dosing system,dead space, and sample surface area. It is recommended that small kryptondoses be used initially to ensure that at least three equilibration points areobtained in the linear BET region.10.9 Open the S valve, slowly o

    44、pen the V valve, remove theDewar flask, and allow the sample tube to warm to roomtemperature.10.10 When frost has disappeared from the sample tube,wipe it dry.10.11 Backfill the sample tube with helium to atmosphericpressure or slightly above. Close the S valve.10.12 Detach the sample tube from the

    45、apparatus, recapwith the stopper used previously, and weigh. Record the weightas W2. If the sample was previously weighed followingdegassing, this step may be omitted.11. Calculation11.1 Calculate the weight of sample Wsas follows:Ws5 W2 W1(1)11.2 Calculate the dead space Vsas follows:Vs5T8sVdPH23FP

    46、H1TH11 273.22PH2TH21 273.2G(2)11.3 For each point, i = 1, 2 ., n, calculate the following:11.3.1 If Po,N(i) is not measured directly, the values of T8s(i)can be converted to Po,N(i) by the following equation for 76#T8s(i) # 80:In Po,Ni!/2549.78! 5 Ax 1 Bx 3/2 1 Cx31 Dx6#/1x! (3)where:X = (1Ts/126.2)

    47、,A = 6.09676,B = 1.1367,C = 1.04072, andD = 1.93306 (1).411.3.2 Saturation vapor pressure of krypton Po,krypton(i):Po,kryptoni! 5 exp 1.919 In Po,Ni! 2 11.82 (4)NOTE 4The above calculation of Po,krypton(i) is based on the use of the4The boldface numbers in parentheses refer to a list of references a

    48、t the end ofthis standard.D4780 123Clausius-Clapeyron equation to extrapolate the vapor pressure of liquidkrypton to liquid nitrogen temperature (2, 3). Other methods have beenreported in the literature or are used on commercially available instru-mentation. These methods are acceptable, but should

    49、be identified in thereport.11.3.3 X i! 5 relative pressure 5 P2i!/Po,kryptoni!11.3.4 Manifold temperature in:T81i! 5 T1i! 1 273.2 (5)T82i! 5 T2i! 1 273.211.3.5 The krypton volume in the manifold (and dosingsystem) before equilibration (cm3STP):V1i! 5 Vd3P1i!T1i!3273.2760(6)11.3.6 The krypton volume in the manifold (and dosingsystem) after equilibration (cm3STP):V2i! 5 Vd3P2i!T2i!3273.2760(7)See 6.1.2 for Vd.11.3.7 Total inventory of krypton in the system (cm3STP):Vti! 5 Vti 1! 1 V1i! V2i1! (8)Vt0! 5 011.3.8 Volume of krypton


    注意事项

    本文(ASTM D4780-2012 Standard Test Method for Determination of Low Surface Area of Catalysts and Catalyst Carriers by Multipoint Krypton Adsorption《用多点氪吸附法测定催化剂及催化剂载体的低表面面积的标准试验方法》.pdf)为本站会员(visitstep340)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开