欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D3634-1999(2005)e1 Standard Test Method for Trace Chloride Ion in Engine Coolants《测定发动机冷却剂中痕量氯离子的试验方法》.pdf

    • 资源ID:515141       资源大小:71.45KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D3634-1999(2005)e1 Standard Test Method for Trace Chloride Ion in Engine Coolants《测定发动机冷却剂中痕量氯离子的试验方法》.pdf

    1、Designation: D 3634 99 (Reapproved 2005)e1Standard Test Method forTrace Chloride Ion in Engine Coolants1This standard is issued under the fixed designation D 3634; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last re

    2、vision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.e1NOTEIn 10.3, the solution was corrected editorially t

    3、o AgNo3in June 2006.1. Scope1.1 This test method covers the determination of chlorideion in engine coolants in the range from 5 to 200 ppm in thepresence of up to 0.6 weight % mercaptobenzothiazole.1.2 Other materials that react with silver ion will interfere.1.3 Chloride in engine coolants containi

    4、ng an aryltriazoleinstead of mercaptobenzothiazole can be determined directlyby this test method without pretreatment with hydrogen per-oxide.1.4 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.5 This standard does not purport

    5、 to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. Specific hazardsstatements are given in Section

    6、7.2. Referenced Documents2.1 ASTM Standards:2D 1176 Practice for Sampling and Preparing Aqueous So-lutions of Engine Coolants or Antirusts for Testing Pur-posesD 1193 Specification for Reagent WaterE 200 Practice for Preparation, Standardization, and Stor-age of Standard and Reagent Solutions for Ch

    7、emicalAnalysis2.2 Manufacturing Chemists Association Document:3MCA Chemical Safety Data Sheet SD-533. Summary of Test Method3.1 The sample is first treated at a pH of 12 to 13 withaqueous hydrogen peroxide to oxidize the mercaptobenzothia-zole to soluble, noninterfering sulfonate. The treated sample

    8、 isdissolved in glacial acetic acid and titrated potentiometricallywith dilute standard silver nitrate solution. Since the solubilityof silver chloride in this system is sufficient to preventobtaining a suitable inflection at the very low limit of the testmethod, some chloride is deliberately added

    9、to the glacialacetic acid solvent and then corrected for by a blank titration.4. Significance and Use4.1 This test method permits the determination of very lowlevels of chloride ion in engine coolants containing thecommon corrosion inhibitor, mercaptobenzothiazole, or relatedmercaptans, which would

    10、normally interfere with the titrationby also forming insoluble silver salts with silver nitrate.5. Apparatus5.1 Manual Titrations:5.1.1 pH MeterAn expanded scale pH meter which can beread to 1 or 2 mV is desirable but not required. A silver billetindicator electrode4and glass reference electrode5are

    11、 used forthe chloride titration. The silver electrode should be polishedoccasionally with fine steel wool or scouring powder andthoroughly rinsed.5.1.2 Buret, 10-mL, micro, Class A, calibrated in 0.02-mLdivisions.1This test method is under the jurisidiction of ASTM Committee D15 on EngineCoolants an

    12、d is the direct responsibility of Subcommittee D15.04 on ChemicalProperties.Current edition approved Oct. 1, 2005. Published November 2005. Originallyapproved in 1977. Last previous edition approved in 1999 as D 3634 99e1.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontac

    13、t ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from the Manufacturing Chemists Association, 1825 ConnecticutAve., Washington, DC 20009.4The sole source of supply of the Silver

    14、 Billet Electrode known to the committeeat this time is Fisher Scientific (, Catalog No. 13-620-122). If youare aware of alternative suppliers, please provide this information to ASTMInternational Headquarters. Your comments will receive careful consideration at ameeting of the responsible technical

    15、 committee,1which you may attend.5The sole source of supply of the reference electrode known to the committee atthis time is Fisher Scientific (, Catalog No. 13-620-216). If youare aware of alternative suppliers, please provide this information to ASTMInternational Headquarters. Your comments will r

    16、eceive careful consideration at ameeting of the responsible technical committee,1which you may attend.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.1.3 Beakers, electrolytic, 250-mL tall form.5.2 Automatic Titrators are satisfact

    17、ory for this test method,provided they exhibit resolution and accuracy equivalent tothat specified for manual titrations.5.3 Pipets, 10, 20, and 100-mL, Class A.5.4 Flask, Erlenmeyer, 250 mL, with a 24/40 standard taper,female ground glass joint.5.5 CondenserThe condenser shall be of the water-coole

    18、d, reflux, glass-tube type, having a condenser jacketapproximately 200 mm in length. The bottom end of thecondenser shall have a 24/40 male ground glass joint to matchthe Erlenmeyer flask.5.6 Flask, volumetric, 200 mL, Class A.NOTE 1All glassware should be thoroughly cleaned and reserved foruse in t

    19、his test method. Great care must be exercised to avoid contami-nation. Glassware should be cleaned with chromic acid (WarningSee7.1.) cleaning solution, then thoroughly rinsed with water, then withacetone (WarningSee 7.2.), and dried.6. Reagents and Materials6.1 Purity of ReagentsReagent grade chemi

    20、cals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the American Chemical Society,where such specifications are available.6Other grades may beused, provided it is first ascertained

    21、 that the reagent is ofsufficiently high purity to permit its use without lessening theaccuracy of the determination.6.2 Purity of WaterReferences to water shall be under-stood to mean Type IV reagent water conforming to Specifi-cation D 1193: total particulate and dissolved matter, 2.0 mg/Lmaximum;

    22、 pH at 25C, 5.0 to 8.0; electrical conductivity at25C, 5.0 mho/cm maximum; minimum color retention timeof potassium permanganate, 10 min.6.3 Acetic Acid, Glacial (WarningSee 7.3.).6.4 Hydrogen Peroxide Solution(WarningSee 7.4.)Use 30 mass % hydrogen peroxide (H2O2), reagent grade.Aged or contaminate

    23、d H2O2can undergo considerable decom-position and cause incomplete oxidation of the sulfur com-pounds with subsequent high apparent chloride values; there-fore, fresh reagent should be used.6.5 Potassium Chloride SolutionDissolve 0.20 6 0.02 gof potassium chloride (KCl) in 100 mL of water. The solut

    24、ionwill contain 1 mg of chloride per mL solution.6.6 Silver Nitrate Solution(WarningSee 7.5.) Prepare astandard 0.01 N silver nitrate (AgNO3) solution weekly bydiluting 10 mL of standard 0.1 N aqueous AgNO3solution to100 mL with water. The 0.1 N standardAgNO3solution shouldbe prepared and standardiz

    25、ed in accordance with Sections 44 to48 of Practice E 200.6.7 Sodium Hydroxide Solution(WarningSee 7.6.) Pre-pare a 20 mass % sodium hydroxide (NaOH) solution in water.7. Hazards7.1 Chromic AcidHighly toxic; cancer suspect agent;corrosive; avoid skin contact.7.2 AcetoneExtremely flammable; harmful if

    26、 swallowedor inhaled; causes irritation.7.3 Acetic Acid, GlacialPoison, causes severe burns;combustible; harmful if swallowed or inhaled.7.4 Hydrogen Peroxide SolutionStrong oxidizer; contactwith other material may cause fire; causes severe burns. Do nottightly stopper containers. For further detail

    27、s, see MCAChemi-cal Safety Data Sheet SD-53.7.5 Silver NitrateMay be fatal if swallowed; causes se-vere burns.7.6 Sodium Hydroxide SolutionCauses severe burns toskin and eyes.8. Sampling8.1 Sampling of engine coolant should be carried out inaccordance with Practice D 1176.9. Preparation of Titration

    28、 Solvent9.1 Determine a titration blank on a full 2.3-kg bottle ofglacial acetic acid by titrating 100 mL potentiometrically with0.01 N AgNO3solution. If the blank is more than 0.2 mL of0.01 N AgNO3solution, reject the bottle. If the blank is lessthan 0.05 mL of titrant, add an amount of the KCl sol

    29、ution (1mL maximum) to the glacial acetic acid remaining in the bottle(about 2300 mL) to give an approximately 0.1-mL titration for100 mL of the acetic acid. Determine the blank on exactly 100mL of this titration solvent in duplicate. The values should notdiffer by more than 0.02 mL. Reserve the sup

    30、ply of solvent forthis test method and recheck the blank occasionally.6Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For suggestions on the testing of reagents notlisted by the American Chemical Society, see Analar Standards for LaboratoryChem

    31、icals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmaceutical Convention, Inc. (USPC), Rockville,MD. FIG. 1 Titration Curves for Trace Chloride in Engine AntifreezesD 3634 99 (2005)e1210. Procedure10.1 To a 250-mL Erlenmeyer flask add 50 6 0.1gof

    32、engine coolant and approximately 30 mL of water. Make thesolution strongly alkaline by the addition of 5 mLof 20 mass %aqueous NaOH solution. Add 5 mL of 30 mass % aqueousH2O2with stirring, then connect the flask to a reflux condenserand reflux for 30 min. Cool the solution to room temperatureand tr

    33、ansfer the contents quantitatively to a 200-mL volumetricflask and dilute to volume with water.10.2 In a 200-mL volumetric flask, prepare a blank byadding 5 mL of 30 mass % aqueous H2O2and the same amountof 20 mass % aqueous NaOH solution used in 10.1 and diluteto 200 mL with water.10.3 Pipet 100 mL

    34、 of the glacial acetic acid titration solventinto each of two beakers.Accurately pipet 20 mL of the treatedengine coolant sample into one beaker and 20 mL of the blank(10.2) into the second beaker and allow to dissolve. Titrate thecontents of each beaker potentiometrically with 0.01 N AgNO3solution

    35、while stirring slowly with a magnetic stirrer. Theequilibration of electrode potentials is slow in the vicinity ofthe end point; therefore, the titrant should be added in 0.02-mLincrements in this region and sufficient time allowed for stablereadings to be obtained.11. Calculation11.1 Chloride Conte

    36、nt:11.1.1 Prepare a titration curve by plotting potential read-ings, using 2 mV per division, against the correspondingvolume of titrant added, using 0.02 mL per division. The endpoint is selected at the middle of the steepest portion of thecurve (see Fig. 1).11.1.2 Calculate ppm of the chloride ion

    37、 in the originalengine coolant sample as follows:Chloride, ppm 5V 2 B! N! 35.5! 200! 106!20! 50! 1000!5 V 2 B!N!7100!where:V = titrant used, mL, in the engine coolant sample,B = titrant used, mL, in the blank sample, andN = normality of titrant.12. Report12.1 Report the chloride content of the engin

    38、e coolant tothe nearest unit.13. Precision and Bias13.1 The reproducibility of the chloride ion determinationby this test method is 5 ppm in the range from 5 to 200 ppm.13.2 The bias for this test method has not been determined.14. Keywords14.1 engine coolants; trace chlorideASTM International takes

    39、 no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own resp

    40、onsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addresse

    41、d to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the

    42、address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 3634 99 (2005)e13


    注意事项

    本文(ASTM D3634-1999(2005)e1 Standard Test Method for Trace Chloride Ion in Engine Coolants《测定发动机冷却剂中痕量氯离子的试验方法》.pdf)为本站会员(roleaisle130)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开