欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM C702-1998(2003) Standard Practice for Reducing Samples of Aggregate to Testing Size《将集料的现场试样减小到适于试验的标准实施规程》.pdf

    • 资源ID:508061       资源大小:92.97KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM C702-1998(2003) Standard Practice for Reducing Samples of Aggregate to Testing Size《将集料的现场试样减小到适于试验的标准实施规程》.pdf

    1、Designation: C 702 98 (Reapproved 2003)American Association StateHighway and TransportationOfficials Standard: T 248Standard Practice forReducing Samples of Aggregate to Testing Size1This standard is issued under the fixed designation C 702; the number immediately following the designation indicates

    2、 the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers three methods for the red

    3、uction oflarge samples of aggregate to the appropriate size for testingemploying techniques that are intended to minimize variationsin measured characteristics between the test samples so se-lected and the large sample.1.2 The values stated in SI units are to be regarded as thestandard.1.3 This stan

    4、dard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 A

    5、STM Standards:C 125 Terminology Relating to Concrete and ConcreteAggregates2C 128 Test Method for Density, Relative Density (SpecificGravity), and Absorption of Fine Aggregate2D 75 Practice for Sampling Aggregates33. Terminology3.1 DefinitionsThe terms used in this practice are definedin Terminology

    6、 C 125.4. Significance and Use4.1 Specifications for aggregates require sampling portionsof the material for testing. Other factors being equal, largersamples will tend to be more representative of the total supply.This practice provides procedures for reducing the largesample obtained in the field

    7、or produced in the laboratory to aconvenient size for conducting a number of tests to describe thematerial and measure its quality in a manner that the smallertest sample portion is most likely to be a representation of thelarger sample, and thus of the total supply. Failure to carefullyfollow the p

    8、rocedures in this practice could result in providinga nonrepresentative sample to be used in subsequent testing.The individual test methods provide for minimum amount ofmaterial to be tested.4.2 Under certain circumstances, reduction in size of thelarge sample prior to testing is not recommended. Su

    9、bstantialdifferences between the selected test samples sometimes can-not be avoided, as for example, in the case of an aggregatehaving relatively few large size particles in the sample. Thelaws of chance dictate that these few particles may beunequally distributed among the reduced size test samples

    10、.Similarly, if the test sample is being examined for certaincontaminants occurring as a few discrete fragments in onlysmall percentages, caution should be used in interpretingresults from the reduced size test sample. Chance inclusion orexclusion of only one or two particles in the selected testsamp

    11、le may importantly influence interpretation of the charac-teristics of the original sample. In these cases, the entireoriginal sample should be tested.5. Selection of Method5.1 Fine AggregateReduce the size of samples of fineaggregate that are drier than the saturated-surface-dry condi-tion (Note 1)

    12、 using a mechanical splitter according to MethodA. Reduce the size of samples having free moisture on theparticle surfaces by quartering according to Method B, or bytreating as a miniature stockpile as described in Method C.5.1.1 If the use of Method B or Method C is desired, and thesample does not

    13、have free moisture on the particle surfaces,moisten the sample to obtain free moisture on the particlesurfaces, mix thoroughly, and then reduce the sample size.5.1.2 If use of Method A is desired and the sample has freemoisture on the particle surfaces, dry the entire sample to atleast the saturated

    14、-surface-dry condition, using temperaturesthat do not exceed those specified for any of the testscontemplated, and then reduce the sample size. Alternatively, ifthe moist sample is very large, make a preliminary split usinga mechanical splitter having chute openings of 38 mm (112 in.)or more in widt

    15、h to reduce the sample to not less than 5000 g.Dry the portion so obtained, and reduce it to test sample sizeusing Method A.NOTE 1The method of determining the saturated-surface-dry condi-tion is described in Test Method C 128. As a quick approximation, if the1This practice is under the jurisdiction

    16、 of ASTM Committee C09 on Concreteand Concrete Aggregates and is the direct responsibility of Subcommittee C09.20 onNormal Weight Aggregates.Current edition approved May 10, 1998. Published December 1998. Originallyapproved in 1971. Last previous edition approved in 1993 as C 702 93.2Annual Book of

    17、ASTM Standards, Vol 04.02.3Annual Book of ASTM Standards, Vol 04.03.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.fine aggregate will retain its shape when molded in the hand, it may beconsidered to be wetter than saturated-surface

    18、-dry.5.2 Coarse Aggregates and Mixtures of Coarse and FineAggregatesReduce the sample using a mechanical splitter inaccordance with Method A (preferred method) or by quarteringin accordance with Method B. The miniature stockpile MethodC is not permitted for coarse aggregates or mixtures of coarseand

    19、 fine aggregates.6. Sampling6.1 Obtain samples of aggregate in the field in accordancewith Practice D 75, or as required by individual test methods.When tests for sieve analysis only are contemplated, the size ofthe field sample listed in Practice D 75 is usually adequate.When additional tests are t

    20、o be conducted, the user shall besatisfied that the initial size of the field sample is adequate toaccomplish all intended tests. Use similar procedures foraggregate produced in the laboratory.METHOD AMECHANICAL SPLITTER7. Apparatus7.1 Sample SplitterSample splitters shall have an evennumber of equa

    21、l width chutes, but not less than a total of eightfor coarse aggregate, or twelve for fine aggregate, whichdischarge alternately to each side of the splitter. For coarseaggregate and mixed aggregate, the minimum width of theindividual chutes shall be approximately 50 % larger than thelargest particl

    22、es in the sample to be split (Note 2). For dry fineaggregate in which the entire sample will pass the 9.5-mm(38-in.) seive, a splitter having chutes 12.5 to 20 mm (12 to34in.) wide shall be used. The splitter shall be equipped with tworeceptacles to hold the two halves of the sample followingsplitti

    23、ng. It shall also be equipped with a hopper or straight-edged pan which has a width equal to or slightly less than theover-all width of the assembly of chutes, by which the samplemay be fed at a controlled rate to the chutes. The splitter andaccessory equipment shall be so designed that the sample w

    24、illflow smoothly without restriction or loss of material (see Fig.1 and Fig. 2).NOTE 2Mechanical splitters are commonly available in sizes ad-equate for coarse aggregate having the largest particle not over 37.5 mm(112 in.).8. Procedure8.1 Place the original sample in the hopper or pan anduniformly

    25、distribute it from edge to edge, so that when it isintroduced into the chutes, approximately equal amounts willflow through each chute. Introduce the sample at a rate so as toallow it to flow freely through the chutes and into thereceptacles below. Reintroduce the portion of the sample in oneof the

    26、receptacles into the splitter as many times as necessaryto reduce the sample to the size specified for the intended test.Reserve the portion of material collected in the other receptaclefor reduction in size for other tests, when required.METHOD BQUARTERING9. Apparatus9.1 Apparatus shall consist of

    27、a straight-edged scoop,shovel, or trowel; a broom or brush; and a canvas blanketapproximately 2 by 2.5 m (6 by 8 ft).10. Procedure10.1 Use either the procedure described in 10.1.1 or 10.1.2or a combination of both.10.1.1 Place the original sample on a hard, clean, levelsurface where there will be ne

    28、ither loss of material nor theaccidental addition of foreign material. Mix the materialthoroughly by turning the entire sample over three times. Withthe last turning, shovel the entire sample into a conical pile bydepositing each shovelful on top of the preceding one. Care-fully flatten the conical

    29、pile to a uniform thickness anddiameter by pressing down the apex with a shovel so that eachFIG. 1 Large Sample Splitter for Coarse AggregateC 702 98 (2003)2quarter sector of the resulting pile will contain the materialoriginally in it. The diameter should be approximately four toeight times the thi

    30、ckness. Divide the flattened mass into fourequal quarters with a shovel or trowel and remove twodiagonally opposite quarters, including all fine material, andbrush the cleared spaces clean. Successively mix and quarterthe remaining material until the sample is reduced to thedesired size (Fig. 3).10.

    31、1.2 As an alternative to the procedure described in10.1.1, when the floor surface is uneven, place the field sampleon a canvas blanket and mix with a shovel as described in10.1.1, or by alternately lifting each corner of the canvas andpulling it over the sample toward the diagonally oppositecorner c

    32、ausing the material to be rolled. Flatten the pile asdescribed in 10.1.1. Divide the sample as described in 10.1.1,or if the surface beneath the blanket is uneven, insert a stick orpipe beneath the blanket and under the center of the pile, thenlift both ends of the stick, dividing the sample into tw

    33、o equalparts. Remove the stick leaving a fold of the blanket betweenthe divided portions. Insert the stick under the center of the pileat right angles to the first division and again lift both ends ofthe stick, dividing the sample into four equal parts. Removetwo diagonally opposite quarters, being

    34、careful to clean thefines from the blanket. Successively mix and quarter theremaining material until the sample is reduced to the desiredsize (Fig. 4).NOTE Small Sample Splitters for Fine Aggregate. May be constructed as either closed or open type. Closed type is preferred.FIG. 2 Sample Splitters (R

    35、iffles)FIG. 3 Quartering on a Hard, Clean Level SurfaceC 702 98 (2003)3METHOD CMINIATURE STOCKPILE SAMPLING(DAMP FINE AGGREGATE ONLY)11. Apparatus11.1 Apparatus shall consist of a straight-edged scoop,shovel, or trowel for mixing the aggregate, and either a smallsampling thief, small scoop, or spoon

    36、 for sampling.12. Procedure12.1 Place the original sample of damp fine aggregate on ahard clean, level surface where there will be neither loss ofmaterial nor the accidental addition of foreign material. Mixthe material thoroughly by turning the entire sample over threetimes. With the last turning,

    37、shovel the entire sample into aconical pile by depositing each shovelful on top of thepreceding one. If desired, flatten the conical pile to a uniformthickness and diameter by pressing down the apex with ashovel so that each quarter sector of the resulting pile willcontain the material originally in

    38、 it. Obtain a sample for eachtest by selecting at least five increments of material at randomlocations from the miniature stockpile, using any of thesampling devices described in 11.1.13. Keywords13.1 aggregate; aggregatecoarse; aggregatefine; fieldtestingaggregate; samplingaggregates; sample reduct

    39、ion;specimen preparationASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringe

    40、ment of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard o

    41、r for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views k

    42、nown to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).FIG. 4 Quartering on a Canvas BlanketC 702 98 (2003)4


    注意事项

    本文(ASTM C702-1998(2003) Standard Practice for Reducing Samples of Aggregate to Testing Size《将集料的现场试样减小到适于试验的标准实施规程》.pdf)为本站会员(appealoxygen216)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开