欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM B223-2003 Standard Test Method for Modulus of Elasticity of Thermostat Metals (Cantilever Beam Method)《恒温金属弹性模量的标准试验方法(悬臂梁法)》.pdf

    • 资源ID:460662       资源大小:98.62KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM B223-2003 Standard Test Method for Modulus of Elasticity of Thermostat Metals (Cantilever Beam Method)《恒温金属弹性模量的标准试验方法(悬臂梁法)》.pdf

    1、Designation: B 223 03Standard Test Method forModulus of Elasticity of Thermostat Metals (CantileverBeam Method)1This standard is issued under the fixed designation B 223; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

    2、last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the modu-lus of elasticity of thermostat metals at any temperaturebetwee

    3、n 300 and + 1000F (185 and 540C) by mountingthe specimen as a cantilever beam and measuring the deflectionwhen subjected to a mechanical load.1.2 The values stated in inch-pound units are to be regardedas the standard.1.3 This standard does not purport to address all of thesafety concerns, if any, a

    4、ssociated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet for this product/material as pro-vided by the manufacturer, to establish appropriate safety andhealth practices, and

    5、 determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:B 388 Specification for Thermostat Metal Sheet and Strip23. Terminology3.1 Definitions:3.1.1 thermostat metala composite material, usually inthe form of sheet or strip, comprising two or more

    6、 materials ofany appropriate nature, metallic or otherwise, which, by virtueof the differing expansivities of the components, tends to alterits curvature when its temperature is changed.3.1.2 modulus of elasticitythe ratio, within the elasticlimit of a material, of stress to corresponding strain. In

    7、 this testmethod the modulus of elasticity is calculated from theexpression for the deflection of a cantilever beam undermechanical load which is transposed to read as follows:E 5 4Pl3/dbt3where:E = modulus of elasticity, psi or MPa,P = load, lbf or N,l = gage length, in. or mm,d = specimen deflecti

    8、on, in. or mm,b = specimen width, in. or mm, andt = specimen thickness, in. or mm.4. Apparatus (Figs. 1-3)4.1 Specimen Holder for securely clamping the test speci-men in a horizontal position as a cantilever beam whenimmersed in a bath at the desired temperature. It shall carry amicrometer depth gag

    9、e for reading the deflection of thespecimen and a loading rod for loading the specimen. Both ofthese shall extend sufficiently above the liquid level of the bathto permit the operator to perform the test at the higher testtemperatures.4.1.1 Specimen holder to be made sufficiently rigid to allownorma

    10、l handling without distortion.4.2 Loading Rod,18 in. (3.2 mm) or less in diameter, forcarrying the load and transmitting its weight vertically to thefree end of the cantilever specimen. It shall be made of materialthe same as that of the tube which supports the specimenmounting clamps in order to pr

    11、event a difference in expansionrates from affecting the deflection readings. The bottom endshall be conically shaped and shall rest in the conical punchmark at the free end of the specimen. Any supports shall permitfree movement with specimen deflection and shall provideelectrical insulation from th

    12、e micrometer depth gage. Near thetop shall be a holder for supporting the load. The weight of theloading rod and holder shall be no greater than 1 oz (28 g).4.3 Micrometer Depth Gage, for measuring the deflection ofthe specimen to the nearest 0.0001 in. (0.002 mm). It shall bemounted directly over t

    13、he loading rod. The micrometer shaftshall be in the same vertical line as the loading rod, so thatreadings can be taken of the top of the loading rod for no-loadand full-load positions. The gage shall be insulated electricallyfrom the specimen holder and the loading rod.1This test method is under th

    14、e jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.10 on Thermostat Metals and Electrical Resistance Heating Materials.Current edition approved June 10, 2003. Published August 2003. Originallyapproved in 1948. Last previous edition

    15、 approved in 1997 as B 223 - 97.2Annual Book of ASTM Standards, Vol. 02.04.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.4 Load, constructed so that when placed in the holder, itscenter of gravity will coincide with the center of

    16、 the loadingrod. It shall be readily detachable for the operators conve-nience in taking no-load and full-load readings and shall not beof sufficient weight to deflect the specimen more than 0.30 in.(7.6 mm).4.5 BathA stirred liquid so that the temperature shall besubstantially constant during the t

    17、est.4.6 Electronic Indicator, sensitive, low-current, to give asignal when the micrometer depth gage shaft completes theelectrical circuit across the indicator terminals by touching thetop of the loading rod. The indicator sensitivity shall be suchthat loading rod positions can be determined with a

    18、precision of60.0001 in. (0.002 mm).4.7 All metallic components of apparatus, excluding mi-crometer and loads, should be made of very low coefficient ofthermal expansion materials. The recommended material isinvar.5. Precautions5.1 Load and no-load readings of the various trials will notapproximately

    19、 duplicate each other in the event the load issufficiently great to overstress the specimen beyond its elasticlimit. In this case a new specimen shall be substituted and alighter load used which will not overstress the material.5.2 Modulus of elasticity measurements to be within themaximum recommend

    20、ed temperatures as stated in Specifica-tion B 388.6. Test Specimen6.1 The test specimen shall be the form of a strip approxi-mately 114 in. (31.8 mm) longer than the gage length. Thethickness may be any value between 0.015 and 0.055 in. (0.38FIG. 1 Testing Machine for Determining Modulus of Elastici

    21、ty of Thermostat MetalFIG. 2 Specimen Mounting Clamp AssemblyB223032and 1.40 mm); however, corresponding width values shallconform with those in Fig. 4. Width and thickness dimensionsshall be determined with a precision of 60.0001 in. (0.002mm).7. Preparation of Specimen7.1 Gage LengthThe gage lengt

    22、h shall be the distance onthe specimen between the center of the punch mark thatsupports the loading rod and the edge of the specimen holderclamps. This punch mark shall be approximately one half of thethickness of the specimen deep and located on the center line14 in. (6.4 mm) from the free end on

    23、low expansion sidesurface. To obtain the necessary accuracy in gage length, thespecimen shall be made as shown in Fig. 5 which, when thespecimen is placed in the specimen mounting clamps, willmaintain the gage length with a tolerance of 60.003 in. (0.08mm). Table 1 gives the gage lengths for various

    24、 specimenthicknesses.FIG. 3 Specimen Mounting Clamp DetailsFIG. 4 Width of Test SpecimenB223033NOTE 1For thicknesses, widths, and lengths not covered by this testmethod, the procedure shall be agreed between the manufacturer and thepurchaser.7.2 After being roughly cut, slit, or sheared from the sam

    25、ple,the test specimen shall be finished to size by careful machiningor filing.7.3 Preforming OperationThe specimen shall be pre-formed into a shape approximating the segment of a circle. Theamount of this preforming shall be such that, when subjected tothe desired temperature, the specimen will take

    26、 an upwardcurvature sufficient to cause the no-load and full-load deflec-tion positions to be approximately equally distant above andbelow the straight position (Fig. 6).7.4 Heat TreatmentAfter the preforming work has beencompleted the specimen shall be heat treated to relieve allinternal stresses.

    27、This treatment shall consist of heating thespecimen while free to bend at a prescribed temperature and fora prescribed time. Heat treatment shall be at least 50 F higherthan the maximum tested temperature at a soak time of 1 h. Thedetails of this procedure will depend on the characteristics ofthe th

    28、ermostat metal and shall be mutually agreed upon by themanufacturer and the purchaser.7.5 MarkingAny identification marking shall be placedon that part of the fixed end of the specimen not included in thegage length.8. Procedure8.1 CleaningCarefully remove any oxide coating andother foreign substanc

    29、es from all those surfaces which directlyaffect the electrical resistance of the electronic indicator circuitthrough the testing apparatus. This operation is necessary topermit maximum sensitivity of the indicator. The top of theloading rod which touches the micrometer depth gage shaftmay be ground

    30、to a point in order to further increase theindicator sensitivity.8.2 Test RoutineClamp the specimen securely in thespecimen holder using the 0.125-in. (3.18-mm) dowel hole and0.125-in. dowel pin for accurate positioning. Lower the bottompart of the specimen holder with the specimen into the bath oft

    31、he desired temperature and support the apparatus rigidly. Placethe lower end of the loading rod in the punch mark at the freeend of the specimen. Connect the electronic indicator toterminals on the specimen holder. When satisfactory initialconditions have been established, adjust the micrometer dept

    32、hgage until the electronic indicator signals that the gage shaft istouching the loading rod and record this position as the no-loadreading. Deflect the specimen by placing the load on the loadholder and record this position of the rod as the load reading.The difference between these two readings wil

    33、l be the amountof deflection. Obtain an average value of deflection from ten ormore trials.8.3 Calculation of Modulus of ElasticitySubstituting thespecimen size and the average deflection for a known load inthe equation in 3.1.1, calculate the modulus of elasticity, E,asin the following example:E 5

    34、4Pl3/dbt3where:P = 4.00 ozf = 0.250 lbf or 1.112 N,l = 4.00 in. or 101.6 mm,d = 0.1863 in. or 4.732 mm,b = 0.5000 in. or 12.700 mm, andFIG. 5 SpecimenTABLE 1 Gage Length of Test SpecimenSpecimen Thickness Gage Lengthin. mm in. mm0.015 to 0.0199, incl 0.38 to 0.509, incl 212 612 63.5 6 1.30.020 to 0.

    35、0249, incl 0.51 to 0.639, incl 3 612 76.2 6 1.30.025 to 0.0299, incl 0.64 to 0.759, incl 312 612 88.9 6 1.30.030 to 0.0349, incl 0.76 to 0.889, incl 4 612 101.6 6 1.30.035 to 0.0449, incl 0.89 to 1.139, incl 412 612 114.3 6 1.30.045 to 0.055, incl 1.14 to 1.40, incl 5 612 127.0 6 1.3FIG. 6 Relations

    36、hip of Specimen No-Load, Straight, and Full-LoadPositions at Test TemperatureB223034t = 0.0301 in. or 0.765 mm.Substituting the known values,E =(43 0.250 lbf 3 (4.00 in.)3)/0.1863 in. 3 0.500 in. 3 (0.0301 in.)3)E = 25 194 029 psi.orE =(43 1.112 N 3 (101.6 mm)3)/(4.732 mm 3 12.700 mm 3 (0.765mm)3)E

    37、= 173 386 MPa.9. Report9.1 The report shall include the following:9.1.1 Type of thermostat metal,9.1.2 Dimensions of specimen in inches or millimetres,9.1.3 Temperature of test,9.1.4 Direction of grain on specimen, and9.1.5 Modulus of elasticity in pounds-force per square inchor megapascals.10. Prec

    38、ision and Bias10.1 PrecisionThe precision of this test method wasperformed in accordance with the test procedure and loadknown to 60.04 % results in a 2-sigma measurement precisionof 61.8 %.10.2 BiasComparison to accepted reference values indi-cates lack of bias.11. Keywords11.1 cantilever; loading

    39、rod; modulus of elasticity; thermo-stat metalASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, an

    40、d the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revisi

    41、on of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you sh

    42、ouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).B223035


    注意事项

    本文(ASTM B223-2003 Standard Test Method for Modulus of Elasticity of Thermostat Metals (Cantilever Beam Method)《恒温金属弹性模量的标准试验方法(悬臂梁法)》.pdf)为本站会员(twoload295)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开