1、+!/-o 3 MIL-T-63264 (2) 47 777770b 0252677 1 MIL-T-63264 (AR) AMENDMENT 2 S UP E RSE D I NG AMENDMENT 1 .UN- 11 October 1979 MILITARY SPECIFICATION TEST, SET, ELECTRONICS SYSTEMS: M92 This amendment forms a part of Military Specification MIL-T-63264 (AR), dated 3 May 1978, and is approved for use by
2、 the US Army Armament, Munitions and Chemical Command and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 Under “Military Standards“ : Delete the following: “MIL-STD-331 -Fuze and Fuze Components, Environmental and Performance Tests For“. * Add : “MIL-STD-20
3、2 -Test Methods For Electronic and Electrical Component Parts“. PAGE 3 3.4, Delete: “except for temperature humidity which is contained in MIL-STD-331“. 3.4.1, Add to end of paragraph: “using curve AW of Figure 514.2-7“. 3.4.2: Delete “Test 105.1 of MIL-STD-331 .I and substitute “Method 507.1, Proce
4、dure I“. * 3.5: Delete “MIL-STD-1460, except that para. 4.1.3 does not apply“ and add “MIL-S-45743 and MIL-S-46844“. AMSC N/A I of 3 FSC 4925 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without
5、 license from IHS-,-,-* * * MIL-T-63 2 64 (AR) AMENDMENT 2 PAGE 5 TABLE I, line 2, Transportation Vibration: Add i(a)ts in Add to Notes: I (a) Order of tested as listed“. examination or test column. PAGE 7 4.4.2.1: Delete Minor Defect 201. PAGE 10 4.4.2.4, under Examination or Test column: Specify M
6、ajor Defects 102 and 103 and Minor Defect 201 are to be performed prior to assembly . - - - PAGE 14 4.4.2.8 Change the title from: “Electronic Flash Assembly“ to “Printed Wiring Board Assembly“. Change Drawing Number rom: “926713“ to “12624794“. Add Major 103: “Any part missing, damaged or improperl
7、y assembled to the x-y orientation, . . . O. 40%, 3.2, VisuaL“. PAGE 35 Add: “Figure 10 to Schematic. PAGE 41 4.5.lC Test #5, Step 2: 4.5.2: Delete in its entirety. Delete “16-20“ and substitute “16-30“. PAGE 43 4.5.3, Add after “Procedure XI: 4.5.4: Delete in its entirety and substitute: “using cur
8、ve AW of Figure 514.2-7“ “4.5.4 Temperature humidity. Using equipment in accordance with 4.4.4, subject each first article unit to Test Method 507.1, Procedure I of MIL-STD-810. Replace Step 6 and 7 of test method with the following: 2 Provided by IHSNot for ResaleNo reproduction or networking permi
9、tted without license from IHS-,-,-MIL-T-63264 (AR) AMENDMENT 2 Step 6 - At the end of the tenth cycle, remove and inspect the test item and condition the test item at 25 + 50 (ambient) for at least one (1) hour, operate the test- item and obtain results in accordance with General Requirements, 3.2.
10、F : Any item which fails to meet the applicable requirements shall cause the first article sample to be rejected.“ The inargins of this amendment are marked with an asterisk or vertical line to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were
11、 made. This was done as a convenience only and - the Government assumes no. liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations-and relationship to the last previous amendment. : Custodian: Army-AR Preparing activity : Army-AR (Project : 49 2 5-AO48) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
