1、 flIL-G-LlLb5 13 W 7777706 03168b5 L I . 5-37-6 4 MIL-G-48165 (MU) 31 July 1973 . SUPERSEDING (See 6.6) MILITARY SPECIFICATION GRENADE, Gap.: M43A1 AND BOMB, BLU-18 CONTAINER ASSEMBLY FOR 1. SCOPE 1.1 This specification covers the c ntainer assembly for Grenade, G.P.: M43A1,and Bomb, BLU-18* 2. APPL
2、ICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS MILITARY MIL-A-2550 - Ammunition, General Specification For STANDARDS MILITARY MIL-STD-105 - Sa
3、mpling Procedures and Tables for Inspection by Attributes (ABC-STD-105) and Definitions MIL-STD-109 - Quality Assurance Terms t#iS bO however,a few light scratches not exposing base material may be permitted. All required marking and stamping shall be neat and sharply defined. njurious to any part,
4、nor shall theparts be contaminated Exterior surface coatings shall be con- 3 . 4 Submission of results of contractor-Qonucted e-xamna- tions and tests.-The contractor shall forward copies of the results of any of his examinations or tests to the designated address as required by the contract. (See 6
5、.5) 3.5 First article testing.-This specification makes pro- visions for first article testing. quantity by the contractor shall be as specified in the contract. Submission of first article 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility .fop inspectn.-Unless otherwise speci- Except as otherwise
6、specified in the contract fied in the contractor or purchase order, th.e supplier is respon-. sible for the performance of all inspection requirements as specified herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-48165 (MU) or order, the
7、 supplier may use his own or any other facilities suitable for the performance of the inspection requirements specffied herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed n
8、ecessary to assure supplies and services conform to prescribed requirements. Reference shall be made to MIL-STD-109 to define terms used herein. The provisions of MIL-A-2550 shall apply. lot of items deliverable under the contract is submitted to the Government for acceptance, the contractor shall s
9、upply the following information accompanied by a certificate which attests that the information provided is correct and applicable to the product being submitted: assurance provisions specified in this specification. with identification and date of changes thereto. meets requirements when such mater
10、ial is purchased by the contractor or commercial specifications referenced in any of the contractual documents, and that certificates of conformance are on file and available for review. 4.1.1 Submission of product.-At the time the completed a. A statement that the lot complies with all the quality
11、b. Drawing and specification number and date, together C. A statement that all material purchased by the contractor d. Number of items in the lot. e. Date submitted. f. Number of units of product inspected. g, Results obtained, ,by code number, for all inspections performed. The certificates shall b
12、e signed by a responsible agent of the certifying organization. The initial certificate submitted shall be substantiated by evidence of the agents authority to bind his principal. Substantiation of the agents authority will not be required with subsequent certificates unless, during the course of th
13、e contract, this authority is vested in another agent of the certifying organization. 4.2 First article inspection. 4.2.1 Submission.-The contractor shall submit a first article quantity as designated by the Contracting Officer for evaluation in accordance with the provisions of 4.2.2. (See 6.1.) Th
14、e first article sample shall consist of the following: a, Twenty-five (25) of each part. b. Twenty-five (25) container assemblies. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-48165 (MU) All parts and completed assemblies submitted shall hav
15、e been produced by the Contractor (or furnished by a supplier) using the same production processes, procedures and equipment as will be used in fulfilling the contract. All parts and material including packaging and packing, shall be obtained from the same sources of supply as will be used in regula
16、r production. sample shall be accompanied by certificates of conformance. A first article quantity, or portion thereof, as directed hy the Contracting Officer, shall also be submitted whenever there is a lapse in production for a period in excess of 90 days, or whenever a change occurs in manufactur
17、ing process (including heat treatmenk procedures and equipment, material used, drawing specification or source of supply as to significantly affect product uniformity as determined by the Government. Prior to submission, the contractor shall inspect the sample to the degree necessary to assure that
18、it conforms to the requirements of the contract and submit a record of this inspection with the sample. will not be submitted unless specifically authorized by the Contracting Officer. The A sample containing known defects 4.2.2 Inspection to be performed.-All parts and assemblies shall be subjected
19、 by the Government to any or all the examinations or tests specified in this specification and any or all require- ments of the applicable drawing. 4.2.3 Rejection.-If any part or assembly fails to comply The- Government reserves the right with any of the applicable requirements, the first article q
20、uantity shall be rejected. to terminate its inspection upon any failure of any part or assembly. In the event of rejection, the Government reserves the right to require the contractor to take corrective action and submit a new first article quantity or portion thereof. until a first article quantity
21、 is accepted, the contractor is in no way authorized by the Government .to resume regular production unless otherwise directed by the Contracting Officer. 4.3 Inspection p.r.ovisons .- 4.3.1 Lot formatLon.-The term “inspection lott1 as used in this specification is defined as an essentially homogene
22、ous callection of units of product from which a representative sample is drawn and inspected to determine conformance with. applicable requirements. only that quantity of units from which th.e sample was drawn and shall not be construed to represent any prior or subsequent quantities pagsented for i
23、nspection. Homogeneity shall be con- sidered to exis-t-provided the inspection lot has been produced by one manufacturer, in one unchanged process in accordance with the same drawing, same drawing revision, same specification and The- sample selected shall represent 5 k i i Provided by IHSNot for Re
24、saleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-48165 (MU) - 105. Diameter of hole Gage 01005 106. Concentricity of diameter of hole with outside diameter Gage O1006 Minor
25、 : 201. Evidence of poor workmanship (See 3.3) Visual 01007 4.3.2.2 Container (See Dwg. C-8875902 or B-8881923, as applicable, covering a detal of DWg. C-8875901 and .C-8881922 r.e.sp ) Cat egories Defects Method of Critical: None defined Maj or Inspection 101. Crack, perforation or distortion Visua
26、l Major: (See 4.3.3.1) 102. Inside diameter Gage 103. Height Gage 104. Thickness at bottom Gage 105. Thickness of sidewall, min. Gage Code No. 02001 02002 02004 02003 02005 Minor 201. Radius missing Visual 02006 202. Evidence of poor workmanship (See 3.3) Visual 02007 4.3.2.3 Container Assembly, pri
27、or to assembly of disc and cover (See DWg. C-8875901 or C-8881922, a% app-cable-) Cat egories Defects Method of Code Critical: None defined Inspection No. Major O 3 O 0.1 101. Neight of propellant Balance Minor Visual 0300.2 201. Foreign matter (See 3-3) Provided by IHSNot for ResaleNo reproduction
28、or networking permitted without license from IHS-,-,-MIL-.G- 4 81 6 5 (MU) Categories Defects Method of. Code Inspection No . Critical: None defined Major: None defined Minor 201. Disc missing or damaged Visual 04001 202. Evidence of poor workmanship (See 3.3) Visual 04002 4.3.2.5 Container Assembly
29、 (See Dwg, C-8875901 or C-8881922, as applicable) . Categories Defects Method of Code Inspection No . Critical: None defined Maj or 101. Height A8870054 05001 102 Outside diameter, max. Gage 05002 103. Crimp less than 360O Visual 05003 Minor: 201. Evidence of poor workmanship 202. Cover, disc or con
30、tainer (See 3.3) Visual 05004 damaged, (dented, punctured etc.) Visual 05005 4.3.2.6 Inner Set-up Box (prior to sealing (See Dwg. F-9206733). Categories Defects Method of Code Inspection No . Critical: None defined Maj or 101. Incorrect number of container assemblies Visual 06001 102. Packing cushio
31、n missing Visual 06002 Minor: None defined 8 I I . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - - .s MIL-G-48165 (MU) 463.2.7 Inner Set-up Box (Sealed) (See Dwg. F-9206733). Cat egories De fe cts Method of Code Critical: None defined Ma j or In
32、spection No. 101. Box damaged to the extent that contents are exposed Visual 07001 Minor 201. Contents loose 202. Marking misleading or unidentifiable Manual 07002 Visual 07003 4.3.2.8 Outer Set-up box (prior to sealing) (See Dwg. F-9206733)- Co de Categories Defects Method of Critical: None defined
33、 Major Inspect ion No. 101. Incorrect number of inner Set-up boxes Visual 08001 Minor: 201 . 4.3.2.9 Filler mat erial insufficient or missing Visual 08002 Barrier Bag (prior to sealing) (See Dwg. F-9206733). Defeets Method of Code Cate gories Critical: None defined Major Inspection No. 101. Corners
34、not blunted Visual 09001 102 Sealing strap incomplete, badly wrinkled or missing Visual 09.002 Minor 201. Marking mkleading or uniidentifiable Visual 09003 , . . 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-48165 (MU) 4.3.2.10 Box, Piber(p
35、rior to sealing) (See Dwg. C-9206734). Categories Defects Critical: None defined Method of I nsp e c t ion Major 101. Heat seals missing, unsealed or improperly positioned on barrier bags Vis ual Minor 201. Marking misleading or unidentifiable Visual 4.3.2.11 Box, Fiber (sealed) (See Dwg. C-9206734)
36、. C at e go ri es Critical: None defined Defects Major 101. Box damaged exposing contents 102. Sealing strip incomplete, badly wrinkled or missing Minor 201. Contents loose 202. Marking misleading or unidentifiable Method of Inspect ion Visual Visual Manual Visual Co de No . 10001 10002 Code No. 110
37、01 11002 11003 11004 4.3.3 Testing. 4.3.3.3 Dimensional control of stamped parts .-In place of the normal sampling associated with the Classification of Defects, and with the approval of the Contracting Officer, a sample of at least ten (10) parts may be dimensionally inspected to qualify the tool u
38、sed in the stamping process for use in production. In addition, a random sample of five (5) parts shall be selected from the last portion of each hours production for dimensional inspection as a control of the tool during production. If any defective parts are found during qualification of the tool,
39、 the tool producing the defective-part shall If any defective parts are found when inspection is performed for control of the tool, the tool producing the =* not be used in production. 10 f I i 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL- G
40、- 4 81 6 5 (NU) defective part shall be removed from production. that portion of production since the last tool control check shall be returned to the contractor for corrective action. Further, All tools removed from praduction because of some fault, may, after reworking, be returned to production p
41、roviding they pass the qualification test above. The Contractor may request a change of inspection frequency providing he presents objective evidence to the Contracting Officer- to substantiate the request. 4.3.3.2 Moisture and total volatiles content of pro- pellant (See Dwg. C-?8875?9i o?r C-88819
42、22); Maj.0.r DeTe?ct (Code No?. 12001.-The contractor shal provide adequate controls to insure compliance with the applicable requirements. The moisture and total volatiles content of the propellant shall be determined at the loading station at the time of loading This determination shall be made at
43、 least once each eight (8) hours of production. Sampling of the propellant shall be in accordance with MIL-STD-286, Method 101.2.2. In addition, if the moisture and total volatiles content fails to comply wit- the requirement specified on the applicable drawing, and load- ing has not begun, the prop
44、ellant lot shall be rejected until corrective action has been taken as verified by repeating the moisture and total volatiles content determination. If load- ing has begun, container assemblies loaded with the non-con- forming propellant shall be rejected. shall be performed as specified in 4.4.1. T
45、his determination 4.3.4 Inspection equipment.-The inspection equipment required to perform the examinations and tests prescribed in this section is identified under the ?Method of Inspectiont1 headings in 4.3.2 and in 4.3.3 (See 6,3). 4.4 Test methods and procedures 4.4.1 Mossture and total volatile
46、s Content of pro.pellant The moisture and total volatiles content of the propellant shall be determined at the time and place of loading and in accordance with MIL-S?ID-286, Method 101.2.2. propellant c.nnt.enf _ ,oading and in accordance 5 . PREPARATION FOR DELIVERY 5 . 1 Preservat?i?on and pckging
47、 5.i,l -Level C.-The container assembly shall be preserved and packaged in accordance with Dwg. F-9206733. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL- G- 4 8165 (MU ) 5.2 Pac Ring . 5.2.1 Level C.-The container assemblies, preserved and pack
48、aged as specified in 5.1.1, shall be packed for shipment in accordance with Dwg. C-9206734. 5.3 Marking.-Marking shall be in accordance with Dwgs. F-92mnd C-9206734 and Code of Federal Regulations, Title 49, Parts 171-179. 5.4 Shipping.-When assemblies from more than one lot are shipped as a carload
49、, each lot shall be kept separate, and the division between lots clearly indicated to prevent mixing of the lots in transit. 6. NOTES 6.1 Ordering data.-Procurement documents shall specify a. Title, number and date of this specification. b. Data cards shall be prepared for each lot in accordance with the information specified in
