1、i4 Februarv 1978 . SUPERSEBING MILITARY SPECIFICATION CANISTERS, SNOIE, HC 155W4 PROJECTILE, Ml and 142; COMPONENTS FOR This specification is approved for use by US Army Armament Research and Development Command, Department of the Army and is available for use by all Departments and Agencies of the
2、Depart- ment of Defense. 1. SCOPE 1.1 This speciffcation covers the components for two types of canisters. 1.2 Classification. “he canister components shall be furnished in the following iqpes as specifYed ( see 6-21: Type Ml - Canister, Smoke, HC, lS5MM Shell, Components Far Type M2 - .Canister, Sm
3、oke, HC, 155MM Shell, Com:onents For (TDPL15-11-121) (TDPL15-11-122) 2. APPLICABLE DQCUMENTS 2.1 Government documents. The following dacuments of khe issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein: FSC 1320 : B
4、eneficial comments (recommendations,additions, deletions) and any : : pertinent data which may be of use in improving this document should : : be addressed to: Commander, ;IS Army Armament Research and Development: : Comand;Attn: DRDAR-TSC-C, Aberdeen Proving Ground, MD 21010 by us-: : ing the self-
5、addressed Standardization Document Improvement Proposal : : (DD Form 1426) appearing at the end of this docu:ent or by Letter. THIS DOCUMENT CONTAINSILPAGES A .- - . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDS MILITARY MIL-STD-105 - Sam
6、pling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage. MTL-STD- - Ammunition Data Card. MIL-STD-1168 - Lot Numbering of Ammunition. DRAWINGS US ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND CHEMICAL SYSTEMS LABORATORY TDPL15-11-121 - Canister, Smoke
7、, HC, 155MM Shell, M1; Components TDPL15-11-122 - Canister, Smoke, HC, l55MM Shell, M2, Components For. For. (Copies of specifications, standards, drawings, and publications re- quired by contractors in connection with specific procurement functions should be obtained from the procuring activity or
8、as directed by the contracting officer ) . 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.1.1 Materials . All materials cited on TDPLlj-ll-l21(Ml) and TDPL15- 11-122 (M2mthe subsidiary drawings shall conform to the specifi- cations listed thereo
9、n or to the characteristics set forth on the drawings. 3.1.2 Components. A11 components of the canisters shall conform to the specifications and drawings listed on TDPL15-11-121 and TDPL15-11-122 and subsidiary drawings. 3.2 Assembl , The body and tube shall be in accordance with Drawings Ci-li-C1-1
10、1M), D15-1l-hO(Ml), and Di5-11-48 (M2) and shall be assembled in accordance with the body assembly Drawings D15-11-38(1) and C15-11-46(M2) . Surface treatment shall be in accordance with appli- cable drawings and specifications. 3.3 Welds, The body assembly shall not contain more than three ceDa- ra
11、ted projections when tested as specified in 4.4.4;i. 3.4 Salt spray. The body assemblies and closing disks shall meet the requirements of 141-P-16232 when tested as specified in 4.4.4.2. 3.5 Preproduction. production lot shall be produced in accordance.with this specification for examination and tes
12、t (see 4.3). Prior to the start of regular production, a pre- 3.6 Workmanship. The components shall be free from rust, contamination (foreign matter, oil, or grease),. and damage such as dents, cracks, or de- formation which could affect their intended uce. 4. QUALITY ASSURANCE PROVISIONS 4.1 Respon
13、sibility for inspection. 4.1.1 Contractors responsibility. Unless otherwise specified in the . contract or purchase order, the contractor is responsible for the perform- ance of all.inspection requirements as specified herein. Except as other- wise specified in the contract, the contractor may use h
14、is own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. reserves the right to perform any of the inspections.set forth in the spec- ifications where such inspections are deemed necessary to assure supplies and
15、 services conform to specified requirements. The Government 4.1.2 Additional contractors responsibility. Drawings for contractor designed inspection equipment (other than standard measuring equipment ) shall be forwarded to the design agency for approval prior to use for 3 CI-_.- Provided by IHSNot
16、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-51358A 13 m 7977706 0333877 5 m. . MIL-C-51358A(EA) production (see 6.2) . ister metal components manufacturer shall be responsible for the minimum mechanical property tests required by drawing Ci?-11-39 and Ci5-11-
17、47. Tests shall be performed by a Government approved laboratory. Minimum mechanical property tests shall be found satisfactory prior to production, Provisions of MIL-A-2250 apply, Amnunition data cards prepared in ac- cordance with MIL-STD-i167 shall be forwarded with each lot of components, For pr
18、eproduction and regular production, the can- 4.1.3 Government responcibilxty. Unless .otherwise specified, the Goverment will be responsible for.preproduction inspection. duction samples (4.3.2) shall be forwarded to the design agency laboratory designated by the contracting officer (see 6.2) . Prep
19、ro- or 4.1.4 Objective evidence. The contractor shall provide ob3 ective evi- dence acceptable to the contracting officer that the requirements of 3.1 and section 5 of which specific inspection has not been provided in Specifically laboratory test data and tool control dimensional data shall be prov
20、ided to the contrac- ting officer as proof of compliance of the materza1 specified for the components, . 4.2 Ciassification of inspections. .this specification have been satisfied. (a) Preproduction inspection (see 4.3). (b) Quality conformance inspection ( see 4.4 . 4.3 Preproduction inspection. 4.
21、3.1 Lot, A preproduction lot of 500 sets of components of the type specified7ee 6.2) shall be manufactured using the same methods, materials, equipment, processes, and cycle time as will be used during regular pro- duction. Components consist of body, tube, body assembly, closure disk, zinc sleeve a
22、nd packing disk. warded to the design agency or Government designated laboratory for in- spection and evaluation prior to proceeding with regular production (see 6.2). . Samples as required by 4.3.2 shall be for- Provisions of MIL-A-2550 shall apply. 4.3.2 Sampling. 4.3.2.1 For examination, Componen
23、ts sufficient to assemble 50 canis- Five samples each of the specified body, formed tube ters of the type specified (see 6.2) shall be taken at random from the preproduction lot. . and tube flat development, shall be selected and checked against their respective drawings. ir -_ -_ -_ Provided by IHS
24、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-WIL-C-51358A 13 m 9799906 0333878 7 m - 4.3.2.2 For destructive tests. (a) Body assembly and closing disk. Ten body assemblies of each type specified (see 6.2) and closing disks shall be taken at random from the prepr
25、oduction lot. (b) Body. Five bodies of each type specified (see 6.2) .shall be taken at random from the preproduction lot for testing (see 4.1.2). . (c) Body assembly and closing disk after varnish. Five body assemblies of each type specified (see 6.2) with varnish applied per Dwg Di5-11-38 and 1215
26、-11-46 and closing disks, shall be taken .at random-from the preproduction lot. . 4.3.3 Inspection procedure. 4.3.3.1 For examination. The sample components shall be examined in accordance with tfie clasSification of defects (4.4.3,3) and MIL-STD-105. The individual bodies, and tub-es in flat and fo
27、rmed configurations shall be examined for conformance to their respective dratrings. number is zero. The acceptance 4.3.3.2 For destructive tests. Five-body assemblies of each type in accordance with 4,4.4.i. No body assembly shall contain more than three separated projections. (b) Body. Five bodies
28、 shall be tested in accordance with the applicable drawings. The acceptance number is zero. (c) Body assembly and closing disk, Five body assemblies of each type specified (see 6.2) and closing disk shall be tested in accord- ance with 4.4.4.2. Assemblies shall meet the requirements of MIL-P-s for t
29、ype Z, class 3 for 2 hours. (d) Body assembly an closing disk after varnish. Five body assemblies of each type specified (see 6.2) with varnish applied per Dwg Di5-11-38 and Di5-11-46 and closing disk, shall be tested in accordance with 4.4.4 . 2. for type Z, class 2 for 48 hours. The varnished area
30、s shall meet the requirements of MIL-P-16232 , 4.3.h Acceptance/rejection criteria. The preproduction samples shall comply with 4.3.3 to be acceptable. The supplier shall obtain written approval from the contracting officer prior to proceeding with regular production. 5 Provided by IHSNot for Resale
31、No reproduction or networking permitted without license from IHS-,-,-MIL-C-51358A 13 m 9999906 0333873 9 m. MIL-C-51358A( EA) . 4.4 Quality conforniance inspection. 4.4.1 Lotting. Each lot shall be identified and controlled in ac- cordance with MIL-STD-1168. A lot shall consist of like components of
32、 one type or like subassemblies of one type, one interfix number, produced by one manufacturer, from the same materials and unde: essentially the same manufacturing conditions. No one lot of.any component shall contain steel from more than one heat of steel. Provisions of ML-A-2550 shall apply 4 . 4
33、 . 2 Sampling. 4.4.2.1 For examination. Sampling shall be conducted in accordance with MIL-Sm-105. 4.4.2.2 For destructive tests. (a) Body assembly and closing disk. Ten body assemblies of each type specified (see 6.2) (Drawing Di?-11-38 and Di5-11-46 and closing disks, shall be taken at random from
34、 each lot. (b) Body. Five bodies of each type specified (see 6.2) (Drawing CU-11-39 and C15-11-47) shall be taken at random from pro- duction at increments not to exceed 50,000 bodies and when the manu- facturing process changes or a new heat of steel is used. be as specified in 4.1.2. Testing shall
35、 (c) Body assembly and closing disk after varnish. Five body assemblies of each type specified (see 6.2), with varnish applied per Dwg Di5-11-38 and ci5-11-46 and closing disk; shall be taken at random from each lot. 4.4.3 Inspection procedure. 4.4.3.1 For examination. The sample components shall be
36、 examined in accordance with the classification of defects (4.4.3.3) and MIL-STD-105, 4.4.3.2 For destructive tests. (a) Body assemblies. Five body assemblies of the type speci- fied (see 6.2) shall be tested in accordance with 4.4.4.i. number is zero. The acceptance (b) Body. Five bodies of the typ
37、e specified (see 6.2) shall . be tested in accordance with the applicable drawings. number is zero. The acceptance 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(c) Body assembly and closing disk. Five body assemblies of each type specified (see
38、6.2) and closing disk shall be tested in accordance with 4.4.4.2. MIL-P-16232, for type Z, class 3 for 2 hours. Assemblies shall meet the requirements of (d) Body assembly and closing disk after varnish. Five body assemblies of each type specified (see 6.21, with varnish applied per Dwg Di5-11-38 an
39、d ci5-11-46 and closing disk, shall be tested in accordance with 4.4.4.2. The varnished area of the body assembly shall meet the re- quirements of MIL-P-16232, for. type Z, class 2 for 48 hours. 4.4.3.3 Classification of defects. (See pages 8 thru 12). 4.4.4 - Tests. Tests shall be conducted as foll
40、ows: 4.4 . 4.1 - Welds . (a) Secure assembly in suitable fixture which allows bottom tube weld area free movement. (b) Place a 24 inch rigid hollow bar snugly over perforated Move bar laterally, touching dia- tube (bar shall have a ll8-inch maximum wall thickness-and shall show no evidence of bendin
41、g during test). . metrically opposite walls and return to center. one time only. (c) Remove bar and remove assembly from fixture. (d) Examine projection welds for metal separation, cracks or other failures. 4.4.4.2 Salt s ra test. The body assembly and closing disk of the type specified *hall be sub
42、jected to a salt spray test in accordance witn the requirements of MIL-P-16232. 5. PREPARATION FOR DELIVERY 5.1 Packaging and packing. level B. 5.1.1 Body assembly, metal (see 6.2). Twenty-four empty metal con- tainers of the same type shall be packaged together in two layers of 12 canisters each. i
43、sters per row. Inter-locking fiberboard partitions shall be used to separate the canisters from each other. In addition, full size separator pads shall be placed on the bottom of the canisters, between the two layers and on top of the canisters. The partitions and the separator pads shall be constru
44、cted of material conforming to grade V3c of PPP-F-320. Each layer shall be arranged in four rows.of three can- This Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1111111 Im 1, . 11 119 mmmmmmm m m mm mmm a .i4 k 2 d QI 2 o u il Provided by IHSNot f
45、or ResaleNo reproduction or networking permitted without license from IHS-,-,-c U Fi L U cc Ir (r I c Y ! 5 MIL-C-51358A 13 = 7777706 0333882 7 J- P M A I .II ?Y M M M m-m m m occooc 5-=i=i=i o. o o o c o 0- . e, ta al Pi Provided by IHSNot for ResaleNo reproduction or networking permitted without l
46、icense from IHS-,-,-rlrlc O0 HBU 00% 111 mmm k oc, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-51358A 13 7777706 033388q 2 I c: I E n al aal a, In 8 3 CI) E w B 8 o tl .rl .ri k *ri V H 3 rl d k o .-I O O I rl O k C O o 4 O O H a .ri k .al
47、a al d 8 2 z ci al k o fi ri ffl ffl al o 2 B c, o E ci c G 8 ri s 4 c, o k O .ri E. o Ri al CI) al k k O d 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-51358A -13 W 9999906 0333885 LI W .fi Ut 3i - - . .I .- b OOQ z fi $ a 8 a a Q1 M i a
48、k O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I- flIL-C-5135A L3 - 9999906 0333887 - 6.2 Ordering data. Procurement documents should specify the following: (a) (b) (c) Preproduction. . Title, number and date of this specification. Type of canister (Ml or M2) required. (.1) Time allowed for supplier submission of samples for Government inspection, test, and evaluation after award of contract.
