1、 A-A-58033 = 9999974 03b5374 634 M INCH - POUND A-A- 58031 MIL-V-87991 (84) COMMERCIAL ITEM DESCRIPTION VAN, MULTI-PURPOSE MORTUARY SERVICE: COMMERCIAL This commercial item description is approved for use by the US Air Force, and is available for use by all Departments and Agencies of the Department
2、 of Defense. 1. SCOPE. This Commercial Item Description describes a commercial, gasoline engine powered, multi-purpose funeral service vehicle utilizing a commercial van chassis with full window body. 2. 3. a. CLASSIFICATION. The van shall be one of the following types: Type I - Full size standard v
3、an, two rear wheel driven Type II - Mini-size van, two front or two rear wheel driven SALIENT CHARACTERISTICS: Curb weight. The vehicle fully equipped with a full compartment of fuel, lubricants and coolant shall weigh not less than that specified below. weight shall include all standard equipment a
4、nd accessories required by this document. The Type I - 4300 pounds Type II - 2800 pounds Beneficial comments, recommendations, additions, deletions, clarifications, etc, and any data which may improve this document should be sent to: WR-ALC/LVRG, 225 Ocmulgee Court, Robins AFB GA 31098-1647 AMSC N/A
5、 FSC 2320 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A 58031 b. Design. Item Number 21, Type II, Class C for full size van and Item number 20 or 2O/XL, Type II,
6、Class B for mini-van, except as specified herein. The Gross Vehicle Weight (GVW) shall be the vehicle curb weight plus the total number of passengers shown in the following paragraph 2.p, at 175 pounds each. The vehicle shall meet or exceed the requirements of FED-STD-307, c. Performance. The vehicl
7、e shall be capable of transporting the rated payload at a continuous speed of not less than 55 miles per hour (MPH) on level pavement. start to 55 MPH in not more than 20 seconds on level pavement while transporting the rated payload. The vehicle shall also be capable of accelerating from a standing
8、 d. Engine. The Type I shall have not less than 8 cylinders, and the Type II not less than 6 cylinders. governing Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Engines in effect on the date of manufacture. The vehicle shall comply with EPA regulations e. Engine cooling syste
9、m. A heavy duty cooling system shall be provided. The coolant shall be maintained at a temperature below the boiling point when the vehicle is operated in a fully loaded condition at an altitude of 10,000 feet above sea level, and in an ambient temperature of not less than 125 degrees Fahrenheit (F)
10、 during normal driving conditions and for at least on hour of engine idling with the air conditioning system operating. f. Electromagnetic interference. The entire vehicle shall be suppressed to limit electromagnetic radiation in accordance with SAE J551. used, shall conform to SAE 5552. Suppressers
11、 where g. Transmission. An automatic transmission, with a transmission cooler, shall be provided. h. Electrical system. the electrical system shall be 12 volts. The entire vehicle electrical loads operating simultaneously under all conditions of vehicle operation including prolonged periods of norma
12、l engine idle without discharge from the battery. satisfy this requirement, but in no case shall alternator capacity be less than 50 ampere peak output, or less than 30 ampere output at normal engine idle speed. The alternator shall be of sufficient capacity to 2 Provided by IHSNot for ResaleNo repr
13、oduction or networking permitted without license from IHS-,-,- A-A-58031 = 9999974 0165376 Y07 A-A 58031 i. Steerinq. Power steering shall be provided. j. Service brakes. Power assisted service brakes shall be provided. k. Suspension. Hydraulic, double-acting shock absorbers shall be furnished on th
14、e front and rear axles. 1. Dimensions. The vehicle in fully operational condition, including all equipment and accessories, shall be as followings: a. Length: Type I - at least 206 inches bumper to bumper. Type II - at least 198 inches bumper to bumper. b. Width (except for mirrors and their bracket
15、s): Chassis manufacturers standard for full window van. c. Height: Chassis manufacturers standard for full window van. m. Wheelbase. The Type I shall be not less than 125 inches, nor greater than 140 inches. inches. The Type II shall be not less than 109 inches, nor more than 12 n. Seats. All seats,
16、 except for the rearmost seat, shall be the manufacturers deluxe conversion package high-back adjustable bucket type seats. individual seats shall also have folding armrests and shall swivel 360 degrees. The rear seat shall be the couch type. All seats except the 2 front seats, shall be quickly and
17、easily removed. The Type I shall provide seating for at least 9 passengers. The Type II shall provide seating for at least 7 passengers. The O. Doors. A door shall be provided for the driver, front seat passenger, a sliding side door on the curb side of the passenger/casket compartment, and rear doo
18、r(s) . The rear door(s) shall be either one or two doors that shall permit unhampered loading and unloading of the casket or cots. The door(s) shall be able to be unlocked and opened from both the inside and outside. The rear door openings shall have the minimum following sizes: Type I - Height shal
19、l be the manufacturers standard for a full window van The width shall be the manufactures standard for a full window van, but not less than 52 inches. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A 58031 Type II - Height: 39 inches. Width: 50
20、inches. p. Windows and door locks. provided. Power windows and power door locks shall be q. Wipers and washers. Wipers shall have at least 2 speeds. The manufacturers standard windshield washer shall be provided. r. Wheels and tires. Steel belted radial, tubeless tires with highway treads shall be p
21、rovided. A spare wheel and tire assembly shall be provided, mounted and concealed within the vehicle body. The locatin of the spare tire assembly shall neither interfere with the function of the vehicle nor necessitate moving the casket when removal of the spare tire is required. s. Tools. Tools nec
22、essary to change a tire, including at least a jack, handle, and wheel lug nut wrench shall be provided. t. manufacturers standard commercial practice, unless otherwise required, when rustproofing shall be in accordance with FED-STD-297 for tropical rustproofing (see paragraph 8, “Notes“). Rustproofi
23、nq. The vehicle shall be rustproofed in accordance with the u. Passenger compartment heating and cooling. The manufacturerIs standard, or if available, the optional, heavy-duty heating and air conditioning systems shall be provided, except the air conditioning system shall use no Class 1 ozone deple
24、ting substance (ODS) . v. Casket/passenger compartment. With the passenger seats removed, the casket/passenger compartment shall be of a size and arrangement adequate for the transportation , loading and unloading through the rear door(s) of a casket case having a maximum gross weight, including wei
25、ght of the deceased, of 600 pounds or two side by side mortuary cots with remains with a maximum weight of 300 pounds each. The manufacturers standard or optional tiedowns shall be provided for both mortuary cots. rearmost position to the rear of body at the floor) shall be not less than that listed
26、 below. standard full window van height and the minimum distance between the wheel The compartment length (from rear of drivers seat to The height shall be not less than the chassis manufacturers 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A
27、58031 housings shall be not less than 48 inches. The interior shall be of currently available materials with all accessories and decoration matching or compatible colors. Type I - 113 inches Type II - 104 inches w. flat and unobstructed. The material. Floor. The floor in t,.e casket/passenger compar
28、tment shall be essentially floor covering shall be current production carpet x. Interior lighting. At least two casket/passenger compartment lights that are the shrouded, indirect type, that operate when any door is opened shall be provided. sliding doors. open. Dual flood lamps shall be mounted adj
29、acent to the rear and side These floodlamps shall operate when the rear or sliding door is y. A casket table and rollers for rear loading shall be provided. Locking devices shall be provided for properly positioning and holding the casket case or casket in fully extended position at the rear door fo
30、r loading or off-loading and in retracted position while being transported. shall be constructed of chrome plated or stainless steel and shall be capable of supporting a casket case having a maximum gross weight of 600 pounds including weight of the deceased. Casket rack. The casket rack z. Casket r
31、oller board. The manufacturers standard commercial roller board with chrome adjustable restraints for casket loading and off-loading shall be provided. casket/passenger compartment floor. easily installed and removed. installation vehicle. The roller board carpet shall match the carpet the carpet on
32、 the The roller board shall be capable of being If tools are required for removal or of the roller board, such tools shall be provided for each aa. Removable window panels. If required (see paragraph 8, “Notes“), the Type II shall be provided with the manufacturers standard commercial removable wind
33、ow panels with landau bars for the rearmost side windows. panel colors shall match the vehicles exterior color, and the panels interior color shall match the vehicles interior color. The exterior Panels shall be capable of 5 Provided by IHSNot for ResaleNo reproduction or networking permitted withou
34、t license from IHS-,-,-A-A-56031 = 9999974 0365379 Llb A-A 58031 being easily installed and removed and shall be resistant to damage from the elements and from usage. bb. Draperies and venetian blinds shall be provided for all side and rear windows of the cacket/passenger compartment. These draperie
35、s and venetian blinds shall be capable of being easily removed and reinstalled, and their color shall be the same as, or complimentary to, the vans interior. Draperies. cc. Radio. The chassis manufacturers standard, or optional, AM/FM stereo cassette sound system shall be provided. dd. Casket table
36、and bier pin set. If required (see paragraph 8, “Notes“), the manufacturers standard or optional commercial casket table and bier pin set shall be provided. ee. Finish. silver gray. The exterior paint color shall be the chassis manufacturers 4. RECOVERED MATERIALS: The successful contractor is encou
37、raged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. rebuilt, or remanufactured components, pieces, and parts shall not be incorporated into the vehicle. However, used, 5. CONTRACTOR CERTIFICATION: The contractor shall certify that the product offe
38、red meets the salient characteristics of this comercial item description and conforms to the producers own drawings, specifications, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and therefore as may be otherwise provi
39、ded for under the provisions of the contract. 6. COMMERCIAL: The vehicle furnished shall be, as of the date of award, the latest model (with minor modifications, as that term is defined in DoD FAR Supplement 252.211-7012, Paragraph K-85 of the solicitation) of an established product previously produ
40、ced and sold in substantial commercial quantities (exceeding the criteria at FAR 15.804-3(f) (2) (ii) (A) for at least one year. The vehicle furnished, or earlier models of it, absent minor modifications, shall have routinely been 6 Provided by IHSNot for ResaleNo reproduction or networking permitte
41、d without license from IHS-,-,-C a A-A 58031 supported with spare/repair parts which were produced or sold in the normal course of business. Administrative Contracting Officer with verification of compliance with these requirements. information on the vehicle (or its earlier models) being offered as
42、 a commercial item: At the time of delivery, the contractor shall furnish the Offers shall provide, as part of their proposals, the following (1) Total sales to the U.S. Government or to contractors for U.S. Government use during the previous one year period. (2) Total sale of the item to the genera
43、l public during the three years. (3) Length of time the item has been sold in the commercial market place. (4) Other pertinent information necessary to determine that the item is an established commercial item. 7. PACKAGING, PACKING, AND MARKING: Unless otherwise specified in the contract, the vehic
44、le shall be prepared for delivery by common carrier and shall provide for protection against loss or damage while in transit. A permanently marked identification plate, shall be securely mounted at the drivers compartment. following information: The plate shall contain the NOMENCLATURE MANUFACTURERS
45、 MODEL NUMBER MANUFACTURERS SERIAL NUMBER MANUFACTURER S NAME MANUFACTURERS ADDRESS MANUFACTURERS SERVICE PHONE NUMBER DATE OF MANUFACTURE CONTRACT NUMBER NATIONAL STOCK NUMBER REGISTRATION NUMBER 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-
46、A-58031 7999974 0165381 874 A-A 58031 8. OZONE DEPLETING SUBSTANCE: No Class 1 ozone depleting substance (ODS) shall be used in the design, manufacture, test, operation, or maintenance of this vehicle. For this document, a Class 1 ODS is any of the following: CFC 11, CFC 12, CFC 13, CFC 111, through
47、 CFC 115, CFC 211 through CFC 217, Halon 1011, Halon 1202, Halon 1211, Halon 1301, Halon 2402, Carbon Tetrachloride, Methyl Chloroform, and Methyl Bromide. 9. NOTES: The purchaser shall specify the following at time of purchase: a. If rustproofing in accordance with FED-STD-297 for tropical rustproofing is required. b. If removable window panels are required. c. If casket table and bier pin set is required. CUSTODIAN: AIR FORCE - 99 PREPARING ACTIVITY: AIR FORCE - 84 PROJECT NUMBER: 2320-0641 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
