欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM F2132 - 01(2008)e1 Standard Specification for Puncture Resistance of Materials Used in Containers for Discarded Medical Needles and Other Sharps (Withdrawn 2017).pdf

    • 资源ID:287184       资源大小:105.13KB        全文页数:5页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM F2132 - 01(2008)e1 Standard Specification for Puncture Resistance of Materials Used in Containers for Discarded Medical Needles and Other Sharps (Withdrawn 2017).pdf

    1、Designation: F2132 01 (Reapproved 2008)1Standard Specification forPuncture Resistance of Materials Used in Containers forDiscarded Medical Needles and Other Sharps1This standard is issued under the fixed designation F2132; the number immediately following the designation indicates the year oforigina

    2、l adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorial changes were made throughout in June 2008.1. Scope1.1 The purpo

    3、se of this specification is to provide a testprocedure and performance requirement for the punctureresistance of materials used in the construction of containersfor discarded medical needles and other sharps. This testspecification will establish (1) the average puncture force and(2) a minimum value

    4、 of puncture force that container materi-al(s) must withstand when following the test procedure de-scribed in Section 6. This specification shall be applicable toregions of uniform material and thickness, and needle contactareas as defined in 3.1.7 and 3.1.9. Materials meeting theperformance require

    5、ments of Section 4 shall be considered“puncture-resistant.” This specification does not evaluate theconstruction of, or provide pass/fail criteria for, a sharpscontainer.1.2 This specification provides a test procedure to determineif all regions of one container meet the material punctureresistance

    6、requirements. It does not define the number ofadditional test containers required to achieve a statisticallyvalid sample of a manufacturing lot or process. An appropriatesampling plan shall be determined by the test requester, as thisdepends upon the manufacturing process variability, manufac-turing

    7、 lot size, and other factors, such as end-user require-ments.1.3 This specification is intended to evaluate the perfor-mance of materials used in the construction or manufacture ofsharps containers under controlled laboratory conditions, andat normal room temperature (see 6.1). (WarningThis speci-fi

    8、cation only characterizes material puncture resistance atnormal room temperatures. Applications of sharps containersoutside the range of 23 6 2C (such as usage in emergencyvehicles) require further material characterization by the prod-uct specifier to determine suitable use.)1.4 The values stated i

    9、n inch/pound are to be regarded as thestandard. The SI values given in parentheses are for informa-tion only.1.5 The following hazard caveat pertains only to the testprocedure portion, Section 6, of this specification.1.6 This standard does not purport to address all of thesafety concerns, if any, a

    10、ssociated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E691 Practice for Conducting an Interlaboratory Study

    11、toDetermine the Precision of a Test Method2.2 ISO Standards:ISO 7864 Sterile Hypodermic Needles for Single Use3ISO 594 Luer Fittings32.3 Other Standards:AS 4031:1992 Non-reusable Containers for the Collection ofSharp Medical Items Used in Health Care Areas4BSI 7320:1990 Specification for Sharps Cont

    12、ainers5CSA Z316.6-95 Evaluation of Single Use Medical SharpsContainers for Biohazardous and Cytotoxic Waste6DHHS (NIOSH) Publication No. 97-111 Selecting,Evaluating, and Using Sharps Disposal Containers71This specification is under the jurisdiction of ASTM Committee F04 onMedical and Surgical Materi

    13、als and Devices and is the direct responsibility ofSubcommittee F04.33 on Medical/Surgical Instruments.Current edition approved Feb. 1, 2008. Published March 2008. Originallyapproved in 2001. Last previous edition approved in 2001 as F2132 01. DOI:10.1520/F2132-01R08E01.2For referenced ASTM standard

    14、s, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, Ne

    15、w York, NY 10036, http:/www.ansi.org.4Available from Standards Australia International Ltd., 286 Sussex St., Sydney,Australia NSW 2000.5Available from British Standards Institute (BSI), 389 Chiswick High Rd.,London W4 4AL, U.K., http:/www.bsi-.6Available from Canadian Standards Association, Andre Wi

    16、saksana, 178Rexdale Blvd., Etobicoke, ON Canada M9W 1R3.7Available from Publications Dissemination, EID National Institute for Occu-pational Safety and Health, 4676 Columbus Pkwy., Cincinnati, OH 45226-1998.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428

    17、-2959. United StatesNOTICE: This standard has either been superseded and replaced by a new version or withdrawn.Contact ASTM International (www.astm.org) for the latest information13. Terminology3.1 Definitions:3.1.1 containera product used for the containment ofdiscarded medical needles and other s

    18、harps.3.1.2 materialthe substance(s) used in the construction ofa sharps container.3.1.3 puncture forcethe minimum force applied to therepresentative sharp object that causes its tip to penetrate (exit)the opposite side of the test specimen from the side that itentered when tested in accordance with

    19、 the test procedureportion, Section 6, of this specification.3.1.4 puncture resistanta region of uniform material andthickness is defined as puncture resistant if it meets Section 4of this specification when tested in accordance with Section 6of this specification.3.1.5 test specimena sample of mate

    20、rial being evaluatedfor puncture resistance that is taken from the actual container(direct method) or a representative example of the material andthickness having the same characteristics as the actual con-tainer (indirect method). Refer to Section 5.3.1.6 puncture test specimena test specimen that

    21、has beenpunctured using the puncture test described in 6.3, and subse-quently evaluated using the direct or indirect methods de-scribed in 7.1 and 7.2 of this specification.3.1.7 region of uniform material and thicknesssharps-contact areas of the container, in aggregate, that are made of thesame hom

    22、ogeneous, composite, or laminated material, and, asa consequence of fabrication or design or both, are expected tohave the same material and thickness as other areas of thecontainer. For example, in molded containers, the cornerscould be expected to be of different thickness than the sides andbottom

    23、, resulting in different regions of uniform material andthickness. Labels, tabs, membranes, or thin films coveringopenings in the container are considered separate regions ofuniform material and thickness.3.1.8 sharpsitems used in medical treatment, diagnoses,or research that may cause puncture woun

    24、ds, cuts, or tears inskin or mucous membranes, including, but not limited to:hypodermic, surgical, suture, and IV needles; Pasteur pipets,lancets, razors, scalpels, and other blades and sharp objects.3.1.9 sharps-contact areasthe material of a container thatrepresents those surfaces that enclose sha

    25、rps within thecontainer, when in its final closure configuration (that is,disposal) configuration.4. Performance Requirements4.1 Puncture Resistance SpecificationWhen tested in ac-cordance with Section 6, the average puncture force to pen-etrate material test specimens representing any regions ofuni

    26、form material and thickness and sharps-contact areas, asdefined in Section 3, shall not be less than 3.4 lbf (15 N), withno one value from any region of material tested less than 2.8lbf (12.5 N).4.2 Layered Materials and LinersIf a container is de-signed to use nonlaminated layers of material in sha

    27、rps-contactareas, the combination of these layered materials must betested as configured in actual use and shall meet the punctureresistance specification of this standard to be deemed puncture-resistant. If a container is designed to use a removable linerenclosed by the container, the material used

    28、 in the removableliner must meet the puncture resistance specification of thisstandard to be deemed puncture-resistant.For example, layered materials must be tested with the samespacing as configured in the actual application.5. Sampling and Specimen Preparation5.1 Direct Versus Indirect MethodEithe

    29、r of two testingprocedures may be used to demonstrate that the material ispuncture-resistant under this specification. The direct methodshall be used if the material being evaluated has unknowncharacteristics. The indirect method may be used only if thematerial being evaluated has been previously ch

    30、aracterized bya puncture force versus thickness relationship (see 7.2.2).5.1.1 Direct Method Specimen Preparation:5.1.1.1 One sharps container shall be selected at random torepresent the material(s) to be tested. If it is not possible toobtain the required number of test specimens from onecontainer,

    31、 additional randomly selected containers shall besampled until the required number of test specimens is ob-tained.5.1.1.2 Identify each region of uniform material and thick-ness (see 3.1.7 and 3.1.9). Mark each region with a grid of 1-in.(25.4-mm) squares until the entire region has been covered. If

    32、it is not possible to fit a 1-in. grid over certain areas of thecontainer, a smaller grid may be used; however, it shall be noless than 0.5 in. (12.7 mm) on a side.5.1.1.3 Number every square of the grid so that each regionof uniform material and thickness has consecutive numbers,starting with No. 1

    33、 in each region.5.1.1.4 Using a random-number generator or table, select aquantity of 1-in. (or 0.5-in.) square specimens equal to 10 % ofthe surface area of each region of the container as defined in3.1.7 or no less than twelve specimens from each region. If atleast twelve specimens cannot be obtai

    34、ned from one container,refer to 5.1.1.1. Remove the specimens identified by therandom number selection from each region of the test con-tainer. Mark the test specimen as it is removed to identify theinside of the container, as the puncture is required from theinside of the container outward.5.1.1.5

    35、Measure, mark, and record the thickness at thecenter of each selected test specimen using a thickness-measuring device capable of measuring in 0.001-in. (0.025-mm) increments, with an accuracy of 2 % of the thicknessmeasured, for example, a ball micrometer with a ball diameterof 0.06 to 0.125 in. (1

    36、.6 to 3.2 mm). If the test specimenincludes a radius, corner, edge, or other design feature, find theminimum thickness and mark the location, if not in the centerof the specimen. Identify the specimen as to material andthickness represented.5.1.1.6 Proceed to Section 6.5.1.2 Indirect Method Specimen

    37、 Preparation:5.1.2.1 Obtain fabricated or molded test specimens (referredto as plaques within the indirect section) representing eachmaterial, range of thickness, and equivalent manufacturingF2132 01 (2008)12process used to represent the sharps container. These plaquesshall not be from the container

    38、 itself, but shall be used tocorrelate the measured thickness of an actual container to thepuncture resistance value of plaques having the same charac-teristics.5.1.2.2 Produce a minimum of nine test plaques to representa minimum of four different thicknesses that span the range ofthicknesses expect

    39、ed for each region of uniform material andthickness of the representative container. Select nine testplaques from a minimum of four thickness ranges for aminimum of 36 specimens. The size of each prepared plaqueshall be determined as in 5.1.1.2.5.1.2.3 Measure and record the thickness at the center

    40、ofeach selected test plaque, using the same thickness measuringdevice as in 5.1.1.5, and identify the plaque as to material andthickness represented.5.1.2.4 Proceed to Section 6.6. Puncture Test Procedure6.1 Conditioning:6.1.1 Condition all test specimens at 23 6 2C for 24 hbefore testing. If the ma

    41、terial is hydrophilic, a 50 6 5%relative humidity shall be used.6.1.2 Conduct tests under the same standard laboratoryconditions as those used for conditioning.6.2 Apparatus Requirements:6.2.1 Testing Machineany force-generating device ca-pable of operating a movable member at a constant rate ofmoti

    42、on. The testing machine shall be calibrated according tothe manufacturers instructions.6.2.2 Crosshead Speed Controla drive mechanism forimparting to the movable member of the testing machine auniform, controlled velocity of 4 in./min (100 mm/min) withrespect to the fixed member.6.2.3 Load Indicator

    43、a load-indicating mechanism shall becapable of measuring and recording force with an accuracy of61 % of the measured test force.6.2.4 Representative Sharp Objectregular wall and bevel,Luer-type hypodermic needle, 21 gage by 1 in. (0.8 by 25.4mm) that meets ISO Standards 7864 and 594.6.2.5 Needle Hol

    44、derany Luer-type fitting or other suitableholder that will attach the needle securely to the testingmachine or load indicator at an angle of 90 6 5 with respectto the test specimen.6.2.6 Specimen Supporta block of any suitably rigidmaterial (aluminum, steel, wood, and so forth) conforming tothe dime

    45、nsions of the block shown in Fig. 1.6.2.7 Puncture Sensing Deviceany device capable of sens-ing when the needle tip just penetrates (exits) the opposite sideof the test specimen from the side which it enters, and, whenused in conjunction with the load indicator, records the forceapplied to the needl

    46、e as its tip just penetrates (exits) thespecimen. Any mechanism or materials used to sense punctureshall not influence the test results.NOTE 1A suitable means of sensing puncture is to place a piece ofthin metal foil secured with suitable adhesive on the side of the testspecimen corresponding to the

    47、 outside of the container. The foil is wiredsuch that an event marker will indicate, on the load indicator, the forcebeing applied to the needle when it just penetrates the sample and touchesthe metal foil. The foil shall be in intimate contact with the test specimen(that is, no air bubbles). Sugges

    48、ted foil is 0.001-in.-thick aluminum foodwrap; a suggested adhesive is household glue stick.6.3 Puncture Test:6.3.1 Prepare the testing machine and specimen support andset the crosshead speed velocity to 4 in./min (100 mm/min).6.3.2 Affix a new needle to the needle holder. Zero the loadindicator to

    49、account for the weight of the holder and the needle.6.3.3 Secure the test specimen on the specimen support sothat the surface of the specimen corresponding to the insidesurface of the container (if applicable) is facing toward, and isperpendicular to, the needle. Any securing mechanism used toaffix the specimen to the support shall not influence the testresults. The test specimen, as identified in 5.1.1.5, shall beplaced over the hole of the specimen support, with the area tobe punctured directly under the needle. Do not alter or di


    注意事项

    本文(ASTM F2132 - 01(2008)e1 Standard Specification for Puncture Resistance of Materials Used in Containers for Discarded Medical Needles and Other Sharps (Withdrawn 2017).pdf)为本站会员(吴艺期)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开