1、03-10 23 36 00 - 1 SECTION 23 36 00 AIR TERMINAL UNITS SPEC WRITER NOTE: 1. Delete between/-/ if not applicable to project. Also delete any other item or paragraph not applicable in the section and renumber the paragraph. 2. References to pressure in this section are gage pressure unless otherwise n
2、oted. PART 1 - GENERAL 1.1 DESCRIPTION SPEC WRITER NOTE: Edit each of the following paragraphs as necessary to agree with products being used. Air terminal units, air flow control valves. 1.2 RELATED WORK A. Section 13 05 41, SEISMIC RESTRAINT REQUIREMENTS FOR NON-STRUCTURAL COMPONENTS: Seismic rest
3、raints for equipment. B. Section 23 05 11, COMMON WORK RESULTS FOR HVAC AND STEAM GENERATION: General mechanical requirements and items, which are common to more than one section of Division 23. C. Section 23 05 41, NOISE AND VIBRATION CONTROL FOR HVAC PIPING AND EQUIPMENT: Noise requirements. D. Se
4、ction 23 31 00, HVAC DUCTS AND CASINGS: Ducts and flexible connectors. E. Section 23 09 23, DIRECT-DIGITAL CONTROL SYSTEM FOR HVAC: Valve operators. F. Section 23 05 93, TESTING, ADJUSTING, AND BALANCING FOR HVAC: Flow rates adjusting and balancing. G. Section 23 82 16, AIR COILS: Heating and Coolin
5、g Coils pressure ratings. 1.3 QUALITY ASSURANCE Refer to Paragraph, QUALITY ASSURANCE, in Section 23 05 11, COMMON WORK RESULTS FOR HVAC AND STEAM GENERATION. 1.4 SUBMITTALS A. Submit in accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, and SAMPLES. B. Manufacturers Literature and Data:
6、 1. Air Terminal Units: Submit test data. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-10 23 36 00 - 2 2. Air flow control valves. SPEC WRITER NOTE: Samples are generally not required as submittals. However, for large installations, samples can
7、 be requested in consultation with the Resident Engineer and Medical Center. Use paragraph C below for compliance. C. Samples: Provide one typical air terminal unit for approval by the Resident Engineer. This unit will be returned to the Contractor after all similar units have been shipped and deeme
8、d acceptable at the job site. D. Certificates: 1. Compliance with paragraph, QUALITY ASSURANCE. 2. Compliance with specified standards. E. Operation and Maintenance Manuals: Submit in accordance with paragraph, INSTRUCTIONS, in Section 01 00 00, GENERAL REQUIREMENTS. 1.5 APPLICABLE PUBLICATIONS A. T
9、he publications listed below form a part of this specification to the extent referenced. The publications are referenced in the text by the basic designation only. B. Air Conditioning and Refrigeration Institute (AHRI)/(ARI): 880-08 . Air Terminals Addendum to ARI 888-98 incorporated into standard p
10、osted 15th December 2002 C. National Fire Protection Association (NFPA): 90A-09 . Standard for the Installation of Air Conditioning and Ventilating Systems D. Underwriters Laboratories, Inc. (UL): 181-08 . Standard for Factory-Made Air Ducts and Air Connectors E. American Society for Testing and Mat
11、erials (ASTM): C 665-06 . Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing 1.6 GUARANTY In accordance with the GENERAL CONDITIONS PART 2 - PRODUCTS DESIGNERS NOTE: See HVAC Design Manual Appendix 7-A Table 7-A1 for high humidit
12、y areas. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-10 23 36 00 - 3 2.1 GENERAL A. Coils: 1. /Surgical Suite AHU: Provide copper fins and copper coils for all hot water reheat coils serving surgical suite/. 2. /All Air-Handling Units: Provide
13、 aluminum fins and copper coils for all hot water reheat coils/. 3. Water Heating Coils: a. ARI certified, continuous plate or spiral fin type, leak tested at 2070 kPa (300 PSI). b. Capacity: As indicated, based on scheduled entering water temperature. c. Headers: Copper or Brass. d. Fins: Aluminum,
14、 maximum 315 fins per meter (8 fins per inch). e. Tubes: Copper, arrange for counter-flow of heating water. f. Water Flow Rate: Minimum 0.032 Liters/second (0.5 GPM). g. Provide vent and drain connection at high and low point, respectively of each coil. h. Coils shall be guaranteed to drain. 4. Elec
15、tric Heating Coils: a. ARI certified, spiral fin type. b. Capacity: As indicated, based on scheduled data. c. Coil: Enclosed copper tube, aluminum finned element of coiled nickel-chrome resistance wire centered in tubes and embedded in refractory material. Exposed helical coil of nickel-chrome resis
16、tance wire with refractory ceramic support bushings will not be allowed. B. Labeling: Control box shall be clearly marked with an identification label that lists such information as nominal CFM, maximum and minimum factory-set airflow limits, coil type and coil connection orientation, where applicab
17、le. C. Factory calibrate air terminal units to air flow rate indicated. All settings including maximum and minimum air flow shall be field adjustable. D. Dampers with internal air volume control: See section 23 31 00 HVAC DUCTS and CASINGS. E. Terminal Sound Attenuators: See Section 23 31 00 (HVAC D
18、UCTS AND CASINGS). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-10 23 36 00 - 4 2.2 AIR TERMINAL UNITS (BOXES) A. General: Factory built, pressure independent units, factory set-field adjustable air flow rate, suitable for single duct applicati
19、ons. Use of dual-duct air terminal units is not permitted. Clearly show on each unit the unit number and factory set air volumes corresponding to the contract drawings. Section 23 05 93, TESTING, ADJUSTING, AND BALANCING FOR HVAC work assumes factory set air volumes. Coordinate flow controller seque
20、nce and damper operation details with the drawings and Section 23 09 23, DIRECT-DIGITAL CONTROL SYSTEM FOR HVAC. All air terminal units shall be brand new products of the same manufacturer. DESIGNERS NOTE: All boxes for the new construction and major renovation shall be DDC controlled. Use non-DDC b
21、oxes for minor replacement projects, where the existing air-handling units are not DDC controlled. B. Capacity and Performance: The Maximum Capacity of a single terminal unit shall not exceed 566 Liters/second (1,200 CFM) with the exception of operating rooms and Cystoscopy rooms, which shall be ser
22、ved by a single air terminal unit at a maximum of 1,250 Liters/second (3,000 CFM). C. Sound Power Levels: SPEC WRITER NOTE: Coordinate selection of the air terminal units with the acoustic analysis to be performed by the designer. For each terminal unit size, use maximum allowable radiated and trans
23、mitted sound power levels, in all octave bands, based on the maximum inlet static pressure and air volume for each size. Acoustic performance of the air terminal units shall be based on the design noise levels for the spaces stipulated in Section 23 05 41 (Noise and Vibration Control for HVAC Piping
24、 and Equipment). Equipment schedule () shall show the sound power levels in all octave bands. Terminal sound attenuators shall be provided, as required, to meet the intent of the design. D. Casing: Unit casing shall be constructed of galvanized steel no lighter than 0.85 mm (22 Gauge). Air terminal
25、units serving the operating rooms and Cystoscopy rooms shall be fabricated without lining. Provide hanger brackets for attachment of supports. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-10 23 36 00 - 5 1. Lining material: Suitable to provide
26、required acoustic performance, thermal insulation and prevent sweating. Meet the requirements of NFPA 90A and comply with UL 181 for erosion as well as ASTMC 665 antimicrobial requirements. Insulation shall consist of 13 mm (1/2 IN) thick non-porous foil faced rigid fiberglass insulation of 4-lb/cu.
27、ft, secured by full length galvanized steel z-strips which enclose and seal all edges. Tape and adhesives shall not be used. Materials shall be non-friable and with surfaces, including all edges, fully encapsulated and faced with perforated metal or coated so that the air stream will not detach mate
28、rial. No lining material is permitted in the boxes serving operating rooms and Cystoscopy rooms. 2. Access panels (or doors): Provide panels large enough for inspection, adjustment and maintenance without disconnecting ducts, and for cleaning heating coils attached to unit, even if there are no movi
29、ng parts. Panels shall be insulated to same standards as the rest of the casing and shall be secured and gasketed airtight. It shall require no tool other than a screwdriver to remove. 3. Total leakage from casing: Not to exceed 2 percent of the nominal capacity of the unit when subjected to a stati
30、c pressure of 750 Pa (3 inch WG), with all outlets sealed shut and inlets fully open. 4. Octopus connector: Factory installed, lined air distribution terminal. Provide where flexible duct connections are shown on the drawings connected directly to terminals. Provide butterfly-balancing damper, with
31、locking means in connectors with more than one outlet. Octopus connectors and flexible connectors are not permitted in the Surgical Suite. E. Construct dampers and other internal devices of corrosion resisting materials which do not require lubrication or other periodic maintenance. 1. Damper Leakag
32、e: Not greater than 2 percent of maximum rated capacity, when closed against inlet static pressure of 1 kPa (4 inch WG). F. Provide multi-point velocity pressure sensors with external pressure taps. 1. Provide direct reading air flow rate table pasted to box. G. Provide static pressure tubes. Provid
33、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-10 23 36 00 - 6 H. Externally powered DDC variable air volume controller and damper actuator to be furnished under Section 23 09 23, DIRECT-DIGITAL CONTROL SYSTEM FOR HVAC for factory mounting on air termi
34、nal units. The DDC controller shall be electrically actuated. DESIGNERS NOTE: Use of fan-powered terminal units is not permitted for the Nursing Wing and Special Treatment Spaces involving patient care and monitoring. I. Fan powered terminal units: 1. General: The fan will be in a series configurati
35、on inside the unit casing. 2. Fan assembly: Forward curved centrifugal direct drive blower with adjustable speed controller. a. Motor: Integral thermal overload protection. SPEC WRITER NOTE: Schedule motor voltage. 1) 115 V single phase. 208/240 V single phase. 277 V single phase. b. Motor assembly:
36、 Completely isolated from cabinet with rubber vibration mounts. 3. Wiring: Factory mounted and wire controls. Mount electrical components NEMA-1 control box with removable cover. Incorporate single point electrical connection to power source. Provide terminal strip in control box for field wiring of
37、 power source. Provide factory wired non-fused disconnect switch on each terminal unit. 4. Provide 1-inch thick throwaway filter in the return air inlet. 2.3 AIR FLOW CONTROL VALVE (AFCV) SPEC WRITER NOTE: Air valves are typically used on fume hood type systems. When higher velocities are encountere
38、d these devices can be noisy. It is recommended that the engineer or designer consult the manufacturer when using air valves to ensure that all aspects of the application are covered including controls, acoustics and corrosion. Consult various manufacturers to ensure the intent and quality of operat
39、ion is met by all. A. Airflow control device shall be a venturi valve type air flow control valve. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-10 23 36 00 - 7 DESIGNERS NOTE: For critical applications (e.g. fume hoods, biological hoods, and is
40、olation rooms) requiring pressure control shall use a venturi valve. Rooms that require differential airflow control can use a VAV box if approved by the facility. B. Pressure independent over a 150 Pa-750 Pa (0.6 inch WG 3.0 inch WG) drop across valve. C. Volume control accurate to plus or minus 5%
41、 of airflow over an airflow turndown range of 16 to 1. No minimum entrance or exit duct diameters shall be required to ensure accuracy or pressure independence. D. Response time to change in command signal and duct static pressure within three seconds. SPEC WRITER NOTE: Provide aluminum construction
42、 for non-fume hood and non-corrosive applications such as isolation room exhaust tracking. E. 16 gauge spun aluminum valve body and control device with continuous welded seam and 316 stainless steel shaft and shaft support brackets. Pressure independent springs shall be stainless steel. Shaft bearin
43、g surfaces shall be Teflon or polyester. SPEC WRITER NOTE: Provide stainless steel valve body and valve with phenolic coating for standard fume hood applications. F. 316 stainless steel continuous welded seam valve body, control device, shaft, shaft support bracket, pivot arm and internal mounting l
44、ink. The control device shall have a baked on corrosion resistant phenolic coating. The shaft shall have a Teflon coating and all shaft bearing surfaces shall be made of Teflon. The pressure independent springs shall be made of stainless steel. SPEC WRITER NOTE: In addition to the above paragraph; p
45、rovide the following paragraph if working in highly corrosive environments. G. The airflow device shall have no exposed aluminum or stainless steel components. The shaft support brackets, pivot arm, internal mounting link, and pressure independent springs shall have a baked-on corrosion resistant ph
46、enolic coating. Internal nuts, bolts, and rivets shall be titanium or phenolic coated stainless steel. H. Constant volume units: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-10 23 36 00 - 8 1. Actuator to be factory mounted to the valve. 2. Clo
47、sed loop control of airflow by way of flow feedback signal with less than 1 second response time. 3. Shaft positioned using direct potentiometer measurement to produce a linear factory calibrated feedback. 4. The maximum and minimum airflows shall be as scheduled. I. Variable volume units: 1. Actuat
48、or to be factory mounted to the valve. 2. Closed loop control of airflow by way of flow feedback signal with less than 1 second response time. 3. Shaft positioned using direct potentiometer measurement to produce a linear factory calibrated feedback. J. Certification: 1. Control device: factory cali
49、brated to airflows detailed on plans using NIST traceable air stations and instrumentation having a combined accuracy of plus or minus 1% of signal over the entire range of measurement. 2. Electronic airflow control devices: further calibrated and their accuracy verified to plus or minus 5% of signal at a minimum of eight different airflows across the full operating range
