1、03-01-12 08 71 00-1 SECTION 08 71 00 DOOR HARDWARE SPEC WRITER NOTE: Delete between / - / if not applicable to project. Also delete any other item or paragraph not applicable in the section and renumber the paragraphs. PART 1 - GENERAL 1.1 DESCRIPTION A. Door hardware and related items necessary for
2、 complete installation and operation of doors. 1.2 RELATED WORK A. Caulking: Section 07 92 00 JOINT SEALANTS. B. Application of Hardware: / Section 08 14 00, WOOD DOORS / Section 08 11 13, HOLLOW METAL DOORS AND FRAMES / Section 08 17 10, INTEGRATED DOOR ASSEMBLIES / Section 08 41 13, ALUMINUM-FRAME
3、D ENTRANCES AND STOREFRONTS / Section 08 42 33, REVOLVING DOOR ENTRANCES / Section 08 33 00, COILING DOORS AND GRILLES / Section 08 33 13, COILING COUNTER DOORS / Section 08 34 36, DARKROOM DOORS / Section 08 34 53, SECURITY DOORS AND FRAMES / Section 08 34 73, SOUND CONTROL DOOR ASSEMBLIES / Sectio
4、n 08 42 23, INTENSIVE CARE UNIT/CRITICAL CARE UNIT (ICU/CCU) ENTRANCES / Section 08 42 29, AUTOMATIC ENTRANCES / Section 08 71 13, AUTOMATIC DOOR OPERATORS /Section 08 71 13.11, LOW ENERGY DOOR OPERATORS / Section 13 49 00, RADIATION PROTECTION / Section 32 31 33, CHAIN LINK FENCES AND GATES / and S
5、ection 32 31 19, DECORATIVE METAL FENCES AND GATES / C. Finishes: Section 09 06 00, SCHEDULE FOR FINISHES. D. Painting: Section 09 91 00, PAINTING. E. Card Readers: Section 28 13 11, PHYSICAL ACCESS CONTROL SYSTEMS. F. Electrical: Division 26, ELECTRICAL. G. Fire Detection: Section 28 31 00, FIRE DE
6、TECTION AND ALARM. 1.3 GENERAL A. All hardware shall comply with UFAS, (Uniform Federal Accessible Standards) unless specified otherwise. B. Provide rated door hardware assemblies where required by most current version of the International Building Code (IBC). C. Hardware for Labeled Fire Doors and
7、Exit Doors: Conform to requirements of NFPA 80 for labeled fire doors and to NFPA 101 for exit doors, as well as to other requirements specified. Provide hardware listed by UL, except where heavier materials, large size, or better grades are Provided by IHSNot for ResaleNo reproduction or networking
8、 permitted without license from IHS-,-,-03-01-12 08 71 00-2 specified herein under paragraph HARDWARE SETS. In lieu of UL labeling and listing, test reports from a nationally recognized testing agency may be submitted showing that hardware has been tested in accordance with UL test methods and that
9、it conforms to NFPA requirements. SPEC WRITER NOTE: The word “FIRE“ must be included as part of the certification on the Underwriters Laboratories label on exit devices to be used on fire doors. D. Hardware for application on metal and wood doors and frames shall be made to standard templates. Furni
10、sh templates to the fabricator of these items in sufficient time so as not to delay the construction. E. The following items shall be of the same manufacturer, except as otherwise specified: 1. Mortise locksets. 2. Hinges for hollow metal and wood doors. 3. Surface applied overhead door closers. 4.
11、Exit devices. 5. Floor closers. 1.4 WARRANTY A. Automatic door operators shall be subject to the terms of FAR Clause 52.246-21, except that the Warranty period shall be two years in lieu of one year for all items except as noted below: 1. Locks, latchsets, and panic hardware: 5 years. 2. Door closer
12、s and continuous hinges: 10 years. 1.5 MAINTENANCE MANUALS A. In accordance with Section 01 00 00, GENERAL REQUIREMENTS Article titled “INSTRUCTIONS“, furnish maintenance manuals and instructions on all door hardware. Provide installation instructions with the submittal documentation. 1.6 SUBMITTALS
13、 A. Submittals shall be in accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA AND SAMPLES. Submit 6 copies of the schedule per Section 01 33 23. Submit 2 final copies of the final approved schedules to VAMC Locksmith as record copies (VISN Locksmith if the VAMC does not have a locksmith).
14、 B. Hardware Schedule: Prepare and submit hardware schedule in the following form: Hardware Quantity Size Reference Publication Finish Mfr. Name Key Control UL Mark (if ANSI/BHMA Finish Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-01-12 08 71 0
15、0-3 Item Type No. and Catalog No. Symbols fire rated and listed) Designation C. Samples and Manufacturers Literature: 1. Samples: All hardware items (proposed for the project) that have not been previously approved by Builders Hardware Manufacturers Association shall be submitted for approval. Tag a
16、nd mark all items with manufacturers name, catalog number and project number. 2. Samples are not required for hardware listed in the specifications by manufacturers catalog number, if the contractor proposes to use the manufacturers product specified. D. Certificate of Compliance and Test Reports: S
17、ubmit certificates that hardware conforms to the requirements specified herein. Certificates shall be accompanied by copies of reports as referenced. The testing shall have been conducted either in the manufacturers plant and certified by an independent testing laboratory or conducted in an independ
18、ent laboratory, within four years of submittal of reports for approval. 1.7 DELIVERY AND MARKING A. Deliver items of hardware to job site in their original containers, complete with necessary appurtenances including screws, keys, and instructions. Tag one of each different item of hardware and deliv
19、er to Resident Engineer for reference purposes. Tag shall identify items by Project Specification number and manufacturers catalog number. These items shall remain on file in Resident Engineers office until all other similar items have been installed in project, at which time the Resident Engineer w
20、ill deliver items on file to Contractor for installation in predetermined locations on the project. 1.8 PREINSTALLATION MEETING A. Convene a preinstallation meeting not less than 30 days before start of installation of door hardware. Require attendance of parties directly affecting work of this sect
21、ion, including Contractor and Installer, Architect, Project Engineer and VA Locksmith, Hardware Consultant, and Hardware Manufacturers Representative. Review the following: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-01-12 08 71 00-4 1. Inspec
22、tion of door hardware. 2. Job and surface readiness. 3. Coordination with other work. 4. Protection of hardware surfaces. 5. Substrate surface protection. 6. Installation. 7. Adjusting. 8. Repair. 9. Field quality control. 10. Cleaning. 1.9 INSTRUCTIONS A. Hardware Set Symbols on Drawings: Except fo
23、r protective plates, door stops, mutes, thresholds and the like specified herein, hardware requirements for each door are indicated on drawings by symbols. Symbols for hardware sets consist of letters (e.g., “HW“) followed by a number. Each number designates a set of hardware items applicable to a d
24、oor type. SPEC WRITER NOTE: Delete following paragraph if new hospital station, or where existing station is to be rekeyed. /B. Keying: All cylinders shall be keyed into existing _ / Great / Grand Master Key System /. Provide removable core cylinders that are removable only with a special key or too
25、l without disassembly of knob or lockset /. Cylinders shall be / 6 / 7 / pin type. Keying information shall be furnished at a later date by the Resident Engineer./ SPEC WRITER NOTE: When the project requires a new keying system, include following paragraph. For projects at existing hospitals use abo
26、ve paragraph. C. Keying: A new Great Grandmaster key shall be established for this project. The key system shall be small format (Best size and profile) removable core type as previously described. The key blanks shall be protected by a utility patent with a minimum seven years remaining on the pate
27、nt from the start of construction, and protected by contract-controlled distribution. The manufacturer shall furnish code pattern listings in both paper and electronic formats so keys may be reproduced by code.; provide electronic format in file type required by projects key control software. The ma
28、nufacturer shall design the new key system with the capacity to rekey the existing system and also provide for 25 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-01-12 08 71 00-5 percent expansion capability beyond this requirement. Submit a keyin
29、g chart for approval showing proposed keying layout and listing expansion capacity. 1. Keying information will be furnished to the Contractor by the Resident Engineer. 2. Supply information regarding key control of cylinder locks to manufacturers of equipment having cylinder type locks. Notify Resid
30、ent Engineer immediately when and to whom keys or keying information is supplied. Return all such keys to the Resident Engineer. SPEC WRITER NOTE: Contractor shall verify with the station personnel, the location of key identification to be stamped on cylinders. 1.10 APPLICABLE PUBLICATIONS A. The pu
31、blications listed below form a part of this specification to the extent referenced. The publications are referenced in the text by the basic designation only. In text, hardware items are referred to by series, types, etc., listed in such specifications and standards, except as otherwise specified. B
32、. American Society for Testing and Materials (ASTM): F883-04 Padlocks E2180-07Standard Test Method for Determining the Activity of Incorporated Antimicrobial Agent(s) In Polymeric or Hydrophobic Materials C. American National Standards Institute/Builders Hardware Manufacturers Association (ANSI/BHMA
33、): A156.1-06 Butts and Hinges A156.2-03 Bored and Pre-assembled Locks and Latches A156.3-08 Exit Devices, Coordinators, and Auto Flush Bolts A156.4-08 Door Controls (Closers) A156.5-01 Auxiliary Locks and Associated Products A156.6-05 Architectural Door Trim A156.8-05 Door Controls-Overhead Stops an
34、d Holders A156.12-05 .Interconnected Locks and Latches A156.13-05 . Mortise Locks and Latches Series 1000 A156.14-07 .Sliding and Folding Door Hardware Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-01-12 08 71 00-6 A156.15-06 . Release Devices-C
35、loser Holder, Electromagnetic and Electromechanical A156.16-08 . Auxiliary Hardware A156.17-04 .Self-Closing Hinges and Pivots A156.18-06 . Materials and Finishes A156.20-06 .Strap and Tee Hinges, and Hasps A156.21-09 . Thresholds A156.22-05 . Door Gasketing and Edge Seal Systems A156.23-04 . Electr
36、omagnetic Locks A156.24-03 . Delayed Egress Locking Systems A156.25-07 .Electrified Locking Devices A156.26-06 . Continuous Hinges A156.28-07 .Master Keying Systems A156.29-07 .Exit Locks and Alarms A156.30-03 .High Security Cylinders A156.31-07 Electric Strikes and Frame Mounted Actuators A250.8-03
37、 Standard Steel Doors and Frames D. National Fire Protection Association (NFPA): 80-10 Fire Doors and Fire Windows 101-09 . Life Safety Code E. Underwriters Laboratories, Inc. (UL): Building Materials Directory (2008) PART 2 - PRODUCTS SPEC WRITER NOTE: Under “Hardware Sets“, schedule special hinges
38、 for doors over 1200 mm (4 feet) wide and other special doors. Also schedule special hinges such as spring hinges and strap hinges. 2.1 BUTT HINGES A. ANSI A156.1. Provide only three-knuckle hinges, except five-knuckle where the required hinge type is not available in a three-knuckle version (e.g.,
39、some types of swing-clear hinges). The following types of butt hinges shall be used for the types of doors listed, except where otherwise specified: 1. Exterior Doors: Type A2112/A5112 for doors 900 mm (3 feet) wide or less and Type A2111/A5111 for doors over 900 mm (3 feet) wide. Hinges for exterio
40、r outswing doors shall have non-removable pins. Hinges for exterior fire-rated doors shall be of stainless steel material. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-01-12 08 71 00-7 2. Interior Doors: Type A8112/A5112 for doors 900 mm (3 fee
41、t) wide or less and Type A8111/A5111 for doors over 900 mm (3 feet) wide. Hinges for doors exposed to high humidity areas (shower rooms, toilet rooms, kitchens, janitor rooms, etc. shall be of stainless steel material. B. Provide quantity and size of hinges per door leaf as follows: 1. Doors up to 1
42、210 mm (4 feet) high: 2 hinges. 2. Doors 1210 mm (4 feet) to 2260 mm (7 feet 5 inches) high: 3 hinges minimum. 3. Doors greater than 2260 mm (7 feet 5 inches) high: 4 hinges. 4. Doors up to 900 mm (3 feet) wide, standard weight: 114 mm x 114 mm (4-1/2 inches x 4-1/2 inches) hinges. 5. Doors over 900
43、 mm (3 feet) to 1065 mm (3 feet 6 inches) wide, standard weight: 127 mm x 114 mm (5 inches x 4-1/2 inches). 6. Doors over 1065 mm (3 feet 6 inches) to 1210 mm (4 feet), heavy weight: 127 mm x 114 mm (5 inches x 4-1/2 inches). 7. Provide heavy-weight hinges where specified. 8. At doors weighing 330 k
44、g (150 lbs.) or more, furnish 127 mm (5 inch) high hinges. C. See Articles “MISCELLANEOUS HARDWARE“ and “HARDWARE SETS“ for pivots and hinges other than butts specified above and continuous hinges specified below. 2.2 CONTINUOUS HINGES A. ANSI/BHMA A156.26, Grade 1-600. 1. Listed under Category N in
45、 BHMAs “Certified Product Directory.“ B. General: Minimum 0.120-inch- (3.0-mm-) thick, hinge leaves with minimum overall width of 4 inches (102 mm); fabricated to full height of door and frame and to template screw locations; with components finished after milling and drilling are complete C. Contin
46、uous, Barrel-Type Hinges: Hinge with knuckles formed around a Teflon-coated 6.35mm (0.25-inch) minimum diameter pin that extends entire length of hinge. 1. Base Metal for Exterior Hinges: Stainless steel. 2. Base Metal for Interior Hinges: /Stainless steel/ /Steel/ /Aluminum/. 3. Base Metal for Hing
47、es for Fire-Rated Assemblies: /Stainless steel/ /Steel/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-03-01-12 08 71 00-8 4. Provide with non-removable pin (hospital tip option) at lockable outswing doors. 5. Where required to clear adjacent casin
48、g, trim, and wall conditions and allow full door swing, provide wide throw hinges of minimum width required. 6. Provide with manufacturers cut-outs for separate mortised power transfers and/or mortised automatic door bottoms where they occur. 7. Where thru-wire power transfers are integral to the hi
49、nge, provide hinge with easily removable portion to allow easy access to wiring connections. 8. Where models are specified that provide an integral wrap-around edge guard for the hinge edge of the door, provide manufacturers adjustable threaded stud and machine screw mechanism to allow the door to be adjusted within the wrap-aroun
