1、09-11 03 51 13 - 1 SECTION 03 51 13 CEMENTITIOUS WOOD FIBER DECKS SPEC WRITE NOTES: 1. Delete between / _/ if not applicable to project. 2. Also delete any other item or paragraph not applicable in the section and renumber the paragraphs. 3. Listed by UL as structural cement-fiber units, and two man
2、ufacturers. PART 1 - GENERAL 1.1 DESCRIPTION Section specifies structural cement-fiber units (planks) for roof deck / and acoustical panels /. 1.2 SUBMITTALS A. Submit in accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES. B. Shop Drawings: 1. Cement-fiber unit deck installat
3、ion details and anchorage. 2. Show primary frames members and purlins with subpurline and opening framing. C. Manufacturers Literature and Data: 1. Cement-fiber units showing compliance with specifications including anchorage items and Installation instructions. 2. Subpurling. 3. Grout. D. Certifica
4、tes: Stating cement-fiber units meet fire hazard classification, wind uplift requirement, and “R“ values specified. 1.3 DELIVERY Deliver units to site labeled with manufacturers name, brand and contents. 1.4 STORAGE A. Store cement-fiber units and accessories in weathertight and dry storage facility
5、. B. Protect from damage from handling, water, weather, and construction operations before, during, and after installation. 1.5 APPLICABLE PUBLICATIONS A. Publications listed below form a part of this specification to extent referenced. Publications are referenced in text by basic designation only.
6、B. American Society for Testing and Materials (ASTM): A36/A36M-08 Structural Steel Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09-11 03 51 13 - 2 A653/A653M-10 Steel Sheet, Zinc Coated (Galvanized) or Zinc-Iron Alloy Coated (Galvannealed) by the
7、Hot-Dip Process C144-04 Aggregates for Masonry Mortar C150-09 Portland Cement C177-10 Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded Hot-Plate Apparatus C423-09 Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method C494-1
8、0 Chemical Admixtures for Concrete C1289-10 . Faced Rigid Cellular Polyisocynurate Thermal Insulation Board E84-10 . Surface Burning Characteristics of Building Materials E119-10 Fire Tests of Building Construction and Materials E1264-08 . Classification for Acoustical Ceiling Products F1667-10 . Dr
9、iven Fasteners: Nails, Spikes and Staples C. American Welding Society (): D1.1-10 Structural Welding Code Steel D. Factory Mutual Engineering and Research Corporation (FM): Annual issue . Approval Guide Building Materials E. Underwriters Laboratories, Inc. (UL): Annual issue . Building Materials Dir
10、ectory Annual issue . Fire Resistance Directory F. Warnock Heresy (WH): Annual issue . Certification Listings G. Federal Specifications (Fed. Spec.): FF-S-107C(2) . Screws, Tapping and Drive SPEC WRITER NOTES: 1. Make material requirements agree with applicable requirements specified in the referenc
11、ed Applicable Publications. 2. Update and specify only that which applies to the project. 3. Coordinate roof deck design with structural Engineer to show assembly required and section editing. 4. Coordinate details when units are used for acoustical panels. PART 2 - PRODUCTS 2.1 MATERIALS A. Portlan
12、d Cement: ASTM C150, Type I or III. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09-11 03 51 13 - 3 B. Chemical Admixtures: ASTM C494, type as required by unit manufacturer. C. Aggregate: ASTM C144. D. Wood fiber: 1. Wood species: Unit manufacture
13、rs standard softwood. 2. Shredded into strips; random lengths unit manufacturers standard specifications. 3. Treated for fire resistance. E. Fasteners: 1. Nails: ASTM F1667, galvanized, roof type with integral 25 mm (1-inch) washers length to provide 76 mm (1-1/2-inches) penetration into wood suppor
14、t, type as required by unit manufacturer. 2. Screws: Fed. Spec FF-S-107 type as required by unit manufacturer. a. Provide 25 mm (1-inch) wide washers when screw retains unit. b. Provide 26 mm (1-1/2-inch) minimum penetration into wood. SPEC WRITER NOTE: Specify physical properties of bulb tees used
15、on project. Design deflection: 1/360 of span. F. Bulb-Tee Subpurlins: 1. Fabricated from ASTM A36 steel. 2. Minimum flange bearing area each side: 50 mm (1-inch). 3. Rust inhibiting paint finish, manufacturers standard. 4. Properties: a. Minimum weight per 0.304 mm (lineal foot: _ Kg (_ pounds) b. H
16、eight: _ MM (_inches): c. Minimum resisting moment: _ MM (_ inch pound). 5. Length to span not less than three supports. G. Clips and Channels: 1. Fabricated of ASTM A446 steel sheet. 2. Thickness: Minimum 1.61 mm (0.0635-inches) for channels 1.31 mm (0.0516-inch) for clips. 3. Clips: a. Two piece o
17、r single piece. b. Purlin anchor clamp designed to fasten to purlin and engage channel. c. Channel to engage purlin anchor clamp and hold down unit in groove. d. Z clamp, flange for anchoring to purlin, other flange for engaging groove. e. Clips provide uplift resistance of not less than 1-1/2 N (25
18、0 pounds). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09-11 03 51 13 - 4 4. Channels: a. Fabricated to fit tongue and groove of units. b. Length to span between purlins with continuous span over three or more purlins, ends over purlin supports.
19、H. Water: Clean and potable, free from imparities detrimental to grout. I. Grout Mix: 1. Portland Cement aggregate water and admixture in proportions required by unit manufacture. 2. Mix in mechanically operated mortar mixer. Minimum 3 minutes, Maximum 5 minutes. 3. Mix to pouring consistency. 2.2 S
20、TRUCTURAL CEMENT-FIBER UNITS A. Labeled for fire resistance by FM, UL, or WH. 1. Flame spread: Maximum 25. 2. Smoke Developed: Not laminated to other products; maximum 5. 3. Tested per ASTM E84. B. Manufacture planks from treated wood fibers and portland cement, bonded under pressure. C. Having foll
21、owing properties: 1. Long edges tongue and groove. / Provide rebated edges at bulb tee bearing flange use. 2. Ends square unless shown otherwise. 3. Plank length to span two supports except for end fillers or bulb tee supports. 4. Thermal Resistance: a. Test in accordance with ASTM C177. b. “R“ valu
22、e: / 38 mm (1-1/2-inches) thick 2.63, /. 51 mm (2-inches) thick, 3.5, /. 64 mm (2-1/2-inches thick, 4.38, / and /. 76 mm (3-inches) thick, 5.25 /. /c. R“ value _ insulation layer over units. / 5. Noise Reduction Coefficient (NRC): a. Tested in accordance with ASTM C423. b. NRC Not less than: / 38 mm
23、 (1-1/2-inches) thick, 0.55 /. 51 mm (2-inches) thick 0.60 /. 64 mm (2-1/2-inches) thick 0.60 / and / 76 mm (3-inches) thick 0.65 /. SPEC WRITER NOTE: Do not use units with insulation bonded to units where vapor retarder is required on insulation joint Provided by IHSNot for ResaleNo reproduction or
24、 networking permitted without license from IHS-,-,-09-11 03 51 13 - 5 line. Use R of 5.56 per 25.4 mm (inch) for calculating thickness of insulation. 6. Factory bond ASTM C1289 layer of polyisocyanurate insulation to top plank. a. Thickness of insulation as shown. b. Top of insulation faced with gla
25、ss fiber felt. SPEC WRITER NOTES: 1. Verify details. Show system selected and applicable components of system. 2. Check manufacturers literature for available thicknesses required to suit span and live load, and corresponding “R“ value, NRC, subpurlin and channel size, where applicable. 3. Design sy
26、stem for not less than l/240, preferred l/360, deflection. 4. Design system for wind uplift in accordance with FM 1-28. 5. Structural Engineer to design roof system. 6. Support edges and ends of units at openings greater than 200 mm (8-inches). 7. Size depth of bulb tees for not less than 13 mm (1/2
27、-inch) grout over top of bulb and flush with surface of unit. PART 3 - EXECUTION 3.1 INSTALLATION /A. Bulb tees: 1. Place bulb tees at spacing shown, aligned and straight. 2. Weld bulb tees to primary framing as shown. / B. Plank Installation: 1. Do not use broken or cracked units. 2. Cut planks to
28、fit tight at perimeter, vertical surfaces, projections, / openings / ridges / valleys /. 3. Bear edges and ends of planks and at perimeter of openings greater than 200 mm (8-inches) on framing members, / and bearing walls / not less 25 mm (1-inch). 4. Installing Units: a. Lay continuous units progre
29、ssively with side joints (edges) tightly butted and with end joints in adjacent rows staggered. Install with tongue leading. b. Nail or screw units to bearing surface. Space fasteners at 125 mm (5-inches) between edge or corner fasteners. Unless specified otherwise. c. Weld clips to steel joists or
30、beam; engaging clip into groom of units. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09-11 03 51 13 - 6 d. Install fasteners as unit is layed. Do not walk on unfastened units. e. Lay units with edges bearing not less than 25 mm (1-inch) on bottom
31、 flange of bulb tees. f. Grout bulb tee joints with units to finish flush with top of units. C. Install barrier, full depth of plank / plus insulation /, over top of sound rated partitions / of exterior wall / as shown. / 3.2 PROTECTION Provide planking or plywood to distribute weight and support heavy material placed or transported over the roof deck. - - - E N D - - - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
