欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE ARP 712B-2004 Galley Lighting《空厨照明》.pdf

    • 资源ID:1023293       资源大小:83.95KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE ARP 712B-2004 Galley Lighting《空厨照明》.pdf

    1、 AEROSPACE RECOMMENDED PRACTICE Galley Lighting SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, i

    2、ncluding any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2004 SAE International All

    3、rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside U

    4、SA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org Issued 1965-05 Revised 2004-03 Superseding ARP712A ARP712 REV.B FOREWORD Changes in this revision are format/editorial only. 1. SCOPE: This SAE Aerospace Recommended Practice (AR

    5、P) provides minimum standards and environmental design requirement recommendations for lighting and control in galley areas. It also addresses electrical shock hazard in galley areas. 1.1 Purpose: The purpose of this recommended practice is to provide minimum standards for the illumination of galley

    6、s (buffets) and for the location of lighting controls within the galley area of passenger transport aircraft. 2. DEFINITION: Galley lighting is the lighting that is provided within the galley area. Galley lighting should provide sufficient illumination for the preparation and serving of food, the re

    7、ading of instruction manuals, and the identification and operation of the various controls and equipment located in the galley. 3. RECOMMENDATIONS: 3.1 Lighting Levels: 3.1.1 Average of 53.8 1x (5.0 ft-c) of illumination should be provided on the floor of the galley area. Copyright SAE International

    8、 Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP712 Revision B - 2 - 3.1.2 Average of 161.4 to 215.2 1x (15.0 to 20.0 ft-c) of illumination should be provided on working surfaces such as counter tops. 3.1.3 Average of 1

    9、0.76 1x (1.0 ft-c) should be provided on the floor of deep compartments, such as ovens, and storage bins, which must be inspected. 3.1.4 Average of 53.8 1x (5.0 ft-c) of illumination should be provided on all controls, operating instructions, and placards. 3.1.5 The galley area lighting should be pr

    10、ovided with dimming controls, either continuous or stepped dimming, to reduce the illumination while operating under dark conditions. 3.1.6 The color of the galley light sources should be white. 3.2 General: 3.2.1 Lighting Location: Light sources should be carefully located to minimize the casting o

    11、f shadows on work areas by personnel occupying normal work positions. Light from the galley area should be confined to that area by directional light sources or by curtains around the galley area. Light sources should be located and trim materials selected to minimize glare in the eyes of an attenda

    12、nt working in the galley. 3.2.2 Controls: All controls within the galley area should be so located or protected as to prevent injury to an attendant in the event of a violent airplane movement. 3.2.2.1 All lighting controls within the galley area should be placed on a single control panel and locate

    13、d within convenient reach of the attendant. Individual controls shall be arranged to conform generally to the physical location of the light sources. Light controls for continuous dimming shall rotate clockwise to increase intensity and shall provide an “off“ position at the extreme of counter-clock

    14、wise rotation. For step dimming or on/off control, the toggle controls shall be full bright/on in the up position. 3.2.2.2 Incandescent lamps should be operated at not more than 90% rated voltage to extend lamp life. Operation at 90% rated voltage will result in four times rated lamp life. Long life

    15、 lamps (rated for 2000 h or more) should be operated at not more than 95% rated voltage. 3.2.2.3 Ballast and transformers should contain replaceable fuses or other circuit protectors to prevent overheating and smoke. If fuses are used, replacement fuses should be available. 3.2.3 Fixture Temperature

    16、: While installed, no exposed lighting fixture surface should exceed a stabilized temperature of 65.5C (150F) with an ambient temperature of 23.8C (75F). Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,

    17、-,-SAE ARP712 Revision B - 3 - 3.2.4 Fixture Bonding: All exposed metal surfaces should be electrically bonded to airframe structure to prevent electrical shock hazard to personnel. 3.2.4.1 If input voltage to the fixture exceeds 30 V, an electrical ground should be provided. 3.2.5 Maintenance: Cons

    18、istent with general galley design, lighting fixtures should be designed and fabricated to provide smooth, easily cleanable surfaces with a minimum of cracks and crevices. 3.2.6 Material and Workmanship: All galley lighting fixtures and equipment should be designed and qualified for reliable operatio

    19、n, under the applicable aircraft environment, throughout the life of the aircraft. Materials and workmanship should be consistent with the best manufacturing practice for aircraft equipment and accessories. Design should be such that noise from vibrating parts is minimized. 3.2.7 Lamp Replacement: A

    20、ll lamps should be readily replaceable without the use of special tools. When opened for re-lamping, the replacement lamp part number should be clearly visible in all lighting fixtures. The manufacturers name and part number shall be clearly visible to maintenance personnel, on all lighting fixtures

    21、. The type of lamps used in the galley should be consistent with the type of lamps used throughout the airplane. 3.2.8 EMI: All lighting fixtures should meet the applicable electromagnetic interference requirements of Radio Technical Commission for Aeronautics (RTCA) Document No. DO-160B. 3.2.9 Envi

    22、ronmental Conditions: Radio Technical Commission for Aeronautics performance should be determined and testing accomplished in accordance with applicable environmental conditions of RTCA Document No. DO-160B. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduct

    23、ion or networking permitted without license from IHS-,-,-SAE ARP712 Revision B - 4 - 3.2.10 Electric Shock Hazard: To reduce the possibility of electric shock to crew and maintenance personnel, lighting equipment, which has exposed electrically conductive (metal) surfaces, should have the following:

    24、 a) All electric circuits isolated from the case. b) All electrical terminations covered to prevent inadvertent shorting or personnel contact. c) All metal components electrically connected to a bonding stud so that chasis to (earth) ground may be accomplished with a separate wire. 4. OTHER CONSIDER

    25、ATIONS: The lighting should comply with the design goals and other considerations as recommended in AIR512A. PREPARED UNDER THE JURISDICTION OF SAE SUBCOMMITTEE A-20A/C, CREW STATION & INTERIOR LIGHTING OF COMMITTEE A-20, AIRCRAFT LIGHTING Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(SAE ARP 712B-2004 Galley Lighting《空厨照明》.pdf)为本站会员(Iclinic170)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开