欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE ARP 1360A-2001 Detection of Chloride and Bromide Contamination of Electronic Equipment《电子设备氯化物和溴化物污染的检测》.pdf

    • 资源ID:1022757       资源大小:48.55KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE ARP 1360A-2001 Detection of Chloride and Bromide Contamination of Electronic Equipment《电子设备氯化物和溴化物污染的检测》.pdf

    1、AEROSPACERECOMMENDEDPRACTICEARP1360REV.AIssued 1975-06ReaffirmedRevised 2001-04Superseding ARP1360Detection of Chloride and Bromide Contamination of Electronic Equipment1. SCOPE:1.1 Purpose:This recommended practice covers a test for detecting residual chlorides and bromides on electronicequipment.1

    2、.2 The detailed procedures noted herein are based on laboratory and production experience and reflect those design practices and fabrication procedures, such as wave soldering, that require the use of activated flux for solder connections. This procedure has been used as a means of satisfying the in

    3、tent of MIL-STD-454, Requirement 5, which permits the use of only R or RMA flux.1.3 Application:Primarily to establish qualitatively and quickly the effectiveness of cleaning processes used during production operations to remove chloride and bromide contamination.2. PREPARATION OF SOLUTIONS:2.1 Chlo

    4、ride and/or Bromide-Free Water:Rinse water shall be distilled or deionized water having resistivity not lower than 1 megohm-cm, measured using an in-line cell.2.2 Silver Nitrate Solution:Shall be approximately 5% by weight silver nitrate in chloride/bromide-free water containing 1 mL of 70% nitric a

    5、cid per liter of solution.20 0310-SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any p

    6、atent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserve

    7、d. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)

    8、 Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/ARP1360ACopyright SAE International Provided by IHS under license

    9、with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP1360 Revision A- 2 -3. PROCEDURE:3.1 Rinse surfaces to be tested with water meeting the requirements of 2.1, adjusting quantity of water used as required to rinse desired amount of surface area. Quantit

    10、y of rinse water should be kept to a minimum. Drops of rinse water may be used on small, localized areas.3.2 Drain rinse water into suitable glassware that has been adequately rinsed with water in accordance with 2.1 or, in case small amounts of rinse water are used, transfer rinse water by means of

    11、 clean pipette or dropper to a properly rinsed test tube or black spot plate.3.3 Large quantities of rinse water may be reduced in volume to increase test sensitivity by boiling off excess water.3.4 Add silver nitrate solution (see 2.2) at a ratio of one drop of reagent per 200 mL of rinse water. In

    12、 a darkened room, beam a focusable spot light through the glass beaker containing the rinse solution. Examine for turbidity, using Tyndall effect by observing at right angles to the beam, against a dull black background. Rinse water shall be considered bromide and chloride-free if no turbidity appea

    13、rs within two minutes.3.4.1 The standard used for turbidity comparison shall be the source water used for rinsing, with the silver nitrate test solution added as in the chloride test, and contained in glassware or spot plate of the same diameter as used in the actual test.3.4.2 Because of the high s

    14、ensitivity of this test when run in a darkened room, the exterior of the glassware must be clean in order to avoid light-scattering which could interfere with chloride haze observation.4. NOTES:4.1 The change bar ( l ) located in the left margin is for the convenience of the user in locating areas w

    15、here technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical revisions. Change bars and (R) are not used in original publications, n

    16、or in specifications that contain editorial changes only.4.2 Processes involving use of solutions or compounds containing chlorides and/or bromides, such as soft soldering, etching, and plating, must be followed by adequate cleaning to ensure removal of chlorides and bromides. Electronic assemblies

    17、are subject to contamination during all phases of manufacturing and testing and must be properly cleaned prior to conformal coating and final assembly, after which further cleaning for the removal of ionic contamination is not possible. Subject testing can be used to determine the presence of contam

    18、ination at various stages of assembly and thereby ensure chloride and bromide-free final assemblies.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE ARP1360 Revision A- 3 -4.3 ARP1332 contains a s

    19、imilar chloride ion test which requires a 24-hour waiting period between sampling and measuring. This method requires only two minutes between sampling and measuring and is more adaptable to production line operations.PREPARED UNDER THE JURISDICTION OFAMS COMMITTEE “B”Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(SAE ARP 1360A-2001 Detection of Chloride and Bromide Contamination of Electronic Equipment《电子设备氯化物和溴化物污染的检测》.pdf)为本站会员(visitstep340)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开