欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 2521C-2001 Coating Reflection-Reducing for Instrument Glasses《反射减少用于减少反射涂料的仪器玻璃》.pdf

    • 资源ID:1020684       资源大小:74.27KB        全文页数:8页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 2521C-2001 Coating Reflection-Reducing for Instrument Glasses《反射减少用于减少反射涂料的仪器玻璃》.pdf

    1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

    2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p

    3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

    4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS2521C AEROSPACE MATERIAL SPECIFICATION AMS2521 REV. C Issued 1967-11 Revised 2

    5、001-04 Reaffirmed 2013-11 Superseding AMS2521B Coating, Reflection-Reducing for Instrument Glasses RATIONALE AMS2521C has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE:1.1 Form: This specification covers optical-quality coatings applied to instrument glasses.1.2 Applicatio

    6、n: This coating has been used typically to reduce the intensity of reflection from the surfaces of instrument glasses and to increase light transmission through the glasses, but usage is not limited to such applications.2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the d

    7、ate of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been canceled and no superseding document has been specified, the

    8、last published issue of that document shall apply.2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.ARP924 Specification and Inspection of Glass for Integrally Lighted Aerospace InstrumentsSAE INTERNATIONAL AMS2521C Page 2 of 8 2.2 ASTM Publications: Availab

    9、le from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.ASTM B 117 Operating Salt Spray (Fog) Testing ApparatusASTM D 1003 Haze and Luminous Transmittance of Transparent PlasticsASTM E 11 Wire-Cloth Sieves for Testing PurposesASTM G 21 Determining Resistance of Synthetic Polymeric Mate

    10、rials to Fungi2.3 U.S. Government Publications: Available from DODSSP, Subscription Services Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.MIL-E-12397 Eraser, Rubber-Pumice (for Testing Coated Optical Elements)MIL-STD-1241 Optical Terms and Definitions2.4 U.S. Army Drawings: Ava

    11、ilable from Commander, U.S. Army, TACOM-ARDEC, Attn: AMSTA-AR-QAW-E, Picitinnay Arsenal, NJ 07806-5000.D7680606 Coating, Eraser Abrasion Tester3. TECHNICAL REQUIREMENTS: 3.1 Material: The composition of the coating material shall be optional with the coating vendor.3.2 Properties of the Applied Coat

    12、ings: The coating, applied to substrate materials having indices of refraction within the range 1.47 to 1.55, shall conform to the following requirements. Tests shall be performed on the coated parts or on coated glass witness specimens of the same index of refraction and surface finish as the subst

    13、rate for the coated parts, coated in the same evaporation run as the parts, and positioned in the chamber so as to represent the optical and durability characteristics of the parts.3.2.1 Spectral Properties: 3.2.1.1 Specular Reflectance: The specular reflectance from each coated surface, measured wi

    14、th a calibrated spectrophotometer as defined in ASTM D 1003, shall not exceed the following limits for energy incident on the surface at the angles shown in Table 1.SAE INTERNATIONAL AMS2521C Page 3 of 8 3.2.1.2 Light Absorption: Within the wavelength range 425 to 700 millimicrons (nm), light loss s

    15、hall not exceed the limits per surface shown in Table 2, determined with a calibrated spectrophotometer as defined in ASTM D 1003:3.2.2 Durability: The coating, subjected to the adhesion test of 4.5.1 followed by the abrasion resistance test of 4.5.2, shall show no evidence of peeling, flaking, crac

    16、king, crazing, or delamination and shall have no change in spectral characteristics resulting in nonconformance to the requirements of 3.2.1.3.2.3 Environmental Resistance: The coating shall show no change in spectral characteristics resulting in nonconformance to the requirements of 3.2.1 after exp

    17、osure to any of the following:3.2.3.1 Elevated temperature in accordance with 4.5.3.3.2.3.2 Sand and dust in accordance with 4.5.4.3.2.3.3 Fungus in accordance with 4.5.5.3.2.3.4 Thermal shock in accordance with 4.5.6.3.2.3.5 Continuous exposure to salt spray in accordance with ASTM B 117 for not le

    18、ss than 50 hours.3.2.3.6 Humidity in accordance with 4.5.7. After exposure, the coating, lighted and inspected in accordance with ARP924, shall show no evidence of a cloudy or hazy appearance.TABLE 1 - Specular ReflectanceWavelength RangeMillimicrons (nm)Reflectance, %, maximumFor Angle of Incidence

    19、 Shown0 to 15 degrees, inclReflectance, %, maximumFor Angle of Incidence Shown30 degrees 0.5450 to 675, incl 0.6 absolute -450 to 650, incl - 1.0 absolute500 to 620, incl 0.35 average 0.50 average425 to 700, incl 0.35 average 0.50 averageTABLE 2 - Light Loss LimitsValue PercentMaximum average absorp

    20、tion 0.5%Maximum absolute absorption 2.0%SAE INTERNATIONAL AMS2521C Page 4 of 8 3.3 Quality: The coating, as received by purchaser, shall be uniform in quality and condition, smooth, and free from foreign materials and from physical and optical imperfections detrimental to performance of parts, dete

    21、rmined in accordance with ARP924.3.3.1 Surface Imperfections: Imperfections in the clear aperture area of the coating, as defined in MIL-STD-1241, shall not exceed the limits, shown in Table 3, evaluated in accordance with ARP924:4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: Th

    22、e vendor of the coating shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the coating conforms to the requirements of this speci

    23、fication.4.2 Classification of Tests: 4.2.1 Acceptance Tests: Specular reflectance (3.2.1.1), light absorption (3.2.1.2), durability (3.2.2), salt spray resistance (3.2.3.5), humidity resistance (3.2.3.6), and quality (3.3) are acceptance tests and shall be performed on each lot.4.2.2 Preproduction

    24、Tests: All technical requirements of this specification are classified as preproduction tests and shall be performed prior to or on the initial shipment of coated parts to a purchaser, when a change in material and/or processing requires reapproval as in 4.4.2, and when purchaser deems confirmatory

    25、testing to be required.4.3 Sampling: Shall be not less than the following; a lot shall be all parts made of the basis material, coated in the same equipment in a single pump-down cycle, and presented for vendors inspection at one time.TABLE 3 - Surface Imperfection LimitsArticle Scratch SpatterPinho

    26、le,Void, or LintWindow #80 #50 #50Cover glass orcover wedge #60 #20 #40Lighting wedge #40 #20 #40SAE INTERNATIONAL AMS2521C Page 5 of 8 4.3.1 For Acceptance Tests: One part or one witness specimen for each requirement. 4.3.2 For Preproduction Tests: Thirty parts or witness specimens, five for each r

    27、equirement except that the durability and humidity resistance tests shall be performed on the same five specimens and all 30 specimens shall be inspected for conformance to quality requirements.4.4 Approval: 4.4.1 Sample coated parts shall be approved by purchaser before coated parts for production

    28、use are supplied, unless such approval be waived by purchaser. Results of tests on production coated parts shall be essentially equivalent to those on the approved samples.4.4.2 Vendor shall use ingredients, manufacturing procedures, processes, and methods of inspection on production coated parts wh

    29、ich are essentially the same as those used on approved sample parts. If necessary to make any change in ingredients, in type of equipment for processing, or in manufacturing procedures, vendor shall submit for reapproval a statement of the proposed changes in ingredients and/or processing and, when

    30、requested, sample coated parts. Production parts coated by the revised procedure shall not be shipped prior to receipt of reapproval.4.5 Test Methods: 4.5.1 Adhesion: Test specimens shall be clean and free from contaminants, including finger prints, that would affect the adhesion of the testing tape

    31、. A strip of pressure-sensitive tape, 1 inch (25 mm) in nominal width or approximately 2/3 of the least dimension of the test specimen if less than 1 inch (25 mm), shall be pressed firmly in contact across the entire coated surface. After 30 to 60 seconds the tape shall be removed quickly with a sna

    32、p action which exerts the greatest possible stripping effect on the surface.4.5.2 Abrasion Resistance: 4.5.2.1 Test Procedure: The coating shall be tested by holding a standard abrasion testing device in the hand and rubbing the coated surface with a standard eraser conforming to MIL-E-12397 mounted

    33、 in the holding device. A pressure of approximately 2.0 to 2.5 pounds force (8.9 to 11.1 N) shall be applied. Strokes of approximately 1 inch (25 mm) shall be made if the size of the element or specimen will permit it; smaller strokes for smaller specimens. All strokes shall be made on one path for

    34、20 complete strokes.4.5.2.2 Test Equipment: Assembly details of the Abrasion Tester may be obtained on written request from U.S. Army Armament Research and Development Command as indicated in 2.3. The only rubber eraser plug which is acceptable for this test is also available from the same source. A

    35、ll requests should make reference to Drawing D7680606.4.5.3 Elevated Temperature: Specimens shall be heated to 315 C 8 (599 F 14), held at temperature for not less than 15 minutes, and cooled to room temperature. Heating and cooling rates shall be not greater than 8 C (14 F) degrees per minute.SAE I

    36、NTERNATIONAL AMS2521C Page 6 of 8 4.5.4 Sand and Dust Resistance: 4.5.4.1 Test Chamber: The chamber shall consist of a dust-tight cabinet with the floor designed to permit the dust to fall into hoppers for recirculation. The facility shall be time-cycle-controlled to accomplish the exposure and shut

    37、down required. A blower and duster shall be provided to circulate the dust throughout the test chamber with the velocity and concentration outlined.4.5.4.2 Test Procedure: The test samples shall be placed in the test chamber and the sand and dust density raised to, and maintained at, 0.1 to 0.5 gram

    38、/cubic foot (3.5 to 17.7 g/m3) and velocity between 100 and 500 feet/minute (508 and 2540 mm/s) within the test space. The internal temperature of the test chamber shall be maintained at 25 C 5 (77 F 9) for not less than six hours then raised to and maintained at 70 C 3 (158 F 5) for not less than s

    39、ix hours additional. The relative humidity shall not exceed 30% at any time during the test. At the end of the exposure period, the sample shall be removed from the test chamber and allowed to cool to room temperature. Accumulated dust shall be removed by brushing, wiping, shaking, or blowing with c

    40、lean, dry air.4.5.4.3 Sand and Dust: Sand and dust used in the test shall be of angular structure and shall have characteristics as follows:4.5.4.3.1 Particle Size: Shall be as follows, determined using U.S. Standard Sieve Series or equivalent as defined in ASTM E 11:100% shall pass through a 100 me

    41、sh (150-m) sieve.98% 2 shall pass through a 140 mesh (106-m) sieve.98% 2 shall pass through a 200 mesh (75-m) sieve.75% 2 shall pass through a 325 mesh (44-m) sieve.4.5.4.3.2 Chemical Composition: Shall be as shown in Table 4, determined by wet chemical methods or by a method acceptable to purchaser

    42、:TABLE 4 - CompositionIngredient% by Weightminimum% by WeightmaximumSi02 97 99Fe203 - 2A1203 - 1Ti02 - 2Mg0 - 1Ignition - 2SAE INTERNATIONAL AMS2521C Page 7 of 8 4.5.5 Fungus Resistance: Testing shall be conducted in accordance with ASTM G 21, using one species of fungus from each of the groups show

    43、n in Table 5.4.5.6 Thermal Shock: Test specimens shall be heated to, and maintained at, 70 C 3 (158 F 5) for not less than one hour and immediately thereafter placed in direct contact with an ice cube at least one square inch (645 mm2) in area for not less than two minutes. 4.5.7 Humidity Resistance

    44、: Test specimens shall be exposed continuously for not less than 24 hours in an atmosphere of 98% 2 relative humidity at 50 C 2 (122 F 4).4.6 Reports: 4.6.1 The vendor of coated parts shall furnish with each shipment a report showing the results of tests to determine conformance to the acceptance te

    45、st requirements and stating that the coating conforms to the other technical requirements of this specification. This report shall include the purchase order number, AMS 2521C, vendors material or product designation, lot number, size or part number, and quantity.4.7 Resampling and Retesting: If any

    46、 specimen used in the above tests fails to meet the specified requirements, disposition of the product may be based on the results of testing three additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be cause for reje

    47、ction of the product represented. Results of all tests shall be reported.5. PREPARATION FOR DELIVERY: 5.1 Coated parts shall be handled and packaged in such a manner as will ensure that the required physical characteristics of the coating are preserved.TABLE 5 - Fungus SpeciesGroup OrganismAmerican

    48、TypeCulture Collection No.QuartermasterNumberI Chateomium globosumMyrothecium verrucaria62059095459460II Memneniella echinataAspergillus niger959762751225458III Aspergillus flavusAspergillus terreus1083610690122382jIV Penicillium citrinumPenicillium ochrochloron984991121226477SAE INTERNATIONAL AMS25

    49、21C Page 8 of 8 5.2 Packages of coated parts shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the coated parts to ensure carrier acceptance and safe delivery.6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision lett


    注意事项

    本文(SAE AMS 2521C-2001 Coating Reflection-Reducing for Instrument Glasses《反射减少用于减少反射涂料的仪器玻璃》.pdf)为本站会员(brainfellow396)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开