欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AIR 1392A-1998 Oxygen System Maintenance Guide《氧气系统维护指南》.pdf

    • 资源ID:1020021       资源大小:53.17KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AIR 1392A-1998 Oxygen System Maintenance Guide《氧气系统维护指南》.pdf

    1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

    2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p

    3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

    4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AIR1392A AEROSPACE INFORMATION REPORT AIR1392 REV. A Issued 1977-10 Revised 1998-

    5、12 Reaffirmed 2013-12 Superseding AIR1392 Oxygen System Maintenance Guide RATIONALE AIR1392A has been reaffirmed to comply with the SAE five-year review policy. FOREWORDChanges in this revision are format/editorial only.1. SCOPE:This document is intended to give general instructions and directions f

    6、or personnel performing maintenance and modification work on Oxygen Systems.2. REFERENCES:2.1 FAA/DOT Specifications and Documents Applicable to Aircraft Oxygen Systems:Advisory Circular 43.13-2 Oxygen System Installation2.2 SAE Documents Applicable to Aircraft Oxygen Systems:2.2.1 Aerospace Standar

    7、ds (AS):AS861 Minimum General Standards for Oxygen Systems2.2.2 Aerospace Information Reports (AIR):AIR822 Oxygen Systems for General Aviation AircraftAIR825A Oxygen Equipment for AircraftAIR1059 Transfilling and Maintenance of Oxygen CylindersAIR1176 Oxygen System and Component Cleaning and Packagi

    8、ngAIR1223 Installation of Liquid Oxygen Systems in Civil Aircraft3. SAFETY:The use of oxygen and oxygen systems involves a certain degree of hazard. With the proper design, installation, and maintenance, this hazard can be reduced to an acceptable level.Oxygen in gaseous or liquid form is chemically

    9、 stable and nonflammable. However, combustible materials ignite more rapidly and the intensity of a fire increases tremendously in an oxygen-rich atmosphere.A major factor in oxygen systems is cleanliness. This is most important in fabrication, installation, and maintenance of equipment. From the in

    10、stallation standpoint, the hazards of contamination should be minimized, if not completely eliminated, by choosing proper locations for the equipment and by adequate precautions and shielding where choice of location is limited.4. INSTALLATION:Care should be taken in the installation of the oxygen s

    11、ystem. Protect all lines and fittings from any unnecessary abuse or scratches during installation. Low pressure aluminum alloy plumbing lines are likely to become damaged; therefore, installation and location should be so accomplished as to prevent oxygen equipment or plumbing from subjection to vib

    12、ration, abrasion, or damage during other maintenance operations. All oxygen system lines, after installation, should be carefully inspected for damage and leakage. Leak testing can be accomplished by introducing the oxygen pressure into the system and examining connections by the use of a leak detec

    13、tion solution specifically approved for oxygen service. Before any oxygen system component is removed or any connection is loosened, oxygen system pressure should first be dissipated.5. EQUIPMENT HANDLING:All oxygen equipment should be handled with care to avoid association with hydrocarbons such as

    14、 fuels and lubricants which are ever present where aircraft are serviced and/or maintained. Because most oxygen components are of an intricate nature and all require cleanliness for proper operation, they should be kept in their original containers or be provided with a proper protective covering un

    15、til ready for installation in the aircraft. This is also necessary when any of the items from an aircraft are removed for service and/or overhaul. Keep protective caps in position on equipment as long as possible and replace as soon as possible. Do not tamper with safety device or mar identifying ma

    16、rkings or symbols and/or nameplates.SAE INTERNATIONAL AIR1392A Page 2 of 6_6. MODIFICATION INSTALLATION:When oxygen equipment is modified and/or replaced with new or different equipment, the following should be taken into consideration prior to making the actual installation:The oxygen equipment, tu

    17、bing, and fittings shall be located as remotely as practicable from fuel, oil, hydraulic fluid, storage batteries, exhaust sacks and manifolds, electrical radios, and insulating materials. Insofar as practical, oxygen lines should not be grouped with lines carrying flammable fluids. Where necessary,

    18、 deflector plates should be used to keep flammable fluids away from oxygen lines and equipment. Components of any oxygen system should not be installed where they will be subjected to temperatures in excess of that specified in the individual component specifications, and no part of the system shall

    19、 be installed in an area which will be subjected to a temperature of 180 F (82 C) or greater.7. CLEARANCE REQUIREMENTS:Wherever possible oxygen lines, fittings, and equipment shall be installed above and at least 6 inches (152.4 mm) away from fuel, oil, and hydraulic systems to avoid contamination.

    20、Deflector plates should be used where necessary to keep hydraulic fluid away from oxygen lines, fittings, and equipment. Open ends of cleaned and died tubing should be plugged with impermeable caps at all times except during attachment or detachment. There should be at least 2 inches (50.8 mm) of cl

    21、earance between the oxygen system and flexible moving parts of the aircraft. There should be at least half-inch clearance between the oxygen system and rigid parts of the aircraft. The oxygen system tubings, fitting and equipment should be separated by at least 6 inches (152.4 mm) from all electrica

    22、l wiring, heat conduits and heat emitting equipment in the aircraft. Insulation shall be provided on the hot ducts, conduits, or equipment to prevent overheating of the oxygen system.8. TORQUENING OF JOINTS:Tightening of flared tube and pipe connections shall be accomplished in accordance with the b

    23、est commercial practice. Torque wrenches shall be used, and the torque applied shall be within the limits specified in Tables 1 and 2.SAE INTERNATIONAL AIR1392A Page 3 of 6_9. OXYGEN SYSTEM AND COMPONENT CLEANING:9.1 Oxygen system components, including supply plumbing, can most effectively be cleane

    24、d when not installed in the system. Components containing plastic or elastomeric parts are subject to damage when exposed to some cleaning agents and they result in odors which are difficult to remove satisfactorily. Contaminants, such as oil, dust, metal chips, etc., cannot be easily removed by gas

    25、 purging or liquid flushing within the installed system. Such contaminants can eventually become trapped in some narrow orifices causing either partial or complete failure of the system. In addition, if the contaminant is of the combustible type, a fire hazard is possible. Such contaminants can only

    26、 be removed by complete disassembly of the affected component followed by proper cleaning procedures and controlled handling of the clean component until reinstalled into the using system.9.2 Cleaning materials and processes used shall be compatible with the pieces being cleaned. Solutions and solve

    27、nts used for cleaning and gases used for drying shall be of sufficient purity to prevent accumulation of undesirable residue after drying.TABLE 1 - Torque Requirements for Flared Tube ConnectionsTubing O.D.Inch (mm)MinimumTorqueInch-Pounds (Nm)MaximumTorqueInch-Pounds (Nm)5/16 (8) 100 (135.6) 125 (1

    28、69.5)3/8 (10) 200 (271.2) 250 (339.0)1/2 (13) 300 (406.8) 400 (542.3)TABLE 2 - Torque Requirements for Pipe Connections1Nominal PipeSizeInch (mm)MinimumTorqueInch-Pounds (Nm)MaximumTorqueInch-Pounds (Nm)1/8 (3) 40 (54.2) 150 (203.4)1/4 (6) 60 (81.4) 200 (271.2)3/8 (10) 100 (135.6) 400 (542.3)1Torque

    29、 to specified minimum value and check for leakage. Ifadditional torque is required to stop leakage, torque may beapplied up to specified maximum value.SAE INTERNATIONAL AIR1392A Page 4 of 6_9.3 Cleaning agents must be completely removed from all equipment. The cleaned equipment shall be carefully ex

    30、amined for any trace of cleaning agents. After solvent cleaning, check for solvent residues using a Halogen Detector. After cleaning with a water-soluble cleaning agent, visually inspect the equipment for complete moisture removal. If components that have been previously cleaned are not to be used i

    31、mmediately they should be wrapped and/or sealed in a polyethylene bag and to the exterior of the bag should be placed the following: “Cleaned for Oxygen Use” and date.10. TRANSFILLING OF OXYGEN CYLINDERS:10.1 Filling or recharging of oxygen cylinders may be accomplished by removal of the cylinder fr

    32、om the aircraft or by the use of central point filler valves normally accessible from outside the aircraft. Either method is acceptable. The central point filling minimizes a major difficulty in cylinder removal which is maintaining the mandatory cleanliness of the system. In cylinder removal, one o

    33、r more lines must be disconnected, and the cylinder and/or systems are subjected to the possibility of contamination. Before any oxygen cylinder filling the following precautions must be taken: Each cylinder should be inspected for conformance to latest DOT regulations. Oxygen cylinders that conform

    34、 to the DOT regulations are marked to indicate specification number and the “service pressure” for which the cylinders are designed. This marking is normally located immediately below the neck ring and consists of a combination of numbers and letters. For example, the designation DOT 3A1800 (12.4 MP

    35、a) indicates that the cylinder was fabricated and tested in accordance with DOT specification 3A for a service pressure of 1800 psig (12.4 MPa). Additional marks normally located beneath this marking include an identifying number of the cylinder owners and a series number. In addition, the date of o

    36、riginal manufacture and a symbol identifying the manufacturer are also located on the shoulder of the cylinder. In accordance with specific DOT regulations, certain cylinders must be retested before recharging as follows: Specification 3A and 3AA cylinders must be retested every 5 years; Specificati

    37、on 3HT cylinders must be retested every 3 years. In the case of 3HT cylinders, after 4380 refills or 15 years (whichever comes first), the cylinder must be scrapped. All cylinders that do not conform to the above requirements should not be filled. Nonconforming cylinders may be forwarded to a cylind

    38、er manufacturer or DOT/FAA authorized reconditioning facility.10.2 If non-standard ambient temperatures should prevail at the time of filling, refer to Table 3 to determine the proper filling pressure for oxygen cylinders. Table 3 should be used as a guide and has been found to be sufficiently accur

    39、ate.SAE INTERNATIONAL AIR1392A Page 5 of 6_PREPARED BY SAE COMMITTEE A-10, AIRCRAFT OXYGEN EQUIPMENTTABLE 3At TemperatureF (C)Fill to Working Pressurex Figure BelowAt TemperatureF (C)Fill to Working Pressurex Figure Below110 (43.3) 1.10 70 (21.1) 1.000105 (40.6) 1.0875 65 (18.3) 0.9875100 (37.8) 1.075 60 (15.6) 0.97595 (35.0) 1.0625 55 (12.8) 0.962590 (32.2) 1.05 50 (10.0) 0.9585 (29.4) 1.0375 45 (7.2) 0.937580 (26.7) 1.025 40 (4.4) 0.92575 (23.9) 1.0125SAE INTERNATIONAL AIR1392A Page 6 of 6_


    注意事项

    本文(SAE AIR 1392A-1998 Oxygen System Maintenance Guide《氧气系统维护指南》.pdf)为本站会员(sofeeling205)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开