1、T; 9 MIL-STD-LbL3B 84 m 77777LL 0087634 7 PNCH-POUND 1 MIL-STD-1613B 1 March 1990 SUPERSEDING 25 June 1980 MIL-STD-1613A MILITARY STANDARD PROVISIONS FOR EVALUATING QUALITY OF GLOVES, LEATHER, DRESS FSC 84GP AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. P
2、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- I - MIL-STD-LbL3B 84 77977LL 0087635 7 MIL-STD-1613B FORWARD 1. This Military Standard is approved for use by all Departments and Agencies of the Department of Defense. 2, Beneficial comments (recomme
3、ndations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Pro
4、posal (DD Form 1426) appearing at the end of this document or by letter. 3. This document supplements the military specifications listed below. It provides a standard description for defects and standardizes examination requirements. Specification Title PD-274 MIL-G-24909 1 Y Gloves, Leather, Dress,
5、 Lined and Unlined Gloves, Mens and Womens (U.S.M.A.) ii Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-e Paragraph MIL-STD-LbL3B 84 77777LL 008763b O MIL-STD-1613B CONTENTS Page 1. SCOPE 1.1 Scope 1.2 Application 2. APPLICABLE DOCUMENTS 2.1 Governm
6、ent documents 2.1.1 Specifications, standards, and handbooks 2.2 Order of precedence 3. DEFINITIONS 3.1 Fabric defects 3.2 3.3 Open seam z Quality assurance terms and procedures more than 1/2 inch (longest dimension in any direction) 1 size of the normal diameter of the yarn 1 11, Color not as speci
7、fied 2 c. Knot, slubby yarn more than twice the diameter / 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-36338 BLt 7377733 0089b39 b W MIL-STD-1613B Table I - Classification of defects (contd) Point Value III. Thread for fingers and thumb
8、 closure (when applicable): a. Omitted 2 b. Color other than specified, or mismatched for shade with the liner 1 IV. Construction and Assembly a. Not as specified 2 b. When applicable, fingers and thumb open or insecurely closed 2 C. Bulky, twisted, or poorly formed 2 5.2 End item examination. The g
9、loves shall be examined and all defects shall be penalized as indicated in Table IV of this standard. The sample size shall be based on lot size and the acceptance value for 3 and 2 point defects and total (3, 2, and 1 point) defects shall be as specified in Table III. The sample unit shall be one g
10、love and the selection shall be by pairs. Defects or pairing shall be classified as a single defect. The lot shall be unacceptable if: The point value of 3 and 2 point defects exceeds the applicable OR The point value for total (3, 2, and 1 point) defects exceeds the a. maximum acceptable point valu
11、e. applicable maximum acceptable point value, b. 5.3 Dimensional examination. The appropriate number of gloves selected in pairs, and as determined from the table below, shall be examined for . conformance to the dimensional requirements cited in the table of measurements of the appropriate glove sp
12、ecification. When a measurement deviates from a dimension and tolerance specified, -the glove shall be penalized one point. The lot shall be unacceptable if the total point value exceeds the maximum acceptable point value specified below. Each size glove present in the lot shall be represented in th
13、e sample selected for this examination. Lot size Sample size Maximum Acceptable Point Values Up thru 500 8 501 thru 3200 13 3201 thru 35,000 20 35,001 and up 32 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-IILB 4 77979LL OOSbYO 2 H MIL-S
14、TD-1613B 5.4 Examination of packaging requirements. An examination shall be made to determine that packaging, packing, and marking comply with Section 5 requirements of the appropriate glove specification. Defects listed below shall be scored one point. The sample iinit shall be one shipping contain
15、er fully prepared for delivery. Defects of closure listed below shall be examined on shipping containers fully prepared for delivery. The lot shall be unacceptable if one or more points are scored for this examination. Examine Defect Marking (exterior Omitted, incorrect, illegible, of improper size,
16、 and interior) location, sequence, or method of application, Materials Any component missing, damaged, or not as specified. I Workmanship Content Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, inadequate stapling, bulged or dis
17、torted container. Number of items per shipping container is more or Size shown on one or more items not as specified on less than required. shipping container. - 1/ - 1/ For this defect, one item from each shipping container in sample shall be examined. 5.5 Inspection procedures. Inspection shall be
18、 as specified in MIL-STD-105, except where otherwise indicated in this document. 5.6 Initiation of inspection. Normal inspection will be used at the start of inspection unless otherwise directed by the procurement quality assurance element administering the contract. 5.7 Continuation of inspection.
19、Normal, tightened, or reduced inspection shall continue unchanged on successive lots except where switching procedures in 5.8 require change. 5.8 Switching procedures. 5.8.1 Normal to tightened. When normal inspection is in effect, tighte inspection shall be instituted when two out of five consecuti
20、ve lots have been rejected on original inspection, (i.e., ignoring resubmitted lots for this procedure). 5.8.2 Tightened to normal. When tightened inspection is in effect, normal inspection shall be reinstituted when five consecutive lots have been considered acceptable on original inspection. ,/ 4
21、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I l l l I I l I I l I t I I I I I l l l I MIL-STD-LbL3B L( W 7777733 0087bVL 9 W MIL-STD-1613B 5.8.3 Normal to reduced. When normal inspection is in effect, reduced all of the following conditions inspe
22、ction shall be instituted providing that are satisfied: a. The proceeding 10 lots have been on normal inspection and none have been rejected on original inspection; and b. The total number of points for 3 and 2 point defects in the samples from the preceeding 10 lots is equal to or less than sixty p
23、ercent of the total maximum acceptable point values for 3 and 2 point defects from the preceeding 10 lots; and r C. The total number of points for 3, 2, and 1 point defects in the sample from the preceeding 10 lots is equal to or less than seventy-five percent of the total maximum acceptable point v
24、alues for 3, 2, and 1 point defects from t: the preceeding 10 lots; and d. Production is at a steady rate; and e. Reduced inspection is considered desireable by the procurement quality assurance element administering the contract. 5.8.4 Reduced to normal. When reduced inspection is in effect, normal
25、 inspection shall be instituted if any of the following occur on original inspection: a. A lot is rejected; or b. A lot is considered acceptable but exceeds the applicable first value 0 (see - 1/ to Tables II and III); or c. Production becomes irregular or delayed; or d. Other conditions warrant tha
26、t normal inspection be reinstituted. 5 t Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-LbL3B L( m 49779LL 007b112 b m MIL-STD-1613B Table II - Sampling Provisions for Preassembled Knit Liner Maximum acceptable point values Sample 3&2 point
27、3,2,&1 point Lot size size defects defects Normal Up thru 50 5 2 points 4 points Inspection 51 thru 150 8 3 points 5 points 151 thru 280 13 4 points 6 points 281 thru 500 20 5 points 7 points 501 thru 1200 32 6 points 9 points 1201 thru 3200 50 9 points 13 points 3201 thru 10,000 80 14 points 19 poi
28、nts 10,001 thru 39,000 125 19 points 26 points 39,001 and over 200 27 points 38 points Tightened Up thru 50 Inspection 51 thru 150 151 thru 280 281 thru 500 501 thru 1200 1201 thru 3200 3201 thru 10,000 10,001 thru 39,000 39,001 and over Reduced Up thru 280 Inspection 281 thru 500 501 thru 1200 1201
29、 thru 3200 3201 thru 10,000 10,002 thru 39,000 39,001 and over 5 8 13 20 32 50 80 125 200 5 8 13 20 32 50 80 2 points 2 points 3 points 4 points 5 points 6 points 9 points 14 points 22 points 3&2 point defects - 1/ 2-3 points 2-5 points 3-8 points 4-11 points 6-14 points 9-17 points 14-22 points 3 p
30、oints 4 points 5 points 6 points 7 points 9 points 13 points 21 points 32 points 5 points 7 points 10 points 14 points 18 points 22 points 27 points 3 1/ If the first value is exceeded but the second value has not been exceeded, accept the lot but reinstate normal inspection (see 5.8.4b). The second
31、 value is the maximum acceptable point value. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 l l l li I 1% I l I I I I I I MIL-STD-3bL3B 4 m 7977733 0089643 m MIL-STB-1613B Table III - Sampling Provisions or Leather Dress Gloves : Si3Hlple 3&2 p
32、oint 3,2,&1 point Lot size size defects defects Normal Up thru SO Inspection 51 thru 150 151 thru 280 281 thru TOO 501 thru 1200 1201 thru 3200 3201 thru 10,000 10,001 thru 39,000 39,002. and over Tightened up thru 50 Inspection 51 thru 150 151 thru 280 281 thru 500 501 thru 1200 1201 thru 3200 3201
33、 thru 10,000 10,001 thru 39,000 39,001 and over Reduced Up thru 280 Inspection 281 thru 500 501 thru 1200 1201 thru 3200 3201 thru 10,000 10,001 thru 39,000 39,001 and over a3 20 32 50. 80 125 200 sa5 500 13 20 32 50 80 125 200 315 500 13 20 32 %O 80 125 200 3 points 5 points 7 points 9 points 14 po
34、ints 19 points 27 points 38 points 59 points 2 points 3 points 5 points 7 points 9 points 14 points 22 points 33 points 49 *points 3&2 point defects - 1/ 2-8 points 3-11 points 6-14 points 8-17 points 2.4-22 points 19-27 points 27-35 points 5 points 7 points 10 points 13 points 19 points 26 points 3
35、8 points 54 points 80 points 4 points 6 points 8 points 10 points 14 points 21 points 32 points 48 points 72 points 10 points 13 points 17 points 21 points 27 points 34 points 46 points - I/ If the first value is exceeded but the second value has not been exceeded, accept the lot but reinstate norma
36、l inspection (see 5.8.4b). value is the maximum asceptable point value. The second Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_ - - MIL-STD-LbL3B 4 77777LL 0087b44 T MIL-STD-1613B *6. NOTES (This section contains information of a general or exp
37、lanatory nature which may be helpful, but is not mandatory.) *6.1 Intended use. This standard contains requirements for evaluating quality of leather dress gloves. *6.2 Issue of DODISS. When this standard is used in acquisition, the issue of the DODISS to be applicable to this solicitation must be c
38、ited in the solicitation (see 2.1.1). *6.3 Changes from previous issue. The margins of this standard are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only and the Government assu
39、mes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. *6.4 b Subject term (key word) list
40、ing. Handwear, Defects of Handwear, Inspection of 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1613B 4 m 3999911 0087645 1 m MIL-STD-1613B I 1 1 l 1 i i Table IV - Classification of Defects *The defect shall be classified as 3 -points wh
41、en it seriously affects .the serviceability or appearance and 1 point when affecting service- ability or appearance, but not seriously. II. Shaded Parts Point Value I. Leather Defects and Damages a, b* C. d. e. f. g* h. i. j. k. 1, m. Any hole (except pinhole or needle hole), tear, thin or weak area
42、 (including evidence or slaughter cut) Not full grain Not soft and pliable Grain damage(s) or imperfection(s), e.g., grub or tick marks, cockle, scratch, scar, abrasions and blocking Wrinkles Brittle or bony area Flesh side of leather not smooth or contains loose flesh in excess of one square inch i
43、n total area Loose, spongy, or flanky Excessive stretch in length direction of glove Three or more pinholes throughout glove Three or more exposed needle holes Spot or stain, discoloration, e.g., bloom, blushing, Loose flesh protruding from seam (i.e., not cut clean) bronzing, spue 3 3 3 * * * 2 * 3
44、 1 1 2 1 a. On outside: -Any part shaded or variation in shade within a glove 2 b. On inside: -Any liner part badly shaded within a glove i 9 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-r III. IV I V. Cleanness MIL-STD-LbL3B 84 LL 008b4b 3 MIL-
45、STD-1613B Table IV - Classification of Defects (contd) Point Value a. b. Thread ends - on outside: Spot or stain on liner or lining 1. More than one but not more than 1 hree not trimmed to less than 1/2 inch 1 2 2. More than three not trimmed to lss than 1/2 inch C. Two or more shade or size tickets
46、 not remved 1 d. of the knitted liner 1 Any evidence of the gum paste visible on the surface e. Any evidence of gum paste or adhesive on leather 1 Cutting -Any component part not cut in accordance with specified pattern or not in accordance with specification requirements 3 Components and Assembly a
47、. Any component part or operation omitted (unless otherwise classified herein) 3 b. Any component not as specified 3. cb Any component part tight, twisted, distorted, pleated, or full (unless otherwise classified herein) 2 . d. Any operation not as specified (unless otherwise classified herein) 2 i
48、10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-r) - i MIL-STD-Lb13B 4 7494711 0084647 5 E.11 L- SEL l. 6 i 3B Tabla IV - Classification of Defects (contd) VI. Seams and Stitching Point Value a. Accuracy of seaming: 1, Seam puckered 1 2. Seam irre
49、gular, pleated or wavy 2 3, Any part of glove caught in unrelated operation 2 4, when not caught in other seams or stitching, backtacked less than $14 inch 1 when not caught in other seams OF stitching, not having chain extending beyond eaeh end when not caught in other seams or stitching, having chain extending less than 1/2
