1、MIL-STD-3386 -62 83 m 7777733 0072833 T m _. . .* MILITARY STANDARD LOADING OF HAZARDOUS MATERIALS AND ASSOCIATED ITEMS IN MILVAN CONTAINERS PARAPAC ASSEMBLY MK 36 MOD O FOR UNDERWATER MINE MK 55 FLEET ISSUE UNIT LOAD UNIT LOAD DATA UNIT LOAD DRAWING . WR-54238 DIMENSIONS . 48 L X 48 W X 38 3/4 H WE
2、IGHT fAPPROXI 830 LBS CUBE . 51.6CU FT DOT HAZARD CLASSIFICATION . INERT COAST GUARD CLASS . &- 3Y- 03 MIL-STD-1386-62 (NAVY) 30 SEPTEMBER 1975 . NONE INDEX NOTES: I, 2. UNLESS OTHEKWSE SPECIFIED DIMENSIONS ARE IN IhCHES. FOR CROSS REFERENCETO ASSOCIATED PALLETIZING, TRUCK- LOADING AND CARLOADING MI
3、LITARY STANDARDS. REFERTO ITEM PAGE - GENERAL NOTES TOFC/COFC, CONTAINER- SHIP & HIGHVfAY 2 2L3 DETAILS 2 THEINDEX TO STANDARDS MIL-HDBK-236 (NAVY). . I FSC 8140 II AUTHORIZED FOR TRAILER-ON- FLAT-CAR (TOFC), CONTAINER-ON- FLAT-CAR (COFC), CONTAINERSHIP h AND HIGHWAY SHIPMENTS -i Provided by IHSNot
4、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-2386 -62 BI m 7777921 0072814 I m MIL-STD-1386-62 (NAVY) GENERAL NOTES I. THIS DOCUMENT GIVES DETAILED INSTRUCTIONS FOR LOADING THE MILVAN CONTAINER WITH FLEET ISSUEUNIT LOADS OF THE PARAPAC ASSEhrBLY MK 36 MOD O
5、FOR UNDERWATER MINE MK 55. THE UNIT LOADS SHALL BE PALLETIZED IN ACCORDANCE WITH WR-Y/238. THEMILVAN SHALL BE EQVIPPED WITH A MKHANICAL LOAD-BRACING SYSTEM THAT MEETS EHE REQUIREMEMS OF THE BUREAU OF EXPLOSIVES PAMPHLET K. IN ADDITION TO THE BEL1 RAILS REQUIRED BY PAMPHLET K, THE MILVANCONTAINER HAS
6、 BEL1 RAILSAT THE 72AND 83 INCH HEIGHTS FROM THECONTAINER FLOOR. CONTAINERS ARE ECXIIPPED WITH 25 CROSSMEMBERS. UNUSED CROSSMEMBERS MUST REMAIN WITH THECONTAINER AND SHALL BE FASTENED INTO THE BELT RAILS FOR SHIPMENT, 2. 3. 4 pK1 WHEN POSITIONING CROSSMEMBERS MAKE A VISUAL CHECK TO ENSURE THAT THE C
7、ROSSMEMBERS ARE LOCKED SKURELY IN PLACE. 5. WHEN THE LONGITUDINAL SLACK BETWEEN A CROSSMEMBER AND THE UNIT LOAD IS GREATER THAN ONE INCH, USE FILL MATERIAL TO SHIM BETWEEN THECROSSMEMBER AND THEUNIT LOAD, AS SHOWN IN DETAIL B. LENGTH OF STRUT, PIECE 1, SHALL BE SUFFICIENT IO CAUSE SWAY BRACE, DETAIL
8、 A, TO FILL VOID BETWEEN THE UNIT LOAD AND THE CONTAINER SIDhVALL. TWIST-TIE BOTH ENDS OF ASSEMBLYTO CROSSMEMBER WITH 16 GAUGE SOFT ANNEALED WIRE, 4 PLACES. 6. 7. APPLICABLE MATERIAL SPECIFICATIONS: DUNNAGE LUMBER - FED. SPEC. MM-L-751 NAILS - FED SPEC. FF-N-105, TYPE II, STYLE IO, COMMON BRIGHT. E
9、AFTERBLOCKING AND BRACING HAS BEEN INSPECTED, ATTACH SHIPPING DOCUMENTS INSIDE THECONTAINER IN AN ACCESSIBLE AREA, CLOSEAND SEAL THECONTAINER DOORS. TOFC/COFC,CONTAI NERSHIP AND HIGH WAY I. 2. THE CONTAINER LOAD CONSISIS OF 8 UNIT LOADS WHICH MUS1 BE LOADED AND DUNNAGED IN ACCORDANCE WITH THIS DOCUM
10、ENT. THE LOADED CONTAINER MAY BE TRANSPORTED OVER PUBLIC HIGHWAYS ON THEMILVAN CHASSIS USING THE FOLLOWING CONFIGURATIONS: o. b. ONECONTAINER ON A 20 FT MILVAN CHASSIS WITH DOUBLE BOGGIES AND PULLED BY A DOUBLEDRIVE AXLE TRAILER. TWO CONTAINEIIS ON A 40 FT MILVAN CHASSIS WITH DOUBLE BOGGIES LOCATED
11、IN THE REARMOST POSITION AND PULLED EYA DOUBLE DRIVE AXLE TRACTOR. 3, ONEORT:/O LOADED CONTAINERSMAY ALSO BE IRANSPORTED OVER PUBLIC HIGHWAY ON SUITABLE COMMERCIAL EGJIPMENlOF APPROPRIATECAPACITY THAT MEETS THE REOUIREMENTS OF THE CODEOF FEDERAL REGULATIONS. 4. THE LOADED CONTAINERS MAY BE SHIPPED T
12、OFC COK. WHEN SHIPPING TOFC THE FOLLOWING CONFIGURATIONS ARE AUTHORIZED: o. b. ONE CONTAINER ON A 20 FT MILVANCHASSIS ECXIIPPED WITH DOUBLEBOGGIES. TViO CONTAINERS ON A 40 FT MILVAN CHASSIS EGUIPPED WITH DOUBLE BOGGIES. (WARNINGI CHASSIS CONTAINERS COUPLED INTO A 40 FI TRAILER CONFIGURATION MUST BE
13、PLACED AT THE B-END OF THE TOK CAR. THE REAR END OF THE 40 FT UNIT WILL OVERHANG THE END OF THECAR IF IT IS PLACED AT HEA-END. 20 FT AND 40 FT UNITS CAN BE LOADED ON THE SAME CAR. PAGE 2 _,- DETAIL e SWAY-BRACE 8 REQUIRED PILL MIERIAL 1 x 4 OR 2 x 4 - 16 GA TIE WIRE ONE LOOP, TWIST TIED DETAIL FILL
14、MATERIAL SE? GENERAL NOTE 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-13b -62 L = 77777LL 0072815 3 SEE DETAIL MIL-STD-1386-62 (NAVY) SECTION C-C CONTAINER LOAD DATA NUMBER OF UNIT LOADS . 8 NUMBER OF CROSSMEMBERS REQD . 20 LOAD WEIGHT
15、(APPROX) 6,640 LBS DUNNAGE WEIGHT (APPROX) . 365 LBS CONTAINER WEIGHT . 5,785 LBS GROSS WEIGHT (APPROX) 12,790 LBS / 2 HORIZOMAL 2 x 6 x 54 1/2 16 1 JIJOINT IM I I I 2x 6 x TO SUIT 24 SEE 2 I STRUT I- NO.KS NAIL I *IZE SIZE REQD TO NAILS IECE NO. DESCRIPTION I UST OF WTERIALS AND NAIUNG DATA TOFC/COFC, CONTAINERSHIP AND HIGHWAY PREPARING ACTIVLTY: IPROJKT NO. 8140-N-297) REVIEW ACTIVITY: NAW -0s NAVY -OS PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
