1、- MIL-STD-1323 -LY7A AL m 7777713 0071Y27 LI m S -37-03- MILITARY STANDARD MIL-STD-1323-149 A (NAVY) 7 JUNE 19S9 UNIT LOAD, FOR .UNDERWAY RE PL ENI SHM E NT Superseding XIL-STE-1323-149 22 October 1982 16 INCH 50 CAL. H.C./H.E. PROJECTILE MK 13 AND MK 19 IN PALLET ADAPTER MK 88 MOD O _UNIT LOAD DATA
2、, GROSS WEIGHT OF ONE PROJECTILE ._. IWO LBS. WEIGHT OF ADAPTERS (ESTIMATED) 235 LES. NUMBER OF PROJECTILES PER UNIT LOAD 2 KAZAW CLASSIFICATIOX DODIC/NALC 1 E I D875/D877 CL. A CL. VI1 D874/D878/ CL. A CL. v WEIGHT OF PALLET . 94 LES. Ds?s/Dsso- I . WEIGHT OF STRAPPING AND DUNNAGE 25 LBS. D882 I I
3、GROSS WEIGHT OF UNIT LOAD (ESTIMATED) . 4155 L6S.n DO NOT USE FOR SHIPPING WEIGHT DO NOT STACK MORE THAN 6 UNIT LOADS HIGH IN STORAGE PROJECTILE DWG. 328339 AMCC NO. - N/A A Id7 Added Hazar Classifications, REV LTR REVISION DESCRIPTION DATE I I DISTRIBUTION STATEMENT A APPROVED FOR PUBLIC RELEASE: I
4、. 2. UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. FOR CROSS REFERENCE TO ASSOCIATED TRUCKLOADING, CONTAINERL OADING AND CARLOADING MILITARY STANDARDS, REFER TO INDEX TO STANDARDS, M IL-HDBK-236 INAVYI. THIS UNIT LOAD IS AUTHORIZED AND RELEASED FOR SHIPPING, HANDLING, STORAGE AND TRANSFER-AT
5、-SEA. DOMESJIC SHIPMENT IN COMPLIANCE WITH DOT REGULATIONS. IT MAY ALSO BE USE0 FOR REQUIREMENTS FOR CONSTRUCTION OF THIS UNIT LOAD SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF MIL-STD-1323 (NAVY), ?&i ic/a.b/?L DATE ORIGINATOR WPNSTA EARLE, NEW JERSEY 1- V Licensed by Information Handling
6、 ServicesMIL-STD-1323 -147A 81 7979711 007L430 O U B M IL-STD-13 2 3 -1 49 NAVY) PALLETIZING PROCEDURE (a) THREAD STRAPPING, ITEM 2, BETWEEN 5TH AND 6TH DECK WIRES OF PALLET, ITEM 1, AS SHOVfi IN DETAIL A. (b) POSITION BASE END OF THE BOTTOM FRAHE , ITEM 6, 1“ BEHIND THE EID OF PALLET WITH EQUAL OVE
7、RHANG ON BOTH SIDES, ALIGN THE PROJECTILES ON CRADLE. (C) POSITION THE END CAP AFT AND END CAP FHD, ITEN 7 AND 8, ON THE BOTTOM FRAME. d) POSITION STRAPPING, ITEM 3, UNDER PALLET DECK AROUND THE BOTTON FRAME AND CRADLE AND OVER THE PROJECTILES, TENSION AND DOUBLE NOTCH SEAL ITEM 5. (e) PLACE 2 X 8 V
8、ERTICAL STRUTS, ITEM 10, AS SHOWN BELOW AND IN DETAIL B WITH CHAMFER AGAINST LOWER ANGLE FILLET AND STRUTS BUTT AGAINST FWD EDGE OF ANGLE. (f) PLACE TOP FRAME, ITEM 9, OVER VERTICAL STRUTS AND UNIT MAD AS SHOWN. (4) POSITION STRAPPING, ITEI 4, UNDER PALLET DECK OR EiOTTOtl FRAME AND AROUND UNIT LOAD
9、. LOCATE STRAPPING ON STRUT AS SHOWN IN DETAIL BI DRIVE IN STAPLES, ITEM 11 HALFWAY, TENSION AND DOUBLE NOTCH SEAL, THEN DRIVE IN STAPLES TO SECURE STRAPPING IN POSITION. Ih) POSITIOI STRAPPING, ITEM 2, AROUND THE UNIT LOAD, TENSION AND DOUBLE NOTCH SEAL. MARKING: IN ADDITION TO ANY SPECIAL MARKING
10、REQUIRED BY CONTRACT OR ORDER, UNIT LOAD SHALL BE MARKED IN . * THIS DIMENSION IS DETERMINED BY ACCORDANCE WITH MIL-STD-1323. STRAPPING LOCATION SHOWN IN Y I WARNING LATERAL STRAPS MUST NOT BE PLACED OVER DECK WIRES SHOWN OR STRAPS MAY FAIL. PAGE 2 DEPALLETIZING PROCEDURE (o1 CUT AND REMOVE STRAPPIN
11、G, ITEMS 2 & 4 b) (c) (dl REMOVE PROJECTILES, REMOVE TOP FRAME AND END CAPS, AND VERTICAL STRUTS. CUT AND REMOVE STRAPPING, ITEM 3. (e) REMDVE BOTTOM FRAME. Licensed by Information Handling ServicesMIL-STD-1323 -147A 83 W 7777731 0071431 2 H * - I a a .U DETAIL 0 (BOTTOM FRAME RIM OMITTED FOR CLARIT
12、Y) NOTE: STRAPPING DIMENSION IS SELECTED SO THAT WHEN STRUT IS INSTALLED STRAPPING CAN BE SATISFACTORILY PASSED UNDER PALLET DECK WITHOUT INTERFERENCE WITH DECK WIRES. SEE WARNING ON PG. 2. MIL-STD-1323-149 A (NAVY) fl 3/8“ CHAMFER (2 PLACES) /4 STAPLES (2 PERSIDE) I-V4 INCHES, 2“ PREFERRED VERTICAL
13、 STRUT 2 x 8 x20 1/2 / 2 REQD “. 3/6“CHAMFER (2 PLACES) UNLESS OTHERWISE SPECIFIED, ALL MATERIALS WILL BE IN ACCORDANCE WITH MIL-STD-1323. FOR 2“ STRAP FOR 1 1/4 “ STRAI MAY BE USED 4 II STAPLES COML PREFERRED i REVIEW ACTIVITY: NAW-OS PREPARING ACTIVITY: NAVY-OS (PROJECT NO. C140-N&31 PAGE 3 $?US. GOVERNMENT PRINTING OFFICE 19119: - 604-033/13115 ciil Licensed by Information Handling Services
