1、MILITARY STANDARD M IL-STD-1320-8 3 (NAVY) 2 NOVEMBER 1979 SLTfRjFDING TRUCKLOADING GUIDED MISSILE, AIM-9G OR 9H IN CRADLE, MK 16 MOD 0 OR AIM-9G, 9H OR 9L IN CONTAINER, CNU-287/E WR-51/83 30 APRIL 1970 W/O WINGS AND FINS (SIDEWINDER) UNIT LOAD UNDERWAY REPLENISHMENT UNIT LOAD DATA LENGTH . 136 WIDT
2、H . 36 3/8 HEIGHT 34 WEIGHT SEE TABLEI CUBE 97.3 CU. FT. DOT HAZARD CLASSIFICATION EXPLOSIVES A UNIT I FT. LOAD DRAWING MIL-STD-1323-169 INDEX - ITEM GENERAL NOTES FTL 40 FT FLATBED LTL 40 FT FLATBED UNITIZING PROCEDURE DETAIL .OAD NOTES: 1, 2. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES. FO
3、R CROSS REFERENCE TO ASSOCIATED PALLETIZING, PAGE 2 3 4,5&4 8 69 9 I FSC 814C CONTAINERLOADING AND CARLOADING MILITARY STANDARDS, REFER TO INDEX TO STANDARDS, MIL-HDBK-236 (NAVY) II AUTHORIZED AND RELEASED FOR HIGHWAY SHIPMENTS ONLY . . . . . .: 49 Provided by IHSNot for ResaleNo reproduction or net
4、working permitted without license from IHS-,-,-MIL-STD-1320 -83 81 7777711 0070237 b I MIL-STD-1320-83 (NAVY) GENERAL NOTES I. THIS DOCUMENT GIVES DETAILED INSTRUCTIONS FOR TRUCKLOADING THE SIDEWINDER MISSILE AGM-9G AND AGMdH IN THE MK 16 MOD O CRADLE AND THE AGM-PG, AGM-9H AND AGMdL IN THE CNU-287/
5、E CRADLE. THE CRADLES SHALL BE UNITIZED IN ACCORDANCE WITH MIL-STD-1323-169. PROCEDURES AND PRACTICES DESCRIBED HEREIN ARE INTENDED FOR 40 TO 45 FT. FLATBED TRAILERS. DO NOT USE TRAILERS WITH NON-NAILABLE FLOORS. WHEN LOADING TRAILERS LONGER THAN 40 FT., POSITION LOAD IN CENTER OF TRAILER. CHAINS AN
6、D STEEL STRAPS MAY BE USED INTERCHANGEABLY FOR TIE-DOWNS ON A 1 TO 1 BASIS. STEEL STRAP USED AS TIEDOWNS SHALL BE 2 X .O50 AND SHALL CONFORM TO AND BE APPLIED AS SPECIFIED IN THE GENERAL TRUCKLOADING DOCUMENT MIL-STD-13N (NAVY) AND AS SHOWN ON PAGE 3 OF THIS DOCUMENT. CHAINS, FITTINGS AND LOADBINDER
7、S SHALL MEET THE REQUIREMENTS OF THE GENERAL TRUCKLOADING DOCUMENT MIL-STD-1320 (NAVY) AND APPLIED AS SHOWN ON PAGE 5 OF THIS DOCUMENT. 2. 3. 4. 5. WARNING I THE CHAIN SHALL BEAR AGAINST THE END LIFT TRUCK FITTING (NOT THE LIFTING EYES) TO PREVENT THE CHAIN TOUCHING THE PLASTIC POD. SEE DETAIL F, PA
8、GE 7. 6. PRIOR TO LOADING THE TRAILER AND DURING THE PRELOADING INSPECTION REQUIRED BY NAVWEPS OP 2165 AND REPORTED ON DD FORM 626, THE CHAINS, FITTINGS, AND LOAD BINDERS SHALL BE INSPECTED FORSTRETCH,GOUGING, BENT LINKS, WAR,AND ANY OTHER NOTICEABLE DEFECTS. THE INSPECTOR SHALL CONFIRM THAT THE CHA
9、INS AND LOADBINDERS HAVE BEEN INSPECTED AND SHALL SO NOTE IN ITEM NO. 23 OF DD FORM 626. ANY DEFICIENCY SHALL BE CAUSE FOR REJECTION OFA CHAIN OR LOADBINDER. TWO HIGH UNIT LOADS SHALL BE UNITIZED AS SHOWN ON PAGE 8. EACH STACK OF CRADLES IS SECURED TOGETHERWITH TWO 1 1/4 X .O35 CROSS STRAPS. THESE S
10、TRAPS PASS THROUGH THE FORK POCKETS OF THE TOP CRADLES AND RETURN THROUGH THE FORK POCKETS OF THE CRADLES BENEATH THE TOP CRADLES. THE STRAPS ARE SEALED WITH ON DOUBLE NOTCHED SEAL. EDGE PROTECTORS SHALL BE USED AT EACH FORK POCKET. A SEPARATOR SHALL BE USED BETWEEN CONTAINERS OF THE SAME STACK, SEE
11、 DETAIL A AND C. INSTALL AS SHOWN IN DETAIL F, PAGE 7. THE MAXIMUM GROSS WEIGHT OF THE TRACTOR-TRAILER AND THE ALLOWABLE AXE WIGHTS ARE THE RESPONSIBILITY OF THE CARRIER, THE CARRIER WILL ADVISE THE SHIPPER OF THESE LIMITATIONS AND THE SHIPPER SHALL LOAD THE TRAILER IN SUCH A MANNER THAT THE TRACTOR
12、-TRAILER WILL NOT EXCEED THESE LIMITATIONS. AFTER BLOCKING AND BRACING HAS BEEN INSPECTED, ATTACH “EXPLOSIMS A“ PLACARD TO BOTH SIDES, FRONT, AND BACK OF TRAILER. UNLESS OTHERWISE SPECIFIED, ALL MATERIAL SHALL BE IN ACCORDANCE WITH THE GENERAL TRUCKLOADING DOCUMENT MIL-STD-13N (NAVY). FOR GENERAL TR
13、UCKLOADING PROCEDURES REFER TO THE GENERAL TRUCKLOADING DOCUMENT, MIL-STD-1320 (NAVY). 7. 8. 9. IO. 11. 12. 13. FTL 40 FT TRAILER (FLATBED) SEPARATOR ASSEMBLY 6 REQUIRED PAGE 2 TABLE I WEIGHT LBS. (APPROX) CONTENTS CRADLEG.W.l UNITLOAD I FTL AIM-9G I158 2319 27,828 AIM-9H 1138 2279 27,348 AIM-9L 111
14、5 2233 26.796 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1320 -83 1 7337713 0070238 m MIL-STD-13 20-8 3 (NAVY) UNIT LOAD STRAPS OMITTED FOR CLARITY 2 X 4 DOUBLED. NAIL IST PIECE TO TRAILER FLOOR W/61M NAILS. NAIL 2ND PIECETO 1ST IN LIKE
15、MNNER. 7 SEE DETAIL SECTION 8-8 b TRUCKLOAD DATA NUMBER OF UNIT LOADS 12 NUMBER OF CRADLES 24 WEIGHT. SEE TABLEI 12 12 .050 24 STAKE POCKET PAD (STRAPPING) - I II SEAL FOR 2“ STRAP 48 10 TIEDOWN STRAP 2 X .O50 X 27 FT 6 9 UPRIGHT 2X6X60 6 SEE9 8 CROSS PIECE 2X4X14 12 1 I/ X .035X 6 7 CROSSSTRAP 16 F
16、t 6 EDGE PROTECTOR EE*135-M)-291- 72 I I l I I I 4 1 UNITIZING STRAP I *OS5 I 12 I 3 I SLEEPER IZX4Xm I 24 I SEEFIELD NOTE I I 2 ISEPARATOR 12X 4x76 I 4 I SEE FIELD NOTE I I 1 IBACKUPCLEAT 12X6X24 I 16 I SEEFIELDNOTE I 11 I I NO. PCS. NAIL I IZE J REQD TO NAILS DESCRIPTION SIZE I LIST OF MATERIAL AN
17、D NAILING DATA I FTL-40 FT TRAILER (FLATBED) ?AGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M IL-STD-13 20-83 (NAVY) LTL 40 FT TRAILER (FLATBED) I. WHEN REQUIRED TO SHIP LESS-THAN-TRUCKLOAD, SELECT THE CORRECT LOAD PATTERN FOR THE NUMBER OF C
18、RADLES TO BE SHIPPED FROM TABLE II AND POSITION CRADLES ON TRAILER ACCORDINGLY. WHEN THE CRADLES IN A STACK ARE TWO UNIT LOADS HIGH (FOUR CRADLES HIGH) THEY MUST BE UNITIZED AS SHOWN ON PAGE . WHEN THE CRADLES IN A STACK ARE ONE UNIT LOAD PLUS ONE CRADLE HIGH, THEY SHOULD BE UNITIZED AS SHOWN IN DET
19、AIL G, PAGE 9. WHEN ONE SIDE OF A STACK OF CRADLES IS HIGHER THAN THE OTHER (SEE CENTER STACK OF THE LOAD ON PAGE 3, THE TOP CRADLE ON THE HIGHER SIDE SHALL BE STRAPPED TO THE CRADLE ON WHICH IT RESTS AS SHOWN IN DETAIL H, PAGE 9. SHIPMENTS MY BE MADE ON “DOUBLES WHEN STATE LAW PEWITS. A 28 FT FLATB
20、ED TRAILER MAY BE LOADED WITH TWO STACKS OF CRADLES (8 UNIT LOADS OR 16 CRADLES). LESSER AMOUNTS MY ALSO BE SHIPPED USING THE PRINCIPLES OF THIS DOCUMENT. 2. 3. 4. 5. NO. OF CRADLES - 23 22 21 20 19 18 17 16 PAGE 4 LOAD PATTERN * - FWD NO. OF Cm I5 14 13 12 11 IO 9 8 TABLE II LOAD PATTERN * -f FWD N
21、O. OF CRADLES 7 6 5 4 3 2 1 LOAD PATTERN * 8 LOAD PATTERN SHOWS FLOOR PLAN FOR TRAILER. NUMBER IN SMALL BLOCKS INDICATES NUMBER OF CRADLES IN LAYER. THE TOP CRADLE SHALL HAVE FOUR 1 l/4 X .O35 STEEL STRAPS SECURING IT TO THE CRADLE ON WHICH IT RESTS USING THE PRINCIPLES SHOWN IN DETAIL H, PAGE 9 AND
22、 NOTE 4 ABOVE. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1320 -83 1 W 7777733 O070220 b W MIL-STD-1320-83 (NAVY) UNIT LOAD STRAPS OMITTED FOR CLARITY. SEPARATOR ASSEMBLY SEE GENERAL NOTES 3,4,5&6,PAGE2 4 REQUIRED FROM LEADING EDGE OF TR
23、AILER 2 X 4 DOUBLED. NAIL 1ST PIECE TO TRAILER FLOOR W/5-1M NAILS. NAIL 2ND PIECE TO 1ST IN LIKE MANNER. 2 X 4 DOUBLED. NAIL 1STPIECE TO TRAILER FLOOR VT/l-lM NAIL EVERY 8 INCHES. NAIL 2ND PIECE TO IST IN LIKE MANNER. TRUCKLOAD DATA I. 2 X 6 DOUBLED NAIL 1ST PIECE NAIL 2ND PIECE TO IST IN LIKE MANNE
24、R. u TO TRAILER FL6OR W/6-1M NAILS. NUMBER OF UNIT LOADS . . . . NUMBER OF CRADLES . , , , . 8 1/2 ,17 P 2 SEPARATOR ASSEMBLY 2 REQUIRED 4 1 1/4X .O35 X 12 TIE DOWN STRAP 3 FT I l I i1 UPRIGHT 2X6XM) 2 SEE 9 I I 10 UPRIGHT 2X6X28 4 SEE 9 9 CROSS PIECE 2X4X14 12 10ORi1 3/JOINT Iod 8 CHAIN 6 LOAD BIND
25、ER 3/8 INCH 6 2 7 CROSSSTRAP 16 FT 6 EDGE PROTECTOR FSN 8135-09-291- 32 i 1/4 X .O35 X 0962 2X4X20 2X4X76 SEE FIELD NOTE BACKUP CLEAT 2XX24 16 SEE FIELD NOTE I I I NO. PC. NAIL NUMBER I SEE pl%fl DESCRIPTION SIZE REQD TO NAILS I I I I I LIST OF MTERIAL AND NAILING DATA LTL 40-FT TRAILER (FLATBED) PA
26、GE 5 . . . . .o Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-3320 -3 81 9 7777733 0070223 W M IL-STD-1320-8 3 (NAVY) 4 REQUIRED UNIT LOAD STRAPS SHOWN. SEE GENERAL NOTES 3,4, 5 h6, PAGE 2 2 X 4 DOUBLED. NAIL IST PIECE TO TRAILER FLOOR W/5-
27、1M NAILS. NAILZND PIECE TO IST IN LIKE MANNER. 2 X 6 DOUBLED. NAIL 1ST PIECE TO TRAILER FLOOR W/I-IM NAIL EVERY 8 INCHES. NAIL 2ND PIECE TO IST IN LIKE MANNER. 2 X 6 DOUBLED. NAIL IST PIECE TO TRAILER FLOOR W/6-16d NAILS. NAIL 2ND PIECE TO 1ST IN LIKE MANNER. o PAGE 6 TRUCKLOAD DATA NUMBEROF UNIT LO
28、ADS. . . . 5 NUMBEROF CRADLES . . . . . 10 1 1 BACKUPCLEAT I I I LIST OF MATERIAL AND NAILING DATA I LTL O-FT TRAILER (FLATBED) . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-! NIL-STD-1320 -83 BL W 77777LL 0070222 T M IL-STD -1 3 20-8 3 (NAVY) DE
29、TAIL PAGE 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.- M IL-STD-13 20-8 3 (NAVY) UNITIZING PROCEDURE UNIT PROTECTOR 1. USING A FORKLIFT TRUCK, STACK TWO UNIT LOADS TOGETHER FOWING A UNIT OF CRADLES FOUR (4) HIGH. 2. SECURE LOWER UNIT LOAD TO
30、TOP UNIT LOAD WITH TWO 1 1/4 X ,035 STEEL STRAPS POSITIONED AS SHOWN ABOVE. THREAD STRAP THROUGH FORK POCKETS OF THE TOP CRADLE OF THE LOWER UNIT LOAD AND THROUGH THE FORK POCKETS OF THE BOTTOM CRADLE OF THE TOP UNIT LOAD. LOCATE EDGE PROTECTORS UNDER STRAPS AS SHOWN, TENSION STRAPS, AND SEAL WITH O
31、NE SEAL DOUBLE NOTCHED OR TWO SEALS DOUBLE CRIMPED. STACKED CONTAINERS SHALL BE BROKEN DOWN TO UNIT LOADS AFTER UNLOADING THE VEHICLE. 3. PAGE B I WARNINGJ THE STRAPPING TOGETHER OF UNIT LOADS TO OW A UNIT OF CRADLES FOUR HIGH IS AUTHORIZED FOR LOADING AND UN- LOADING OF TRAILERS. ANY MOVEMENT OF FO
32、UR HIGH CRADLES SHALL BE LIMITED TO THAT NECESSARY TO LOAD OR UNLOAD THE TRAILER. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1320 -83 B1 7977711 0070224 3 m M IL-STD-13 2 0-8 3 (NAVY) UNITIZING PROCEDURE (CONT.) UNITIZING ONE UNIT LOAD PLUS ONE CRADLE 1 1/4 1 l/4 4 PU SEE PAGE SEE LTL NOTE 4 AND TABLE II, PAGE 4. V 1 1/4SEAL REVIEW ACTIVITIES: NA“ - OS, AS PREPARING ACTIVITY: NAVY - OS (PROJECT NO. 140 - W) PAGE 9 i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
