1、MIL-R-23057 43 06 0274377 T -, -7 - - 1L-B23057(ep) 2 October i961 MILITAEX SPECIFICATION REGULATOR, C0MPRF;SSED AIR, HIM PRECSw (3500 BI) This specification has been approved by the Bureau of Naval Weapons, Department of the Navy 1, SCOPE 1.1 air regulator. 2. APPLICABLE DCflMENTS This specificatio
2、n covers one type of high pressure, compreseed 2.1 The following specifications, etandards, drawings and publications, of the issue in effect on dates of invitation for bids, form a part of this Aeronautical and Associated Equipment, General Specifications for Parts and Equipment, Preparation for De
3、livery Pipe Threads, Taper, Aeronautical, National FOW, Screw Threads, b,%andard Optimum Selected Series; Cenerd Specification for Anodic-Coatings, for Alumimmi and Aluminum Alloy 8 Test Reports; Preparation of Drawings, Engineering and Assooiated Lista Symbol ANPT Sampling Procedures and Tables for
4、 Inspection by Attributes Marking of Shipments Identification Markings of U.S. Mllhy Prop er ty Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MILR -23057 ( Wep) DRAWINGS Force - Navy Aeronautical Standard Drawing AND1 0398 Metals - Definition of Ms
5、shilar FITBLICATINJ Air Force - Nam Aeronautical Bulletina i43 40 5 Specifications and Standards; Use of Storage Life - Aeronautical Articles (When requesting specifications, standards, and other publications cefer to both title and number. application to the Commanding Officer, Naval Supply Depot,
6、5801 Tabor Avenue, Philadelphia 20, Pennsylvania, Attention! Code CziS Copies of thfs specification and applicable mCjf;tCEbiME, it shall have a double amplitude of from 0.00 to 0,125 inch, and continuously varied frequency of from 600 to I000 cpn. and the regulator subjected to the test specified i
7、n paragraph L4.1.3. of 3500 psi gage, the regulator shall be cycled between 500 and 2800 psi gage on the outlet gage for at least 500 cycles. be subjected to the test specified in paragraph 4.4.1.3. After the 7 hour period, the regulator 4.3.3.1 After the 3 hour period, vibration shall be stopped 4.
8、3.4 Seasoni%.- With the regulator connected to an inlet pressure The regulator shall then 4.3.5 Sand and Dust.- The regulator, with gages attached and inlet and outlet openings tightly closed, shall be subjected to the Sand and Dust Test in accordance with Procedure I, of Specification MIL-E-5272. o
9、f the exposure in the dust chamber, the regulator and gages shail be tested for proper operation. Upon completion -6- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license
10、 from IHS-,-,-HILR -23057(Wep) 5e FREPARATION FOR IIELIVERY 5.1 Amlication,- The requirements of Section 5 apply only to direct 5.2 Preservath- The use of preservation compounds is not required 5.3 Packaginrt and Packing,- The regulator shall be packaged and packed purchases by or direct shipments t
11、o the Government. for this equipment in preparing for shipment and storage. for shipment in accordance with Specification MIL-P-7936 Levei A, B, or C, (see 6.31, 5.4 Marking of Simenta.- Interior packages and exterior shipping containers shall be marked in accordance with Standard MIL-STD-129. 5.4.1
12、 ReinsDection we- Unless otherwise specified, reinspection aiarkinga shall be in accordance with ANA Buletin No. 405. 6, NOTES 6.1 hntended Use.- The high pressure air regulator covered by this specification is for use on the high pressure side of portable air compressors to regulate the delivery ai
13、r of the compressors. 6.2 dering Data,- Procurement documents should specify the following: a. Title, nmber and date of this specification b, Selection of applicable levels of preservation, packing and packaging (See Section 51, o, Where the preproduction test sample should be sent and instructions
14、concerning the submittal of the test report (See 4.1.3) , NOTICE t When government drawings, specifications, or other data are used for any purpose other than in connection with a definitely related government procurement operation, the United States Government thereby incurs no responsibility nor a
15、ny obligation whatsoever; and the fact that the government may have formulated, furniehed or in any way supplied, the said drawings, specifications, or other data is not to be regarded by implication or othemdse as in any manner licensing the holder or any other person or corporation, or conveying any rights or permission .t;o manufacture, use or sell any patented invention that may in any way be related thereto. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
