1、Comments, suggestions, or questions on this document should be addressed to: Commander, Naval Sea Systems Command, ATTN: SEA 05M2, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160 or emailed to CommandStandardsnavy.mil, with the subject line “Document Comment”. Since contact
2、 information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 8010 INCH-POUND MIL-PRF-24763B(SH) 27 August 2009 SUPERSEDING MIL-E-24763A(SH) w/INT. AMENDMENT 1 9 August 2006 MIL-E-24763A(SH) 25 Aug
3、ust 1993 PERFORMANCE SPECIFICATION ENAMEL, EMULSION TYPE, FOR SHIPBOARD USE This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification c
4、overs the requirements of (95 percent acrylic) water based emulsion (latex), enamels primarily for use on primed metal surfaces. The enamel is volatile organic content (VOC) compliant and may be supplied in a variety of colors for shipboard use. 1.2 Classification. Enamel covered by this specificati
5、on is of the following types, classes and grades as specified (see 6.2). 1.2.1 Types. The types of enamel are designated by “Type II” or “Type III” as follows: Type I Material no longer used. Type II Air-drying, acrylic emulsion type with a VOC not greater than 250 grams per liter (g/L) (2.1 pounds
6、per gallon). Type III Air-drying acrylic emulsion type with a VOC less than 100 g/L (0.85 pounds per gallon). 1.2.2 Classes. The classes of the enamel are one of the following: Class 1 High gloss, 85 percent minimum. Class 2 Semi-gloss, 45 to 60 percent. Class 3 Low gloss, 7 to 12 percent 1.2.3 Grad
7、es. The grades of enamels are designated as follows: Grade A Standard pigmented Grade B Low solar absorbent (26173, 26270, 26373 and 26008) Grade C Low solar absorbent and anti-stain (26008 and 26270) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M
8、IL-PRF-24763B(SH) 2 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. Wh
9、ile every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standar
10、ds, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL SPECIFICATION TT-P-645 - Primer, Paint, Zinc-Molyb
11、date, Alkyd Type FEDERAL STANDARDS FED-STD-141 - Paint, Varnish, Lacquer and Related Materials: Methods of Inspection, Sampling and Testing FED-STD-313 - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials furnished to Government Activities FED-STD-595/10080 - Brown,
12、Gloss FED-STD-595/10324 - Brown, Gloss FED-STD-595/10371 - Brown, Gloss FED-STD-595/11105 - Red, Gloss FED-STD-595/11120 - Red, Gloss FED-STD-595/11136 - Red, Gloss FED-STD-595/12197 - Orange, Gloss FED-STD-595/12199 - Orange, Gloss FED-STD-595/12246 - Orange, Gloss FED-STD-595/12300 - Orange, Gloss
13、 FED-STD-595/13538 - Yellow, Gloss FED-STD-595/13591 - Yellow, Gloss FED-STD-595/13655 - Yellow, Gloss FED-STD-595/14062 - Green, Gloss FED-STD-595/14097 - Green, Gloss FED-STD-595/14120 - Green, Gloss FED-STD-595/14449 - Green, Gloss FED-STD-595/15042 - Blue, Gloss FED-STD-595/15044 - Blue, Gloss P
14、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-24763B(SH) 3 FED-STD-595/15048 - Blue, Gloss FED-STD-595/15092 - Blue, Gloss FED-STD-595/15102 - Blue, Gloss FED-STD-595/15182 - Blue, Gloss FED-STD-595/15200 - Blue, Gloss FED-STD-595/16081 - Gr
15、ay, Gloss FED-STD-595/16099 - Gray, Gloss FED-STD-595/16187 - Gray, Gloss FED-STD-595/16307 - Gray, Gloss (Bulkhead/equipment) FED-STD-595/16376 - Gray, Gloss FED-STD-595/16492 - Gray, Gloss FED-STD-595/17038 - Miscellaneous, Gloss (Black) FED-STD-595/17043 - Miscellaneous, Gloss (Gold) FED-STD-595/
16、17100 - Miscellaneous, Gloss (Dark purple) FED-STD-595/17142 - Miscellaneous, Gloss (Purple) FED-STD-595/17155 - Purple, Gloss FED-STD-595/17875 - Miscellaneous, Gloss (Light blue) FED-STD-595/17886 - Miscellaneous, Gloss (Soft white) FED-STD-595/17925 - Miscellaneous, Gloss (Bright white) FED-STD-5
17、95/20109 - Brown, Semigloss FED-STD-595/20117 - Brown, Semigloss FED-STD-595/21136 - Red, Semigloss FED-STD-595/23655 - Yellow, Semigloss FED-STD-595/23814 - Yellow, Semigloss FED-STD-595/24097 - Green, Semigloss FED-STD-595/25042 - Blue, Semigloss FED-STD-595/25048 - Blue, Semigloss FED-STD-595/251
18、02 - Blue, Semigloss FED-STD-595/26008 - Gray, Semigloss (Deck) FED-STD-595/26118 - Gray, Semigloss FED-STD-595/26173 - Gray, Semigloss (Ocean) FED-STD-595/26231 - Gray, Semigloss FED-STD-595/26270 - Gray, Semigloss (Haze) Provided by IHSNot for ResaleNo reproduction or networking permitted without
19、license from IHS-,-,-MIL-PRF-24763B(SH) 4 FED-STD-595/26307 - Gray, Semigloss (Bulkhead/equipment) FED-STD-595/26373 - Gray, Semigloss (Light) FED-STD-595/26492 - Gray, Semigloss FED-STD-595/27038 - Miscellaneous, Semigloss (Black) FED-STD-595/27875 - Miscellaneous, Semigloss (Light blue) FED-STD-59
20、5/27886 - Miscellaneous, Semigloss (Soft white) FED-STD-595/30109 - Brown, Flat or Lusterless FED-STD-595/30117 - Brown, Flat or Lusterless FED-STD-595/31136 - Red, Flat or Lusterless FED-STD-595/33655 - Yellow, Flat or Lusterless FED-STD-595/34097 - Green, Flat or Lusterless FED-STD-595/35042 - Blu
21、e, Flat or Lusterless FED-STD-595/35048 - Blue, Flat or Lusterless FED-STD-595/36118 - Gray, Flat or Lusterless FED-STD-595/36173 - Gray, Flat or Lusterless (Ocean) FED-STD-595/36231 - Gray, Flat or Lusterless FED-STD-595/36270 - Gray, Flat or Lusterless (Haze) FED-STD-595/36307 - Gray, Flat or Lust
22、erless (Bulkhead/equipment) FED-STD-595/36373 - Gray, Flat or Lusterless (Light) FED-STD-595/36492 - Gray, Flat or Lusterless FED-STD-595/37038 - Miscellaneous, Flat or Lusterless (Black) FED-STD-595/37875 - Miscellaneous, Flat or Lusterless (Light blue) FED-STD-595/37886 - Miscellaneous, Flat or Lu
23、sterless (Soft white) DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-23236 - Coating Systems for Ship Structures MIL-DTL-24441 - Paint, Epoxy-Polyamide, General Specification For MIL-DTL-24441/20 - Paint, Epoxy-Polyamide, Green Primer, Formula 150, Type III MIL-DTL-24441/29 - Paint, Epoxy-Polyamide, G
24、reen Primer, Formula 150, Type IV MIL-PRF-24635 - Coating Systems, Weather-Resistant, Exterior Use (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
25、 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.
26、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-24763B(SH) 5 CODE OF FEDERAL REGULATIONS 29 CFR 1910.1200, 1915.99, 1917.28, 1918.9, and 1926.59 - Hazard Communication 29 CFR 1990 - Identification, Classification, and Regulation of Carcinogen
27、s 40 CFR, Part 60, Appendix A, Method 24 - Determination of Volatile Matter Content, Water Content, Density, Volume Solids, and Weight Solids of Surface Coatings 40 CFR Part 261, Appendix II - Test method for evaluating solid waste physical/chemical methods, SW 846 (NSN-955-001-00000-1) 40 CFR 355 -
28、 Emergency Planning and Notification 40 CFR 372 - Toxic Chemical Release Reporting: Community Right-to-Know (Copies of these documents are available from the Superintendent of Documents, U.S. Government Printing Office, Washington DC 20401 or online at www.gpoaccess.gov/index.html.) STATE OF CALIFOR
29、NIA DEPARTMENT OF HEALTH SERVICES California Administrative Code Title 22, Division 4, Chapter 30. Minimum standards for Management of Hazardous and Extremely Hazardous Waste. Section 66699 Persistent and Bioaccumulative Toxic Substance and Section 66700Waste Extraction Test, Pg. 679-681 (Register 9
30、0, Nos. 38-41; 10-12-90). (Application for copies should be addressed to the Hazardous Material Laboratory, State of California, Dept. of Health Services, 2151 Berkeley Way, Berkeley, CA 94704) 2.3 Non-Government publications. The following documents form a part of this document to the extent specif
31、ied herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. ASTM INTERNATIONAL ASTM G154 - Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials ASTM D185 - Standard Test Methods for Coarse Part
32、icles in Pigments, Pastes, and Paints (DoD adopted) ASTM B209 - Aluminum and Aluminum-Alloy Sheet and Plate (DoD Adopted) ASTM D522 - Standard Test Method for Mandrel Bend Test of Attached Organic Coatings (DoD adopted) ASTM D523 - Standard Test Method for Specular Gloss (DoD adopted) ASTM D562 - St
33、andard Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using the Stormer-Type Viscometer (DoD adopted) ASTM D609 - Standard Methods for Preparation of Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products (DoD adopted) ASTM D660 - Standa
34、rd Test Method for Evaluating Degree of Checking of Exterior Paints (DoD adopted) ASTM D661 - Standard Test Method for Evaluating Degree of Cracking of Exterior Paints (DoD adopted) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-24763B(SH) 6
35、 ASTM D714 - Standard Test Method for Evaluating Degree of Blistering of Paints (DoD adopted) ASTM F718 - Standard for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet (DoD adopted) ASTM D823 - Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and
36、 Related Products on Test Panels (DoD adopted) ASTM D1014 - Standard Practice for Conducting Exterior Exposure Tests of Paints on Steel (DoD adopted) ASTM D1210 - Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems (DoD adopted) ASTM E1347 - Standard Test Method for Color and
37、Color-Difference Measurement by Tristimulus (Filter) Colorimetry ASTM D1654 - Standard Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments (DoD adopted) ASTM D2243 - Standard Method for Freeze-Thaw Resistance of Waterborne Coatings (DoD adopted) ASTM D2244 - Stan
38、dard Method for Calculation of Color Differences from Instrumentally Measured Color Coordinates (DoD adopted) ASTM D2805 - Standard Test Method for Hiding Power of Paints by Reflectometry (DoD adopted) ASTM D3168 - Standard Practice for Qualitative Identification of Polymers in Emulsion Paints (DoD
39、adopted) ASTM D3273 - Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber (DoD adopted) ASTM D3274 - Standard Test Method of Evaluating Degreee of Surface Disfigurement of Paint Films by Microbial (Fungal or Algal) Growth or Soil and
40、Dirt Accumulation (DoD adopted) ASTM D3278 - Standard Test Methods for Flash Point of Liquids by Setaflash Closed-Cup Apparatus (DoD adopted) ASTM D3335 - Standard Test Method for Low Concentrations of Lead, Cadmium, and Cobalt in Paint by Atomic Absorbtion Spectroscopy (DoD adopted) ASTM D3359 - St
41、andard Test Method for Measuring Adhesion by Tape Test ASTM D3891 - Standard Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products ASTM D4214 - Standard Test Methods for Evaluating Degree of Chalking of Exterior Paint Films (DoD adopted) ASTM D4400 - Stan
42、dard Test Method for Sag Resistance of Paints Using a Multinotch Applicator (DoD adopted) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-24763B(SH) 7 ASTM D4727/D427M - Standard Specification for Corrugated and Solid Fiberboard heet Rock (Co
43、ntainer Grade) and Cut Shapes (DoD adopted) (Copies of these documents are available from ASTM International, 100 Barr Harbor Dr., PO Box C700, West Conshohocken, PA 19428-2959 or online at www.astm.org.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a co
44、nflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS
45、 3.1 Qualification. The enamels furnished under this specification shall be products that are authorized by the qualifying activity for listing on the applicable qualified products list (QPL) before contract award (see 4.2, 6.2 and 6.3). 3.2 Recycled, recovered, or environmentally preferable materia
46、ls. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.3 Material safety data sheet (MSDS). Th
47、e contracting activity shall be provided a material safety data sheet at the same time of contract award. The MSDS shall be provided in accordance with the requirements of FED-STD-313. The MSDS shall be included with each shipment of the material covered by this specification (see 6.5). 3.4 Directio
48、ns for use. The contractor shall provide written directions on each container for the surface preparation, mixing, and applying of the enamel supplied and this direction shall include all information necessary to comply with OSHA Hazard Communication Standard and FED-STD-313. In addition, the contra
49、ctor shall provide an ASTM F718 data sheet which shall separately detail requirements for small unit (metric and English equivalents of pint, quart, and gallon) and large unit (5-gallon) containers. 3.5 Hazardous material. Manufacturers shall prepare container hazardous chemical warning labels for the paint in accordance with the requirements of 29 CFR Parts 1910.1200, 1915.99, 1917.28, 1918.90 and 192
