1、E- . I INCH-POUND 1 MI L-1-22 598EN AS 29 December 1989 SUPERSEDING MIL-I-22598A(AS 19 September 1978 MILITARY SPECIFICATION INTERPRETATION KIT, PHOTOGRAPHIC, POCKET-SIZE BS-5( This specification is approved for use by the Naval Air Systems Command, Department of the Navy, and i s available for use
2、by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for one (1) type of pocket photographic interpretation kit, containing viewing and measuring instruments,-for use in the field. 1.2 Classification. The interpretation kit shal
3、l be of one (1) type, designated BS-5( ) (See 3.7). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The fol lowing specifications and standards form a part of this document to the extent specified herein. otherwise specified, the issues of these documents are th
4、ose listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the sol ici tation (see 6.2). Unless Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document
5、should be addressed to Naval Air Engineering Center, Systems Engineering and Standardization Depart- ment (Code 53), Lakehurst, NJ 08733-5100 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 6675
6、 DISTRIBUTION STATEMENT A. Approved for pub1 ic release; distribution is un1 imi ted. -. THIS DOCUMENT CONTAINS /o PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-._- MIL-I-2257B bb W 7797706 0230670 5 9 c SPECIFICATIONS F ED ERAL GG-P-681 GG-
7、S-l61/5 SS-P-186 TT- I - 52 8 GGG-S- 1 808 PPP-B-636 MILITARY MIL-P-116 MI L-N-634 MIL-S-3629 MIL-C-4318 MIL-M-21039 STANDARDS . FEDERAL FED- S TD- 1 MILITARY MIL-STD-105 MIL-STD-129 MI L-STD- 1 30 MIL-STD-155 Protractor, Circular and Semicircular (Mils, Degrees) Scale, Drafting, Surveyors Pencil, M
8、echanical (including Leads and Erasers) Ink, Drawing, Waterproof, Black Screwdriver, Jewelers (Swivel Knob, Interchangeable B1 ades) Box, Shipping, Fiberboard Preservation, Methods of Navigators Plotting Instrument Set and Plotting Instruments Stereoscopes, Lens, Aerial Photograph Interpretation (Po
9、cket 1 Computer, Aerial Photographic Data Magnifier, Measuring Tube Type, Seven Power AR-60( ) a Standard for Laboratory Atmospheric Conditions for Testing Sampling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage Identification Marking of U.S. Military Property Jo
10、int Photographic Type Designation System (Unless otherwise indicated, copies of federal and military specifications and standards are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.2 Non-Government publications. The following
11、 document forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS ar
12、e the isssues of the documents cited in the solicitation (see 6.2). - AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM A580 - Wire, Steel, Stainless l! VI n wn - o- ? I! c4 * uu +m PCL np. nn nn nn 00 O0 O0 r- n nn OQ C we .- C .- .- u mmw 2 35 In m . I-m II N I cc .C .C E -12 mm O UN roa) nn
13、O0 m -In0 -QI- O E n n O ro nn O0 -N iON VI o) C c, c, al v) .r VI c, C al rd W W r .r a - VI o) C c, c, al v) .r VI c, C al m V W r .r nnn rinn O00 0Inm ro Oa)? -m NQI InN rou “E TE II II cc) .- c UV VIV) CO .r + 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license
14、 from IHS-,-,-3.4.6 Magnifier. The magnifier ,shall conform to the requirements of MIL-M-21039, except as specified herein. The magnifier shall be capable of resolving a minimum of fifty-six (56) lines per millimeter at the center of the field and a minimum of thirty-five (35) lines per millimeter a
15、t any edge of the field, when tested as specified in 4,7.3. 3.4.6.1 Reticle. Unless otherwise specified in the contract or purchase order, a single reticle, incorporating the type 6 and F scales specified in MIL-M-21039, shall be furnished with each magnifier. 3.4.7 Protractor. The protractor shall
16、be Type I, Class A, Style 1, Plastic in accordance with GG-P-681. The size (diameter) of the protractor shall be 4 i nches. 3.4.8 pen. The pen shall be a non-clogging technical fountain pen, Rapidograph Number 1 or equal. The pen shall have a tungsten carbide point or a synthetic jewel point. produc
17、e a continuous line 0.016 * 0.004 inch. The tip of the pen shall permit free flow of ink to 3.4.9 Pencil. The pencil shall be a Type IC, Cl3ss 1 glass and china marking . pencil in accordance with SS-P-186. The pencil shall be furnished with black glass marking lead 2.750 inch long by 0.120-inch in
18、diameter. Six (6) additional leads, two (2) each black, red, and blue, shall be provided and stored in the metal tube. 3.4.10 Metal tube. The tube shall be a thin-wall, two compartment metal capsule capable of holding the extra set of needle points for the divider specified in 3.4,3 an the six (6) g
19、lass marking leads for the pencil specified in 3.4.9. . 3.,4.11 Screwdriver. The screwdriver shall be Type 1 in accordance wi th GGG-S-1808. The screwdriver shall be supplied with one blade. The blade shall be sized to properly engage the screwhead slots of the computer and the di vider. 3.5 Weight.
20、 The weight of the interpretation kit, with all of the components in place, shall not exceed two (2) pounds. 3.6 Finish. The finish of all components of the kit shall conform to the highest grade specified. The finish of the carrying case shall conform to the best commercial practice for high-grade
21、drafting instrument cases. 3.7 Type designator. The parenthesis in the type designator will be replaced by a suffix letter and, when appropriate a production issue number, in accordance with the provisions of MIL-STO-155. This complete type designator shall then be used on nameplates, shipping recor
22、ds, in instruction books, and wherever reference is made to the specific equipment defined by the designator. As soon as possible, after award of the contract, the contractor should apply to the contracting officer for such information. 3.8 Identification marking. The identification marking of the i
23、nterpretation kit shall be hot stamped in gold on the top or lid of the carrying-case. The marking shall conform to the requirements of MIL-STO-1 30. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.9 Workmanship. The workmanship shall be of the h
24、ighest grade in accordance with the best commercial practice for precision drafting instruments. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the cantract or purchase order, the contractor is responsible for the performance of all inspection requir
25、ements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Governm
26、ent reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items sha of sections 3 and 5. The inspection set forth in
27、th become a part of the contractors overall inspection program. The absence of any inspection requirements shall not relieve the contractor of the responsibili Droducts or sumlies submitted to the Government for 1 meet all requirements s spec fication shall system or quality in the specification y o
28、f ensuring that all acceptance comply with - ill requiremenis of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascert2in conformance to requirements, however, this does not authorize submission of known defective material, either indicated or ac
29、tual, nor does it commit the Government to accept defective material. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.4) b. Quality conformance inspection (see 4.5) c. Individual inspection (see 4.6) 4.3 Te
30、st conditions. The interpretation kit shall be inspected under conditions of temperature and humidity as specified in FED-STO-1. 4.4 First article inspection. The first article inspection shall consist of the individual examinations of 4.6 and all examinations and tests of 4.6, 4.7, and 4.8. Failure
31、 of the sample to pass any examination or test shall constitute failure of the first article inspection. 4.5 Qual i ty conformance inspection. The qual i ty conformance inspection shall consist of all examinations and tests specified in 4.6 and 4.8. For inspections of 4.8, one sample pack shall be s
32、elected at random from each lot and inspected. 4.5.1 Sampling accordance with Inspection Leve Sampling for the quality conformance inspections shall be in MIL-STD-105, using the Single SampTing Plan (see 6.3), II. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license
33、 from IHS-,-,-MIL-I-2257B bb M 777770b 0230b7b b MI L- 1-22 598B(AS 1 4.5.2 Lot. The lot shall consist of all of the interpretation kits offered for del i very at one time on any one contract or order. 4.6 Individual inspection. Each interpretation kit shall .be examined to determine conformance to
34、the requirements of 3.4, 3.4.1.1, 3.4.1.3, 3.4.5, and 3.8. The contractor shall furnish certification to the Government for approval, prior to shipment of any material, that the components furnished in the interpretation kit have been inspected in accordance with the documents specified herein and c
35、onform to all of the requirements of this specification. 4.7 Examinations and tests. 4.7.1 Visual and dimensional examinations. Examine the kit and each individual item in the kit visually and with qauqes to determine conformance to the requirements of this specifjcation with rspect to materials, co
36、nstruction, dimensions, weight, contents of the kit, finish, identification marking, and workmanship. Determine that the components of the kit are easily removable from the case compartments. Determine that the table of equivalents can be read without removal from the case. Examine the lens mounts a
37、nd leg terminal inserts of the stereoscope for proper fit and function. Determine that the screwdriver blade properly engages the screwhead slots of the computer and divider. Determine that the carrying case lies flat with and . without the components in place. 4.7.1.1 Drawing examinations. With the
38、 pen fitted with India ink conforming to TT-1-528, and using a straight edge, draw ten lines on photographic film. Each line shall be approximately eight inches long. Allow the ink to dry, Examine the inked lines, visually and with gauges, to determine conformance with the requirements of 3.4.8. 4.7
39、.2 Stereoscope. The stereoscope shall be inspected in accordance with Section 4 of MIL-S-3629 to determine conformance to the requirements of 3.4.2. 4.7.3 Magnifier and reticle. The magnifier shall be inspected in accordance with Section 4 of MIL-M-21039 to determine conformance to the requirements
40、of 3.4.6, 4.7.4 Computer. The computer shall be inspected in accordance with Section 4 of MIL-C-4318 to determine conformance to the requirements of 3.4.4. 4.7.5 Other components. The drafting divider, drafting scale, protractor, and glass marking pencil shall be inspected in accordance with the req
41、uirements of MIL-N-634, GG-S-161/5, GG-P-681, and SS-P-186 respectively to determine conformance to the requirements of 3.4.3, 3.4.5, 3.4.7, and 3.4.9. 4.8 Packaging inspection. Packaging shall be inspected to determine conformance to the requirements of Section 5. 5. PACKAGING 5.1 Preservation . In
42、terpretation kits shall be clean and dry prior to packaging. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-b MIL-I-2259B bb = 0b 0230b77 8 m 5.1.1 Unit pack. One (1) complete interpretation kit, with components i nstai led in the carrying case, s
43、hall be packed in accordance with MIL-P-116, Met hod I C-2. 5.1 .? intermediate pack. Twelve (12) unit-packed interpretation kits shall be packed into a Tnug-fitting box conforming to PPP-B-536, Type CF, Class-domestic. This intermediate pack shall be closed in accordance with the Appendix to PPP-B-
44、636. 5.2 Packing. Packing shall be Level A or Commercial as spec 5.2.1 Level A. Interpretation kits packaged as specified in packed in a corrugated fiberboard box conforming to PPP-8-636 Weather resistant, Variety SHI Grade N6C1 Style RSC. Closure be in accordance vi th the Appendix to PPP-8-636. 5.
45、2.2 Commercial. Interpretation kits packaged as specified be packed to meet carrier acceptance and safe 4eliverv to the fied. (See 6.2). 5.1.2, shall be Type CF, Class- of the 5ox shall in 5.1.2, shall destination at the. lowest rate in compliance with the requirements o? carrier rules and regulatio
46、ns applicable to the mode of transportation. 5.3 Marking Unit packages, intermediate packages, and exterior shipping containers shall be marked in accordance with MIL-STD-129, 6. NOTES 6.1 Intended use. The pocket size photographic interpretation kit is intended to provide the photographi c interpre
47、ter with the necessary equipment to analyze aerial photographs in the field. 6.2 Ordering data. Acquisition documents should specify the following: a. Title, number, and date of this specification. b. Part number of interpretation kit (see 6.4). c. Quantity of interpretation kits required. d. Issue
48、of DODISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced (see 2.1.1 and 2.2). e. Whether or not first article inspection is required (see 3.1 and 6.31. f. Acceptable quality level, if different (see 4.5.1). g. Level of preservation and packagi
49、ng required (see Section 5). 6.3 First article. interpretation kit, representati ve of the production model , wi 11 be furni shed for the inspection. instructions in acquisition documents regarding arrangement for examinations, approval of first article test results and disposition of the first articles. Invitations for bids should provide that the Government reserves the right to waive the requirement for samples for first article inspection to those bidders o
