1、AMSC N/A FSC 6210 INCH-POUND MIL-DTL-16377/84 18 December 2008 DETAIL SPECIFICATION SHEET FIXTURES, LIGHTING; T8 FLUORESCENT, EMERGENCY LIGHTING 54 WATTS, 120 VOLTS, 60 HERTZ, WATERTIGHT, SYMBOLS 333.1T8EM, 333.2T8EM, 342.2T8EM, AND 342.3T8EM This specification is approved for use by the Naval Sea S
2、ystems Command and is available for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-16377. All dimensions in inches. For tolerances, other than specified herein, see 3.
3、5.2 of MIL-DTL-16377. FIGURE 1. Typical view of symbols333.1T8EM and 342.2T8EM, symbols 333.2T8EM, and 342.3T8EM use identical construction with flush mounting flange not shown. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-16377/84 2NOTES:
4、 1. Symbols 333.2T8EM and 342.3T8EM use identical battery test switch construction with additional switch hardware (not shown) for switch operation below ceiling. 2. Type II label required on all fixtures. FIGURE 2. Typical section for symbols 333.1T8EM and 342.2T8EM. FIGURE 3. Typical section for s
5、ymbols 333.2T8EM and 342.3T8EM. FIGURE 4. Flush mounting dimension for symbols 333.2T8EM and 342.3T8EM. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-16377/84 3FIGURE 5. Standard mounting dimensions utilizing shock mounts for symbols 333.1T
6、8EM and 342.2T8EM. NOTES: 1. The black and red input conductors are the only switched power leads to the fixture, used for normal on/off lamp control. 2. The white and green input conductors shall be connected directly to the power source and remain continuously energized for emergency lamp battery
7、charging. The white and green input conductors shall not have power interrupted by on/off control switches. 3. The white input conductor is shared by the normal lamp circuits (white and red) and by the emergency circuit. FIGURE 6. Typical wiring diagram. Provided by IHSNot for ResaleNo reproduction
8、or networking permitted without license from IHS-,-,-MIL-DTL-16377/84 4FIGURE 7. Candela distribution curves, white diffusing window, symbols 333.1T8EM and 333.2T8EM. FIGURE 8. Candela distribution curves, prismatic window, symbols 342.2T8EM and 342.3T8EM. Provided by IHSNot for ResaleNo reproductio
9、n or networking permitted without license from IHS-,-,-MIL-DTL-16377/84 5FIGURE 9. Candela distribution curves, emergency mode. TABLE I. Numerical candela distribution curves, white diffusing window, symbols 333.1T8EM and 333.2T8EM. Candela distribution Candela distribution Vertical angle 0-degree 9
10、0-degree Vertical angle 0-degree 90-degree 0 786 786 95 8 62 5 781 783 105 6 39 15 745 760 115 4 26 25 677 709 125 3 17 35 582 634 135 0 10 45 469 540 145 0 3 55 353 436 155 0 0 65 234 323 165 0 0 75 120 211 175 0 0 85 27 124 180 0 0 90 9 89 Provided by IHSNot for ResaleNo reproduction or networking
11、 permitted without license from IHS-,-,-MIL-DTL-16377/84 6TABLE II. Numerical candela distribution curves, prismatic window, symbol 342.2T8EM and 342.3T8EM. Candela distribution Candela distribution Vertical angle 0-degree 90-degree Vertical angle 0-degree 90-degree 0 910 910 95 8 48 5 904 910 105 6
12、 26 15 872 906 115 5 22 25 810 881 125 3 15 35 713 817 135 1 9 45 577 709 145 0 4 55 378 566 155 0 1 65 195 381 165 0 0 75 88 227 175 0 0 85 30 119 180 0 0 90 9 76 TABLE III. Numerical candela distribution, emergency mode. Candlepower Candlepower Symbol number Symbol number Angle 0-degree 90-degree
13、Angle 0-degree 90-degree 0 56 56 95 8 0 5 56 55 105 4 0 15 54 53 115 3 0 25 51 48 125 2 0 35 46 41 135 1 0 45 41 33 145 1 0 55 35 25 155 0 0 65 28 17 165 0 0 75 21 8 175 0 0 85 14 2 180 0 0 90 10 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-
14、DTL-16377/84 7PHOTOMETRIC DATA: Photometry reports based on LM-41 and other pertinent IESNA procedures. Plane: zero degrees is parallel to lamps, 90 degrees is perpendicular to lamps. Electrical values: 120 volts, 60 hertz, 53.7 watts+4.0 watts (battery charging circuit)=57.7 watts total. Ambient te
15、mperature: 251 C. Lamps: GE F17T8-SP41-ECO (seasoned for at least 100 hours). Lamps correction: lamps rated at 1325 lumens. Ballast: Furnished with fixture, see MIL-DTL-16377/81 for 17-watt lamp specification, MIL-DTL-16377/77 for emergency ballast specification. REQUIREMENTS: CLASSIFICATION: Type:
16、I (Fluorescent). Class: 2 (General). SYMBOL NUMBERS: 333.1T8EM: Complete lighting fixture assembly, standard mounting, with three 17-watt cool white fluorescent lamps and white diffusing window assembly, includes emergency battery/ ballast circuit for emergency lighting. 333.2T8EM: Complete lighting
17、 fixture assembly, flush mounting, with three 17-watt cool white fluorescent lamps and white diffusing window assembly, includes emergency battery/ ballast circuit for emergency lighting. 342.2T8EM: Complete lighting fixture assembly, standard mounting, with three 17-watt cool white fluorescent lamp
18、s and clear and white prismatic window assembly, includes emergency battery/ ballast circuit for emergency lighting. 342.3T8EM: Complete lighting fixture assembly, flush mounting, with three 17-watt cool white fluorescent lamps and clear and white prismatic window assembly, includes emergency batter
19、y/ ballast circuit for emergency lighting. DESIGN: Electrical rating: 51 watts, 120 volts, 60 hertz, ungrounded electrical distribution system. Total input power: 53.7 watts+4.0 watts (battery charging circuit)=57.7 watts. Total at 120 volts. Dimension and configurations: See figures 1, 2, and 3. Ph
20、otometric data: See figures 7, 8, 9, and tables I, II, III. Wiring diagram: See figure 6. Ballast: See MIL-DTL-16377/81 for 17-watt lamp specification, MIL-DTL-16377/77 for emergency ballast specification. Mounting dimensions: Symbols 333.1T8EM and 342.2T8EM: Standard mounting (surface), see figure
21、5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-16377/84 8Symbols 333.2T8EM and 342.3T8EM: Flush mounting (recessed), see figures 4. Window assembly: Symbols 333.1T8EM and 333.2T8EM: White window, see table IV and figure 27 of MIL-DTL-1637
22、7. Symbols 342.2T8EM and 342.3T8EM: Prismatic window, see table IV and figure 27 of MIL-DTL-16377. Enclosure: Watertight; see 3.5.11 of MIL-DTL-16377. Cable: 10 feet (minimum) of type LSFHOF-3 in accordance with MIL-DTL-24643/3 Weight: Symbols 333.1EM and 342.2EM: Not to exceed 20 pounds. Symbols 33
23、3.2EM and 342.3EM: Not to exceed 22 pounds. DESIGNATION AND MARKING: The following labels shall be furnished in accordance with MIL-DTL-16377 applied as shown on figures 1 and 3. a. Two type I labels, equipment identification, reference MIL-DTL-16377 figure 11, shall include manufacturer and address
24、, one located on back and other located on an inner nonreflecting surface. b. One type II label, circuit wiring information, reference MIL-DTL-16377 figure 12, located on outside surface adjacent to cable entrance. c. Two type IV label, repair parts, reference MIL-DTL-16377 figure 14, information to
25、 be shown shall include “USE THE FOLLOWING REPAIR PARTS ONLY.“ List all standard parts shown in table IV, located on an inner nonreflecting surface and back of fixture. d. One type IV label, reference MIL-DTL-16377 figure 14, information to be shown shall be “CHARGING INDICATOR LIGHT”. e. One type I
26、V label, reference MIL-DTL-16377 figure 14, information to be shown shall be “BATTERY ENABLE”. f. One type V label, reference MIL-DTL-16377 figure 15, information to be shown shall be “DURING MAINTENANCE, PROTECTIVE DEVICE MUST BE OPENED OR PULLED TO SECURE AC POWER TO THIS FIXTURE AND THE BATTERY E
27、NABLE SWITCH MUST BE IN THE OFF POSITION”. EXAMINATIONS AND TESTS: Examinations and tests shall be as specified in MIL-DTL-16377 as follows: First article testing/inspection: Complete fixtures: See table VII. Window assemblies: See table VIII. Comparison inspection: See tables VII and VIII. Conforma
28、nce inspection: See MIL-DTL-16377. Inspection of product for delivery: Examination See MIL-DTL-16377. Conformance test See MIL-DTL-16377. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-16377/84 9Examination for preparation of delivery See MI
29、L-DTL-16377. GENERAL INFORMATION: Table IV. Fixture standard parts. Table V. Complete fixture first article tests. Table VI. Window assembly first article tests. Table VII. Complete fixture part numbers. NOTES: 1. See MIL-DTL-16377/42 for T8 color filter tube specifications and part numbers. 2. Inst
30、allation circuit wiring shall incorporate a minimum ratio of eight 17-watt lamps and one emergency 17-watt lamp. The 8 to 1 ratio is required for meeting MIL-STD-1399-300 harmonic requirements. The 17-watt emergency ballast produces non-linear current that must be offset by the linear current from e
31、ight 17-watt lamp ballasts connected to the same circuit. 3. Emergency fixtures may be designated as Navy Emergency Automatic Lighting System or NEALS. 4. The “battery enable” switch shall be placed in the normal position after installation. TABLE IV. Standard parts. Name Military p/n or specificati
32、on National Stock Number (NSN) Remarks Lamp Commercial identification F17T8/CW 6240-01-391-6027 - Lamplock M16377/40-003 - -Lampholder UL Standard 542 6250-00-284-0481 Commercial Ballast M16377/81-001 - Integrated starter type Shockmount M16377/41-008 6210-01-393-4302 0.067 steel, zinc plated Window
33、 assembly, diffusing M16377/12-001 6210-00-295-2849 1/Window assembly, prismatic M16377/12-003 6210-00-725-9030 1/Emergency ballast, wiring harnesses, and mating connector M16377/77-001 6250-01-491-7039 Complete assembly: includes wiring harnesses and matting AMP #206043 connectors. Charging indicat
34、or light - 6220-01-415-7889 LED type Switch, battery enable M16377/75-008 5930-01-414-9240 DPST Switch, battery test Carling 2167-M-A-NC-73XCA4 - Momentary toggle Switch cover, rubber boot MIL-DTL-5423/2 - Neoprene NOTE: 1/Window assemblies (diffusing and prismatic) are the same as T12 lamp fixtures
35、 (MIL-DTL-16377/12). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-16377/84 10TABLE V. First article tests and comparison inspection for complete fixtures.1/Test Requirement Test method Remarks Examination 3.13 4.5 - Operation 3. 4.8.1 -Ele
36、ctromagnetic Interference 3.6.14 4.8.16 - Electrical equipment interface testing requirements: MIL-STD-1399-300 MIL-STD-1399-300 MIL-STD-1399-300 2/, 3/Dielectric withstanding voltage 3.6.15 4.8.2 4/ Insulation resistance 3.6.16 4.8.3 4/ Enclosure effectiveness 3.5.11 4.8.14.4 4/Shock 3.5.12 4.8.7 4
37、/ Vibration 3.5.13 4.8.8 4/ Enclosure effectiveness 3.5.11 4.8.14.4 4/Dielectric withstanding voltage 3.6.15 4.8.2 4/Insulation resistance 3.6.16 4.8.3 4/Noise 3.5.14 4.8.9 - Continuity of grounding 3.6.13.4 4.8.12 - Light output 3.7.1 4.8.6.1 - Optical uniformity 3.7.4.1.1 4.8.4 - Stress relief 3.8
38、.5.3 4.8.5 - Magnetic permeability 3.4.8 4.8.18 - Emergency light output: Distribution curves shall be documented during emergency lamp operation 3.7.1 4.8.6.1 5/Emergency ballast performance: Operating time and discharge test See MIL-DTL-16377/77, Table II, battery discharge test See MIL-DTL-16377/
39、77,Table II, battery discharge test - NOTES: 1/Requirements and test methods use MIL-DTL-16377. 2/If less, then 1KVA exception not applicable for input waveform THD. 3/Solid state components shall be subject to 250 positive spikes and 250 negative spikes, (500 total spikes), one spike per minute, us
40、ing testing method identified in MIL-STD-1399-300. 4/Tests shall be performed in the order specified. 5/Shall meet or exceed published distribution curves. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-16377/84 11TABLE VI. First article tes
41、ts and comparison inspection for window assemblies.1/Test Requirement paragraph Test paragraph Remarks Examination 3.13 4.5 - Optical uniformity 3.7.4.1.1 4.8.4 - Stress relief 3.8.5.3 4.8.5 - Shock 3.5.12 4.8.7 2/Vibration 3.5.13 4.8.8 2/Enclosure effectiveness 3.5.11 4.8.14.4 2/Light output 3.7.1
42、4.8.6.1 Candela distribution NOTES: 1/Testing requirements and methods use MIL-DTL-16377. 2/Tests shall be performed in the order specified. TABLE VII. Complete fixture part numbers. Name Military p/n Complete fixture, Symbol 333.1T8EM M16377/84-333.1T8EM Complete fixture, Symbol 333.2T8EM M16377/84
43、-333.2T8EM Complete fixture, Symbol 342.2T8EM M16377/84-342.2T8EM Complete fixture, Symbol 343.3T8EM M16377/84-342.3T8EM Custodians: Preparing Activity: Army CR4 Navy SH Navy SH (Project 6210-2006-008) Air Force 99 Review Activities: Navy AS, CG Air Force 03 DLA GS2 GSA FAS NOTE: The activities list
44、ed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
