1、MIL-DTL-LSOL4 m 7777706 2059223 3LT m MEASUREMENT SENSITIVE MIL-DTL-l5014(AS) 26 November 1997 SUPERSEDING IN PART 4 April 1989 MIL-M-8 1929B(AS) DETAIL SPECIFICATION MANUALS, TECHNICAL: SEPARATE ILLUSTRATED PARTS BREAKDOWN; TECHNICAL CONTENT REQUIREMENTS (WORK PACKAGE CONCEPT) This specification is
2、 approved for use by the Naval Air Warfare Center, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense, within the distribution limitations noted at the bottom of this page 1. SCOPE 1.1 Scope. This specification prescribes the technical conte
3、nt requirements for the preparation of separate illustrated parts breakdown (TPB) manuals and IPB figures for use in another manual. 1.2 Classification. The type of manual is a combination of the technical content (functional elements covered) and the assigned level(s) of maintenance to be covered.
4、The maintenance level(s) covered is identified by using a prefix for the applicable functional element(s), as the first part of the publication title, as prescribed in MIL-DTL-8 1927. The assigned maintenance level(s) and functional elements to be covered should be as prescribed in the contract. 2.
5、APPLICABLE DOCUMENTS Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Air Warfare Center Aircraft Division, Code 414100B120-3, Highway 547, Lakehurst, NJ 08733-5100 by using the
6、Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A AREA TMSS DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction
7、or networking permitted without license from IHS-,-,- MIL-DTL-15014 999990b 2059224 25b MIL-DTL-15014 (AS) 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification
8、or recommendation for additional Somation or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2
9、.2 Government documents. 2.2.1 Stlecifications. standards and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified in the contract, the issues of these documents are those listed in the issue of the
10、Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-DTL-8 1927 - Manuais, Technical: Work Package Style, Format, and Common Technical Content Requirements; General Specification for
11、 (Work Package Concept). (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191 11-5094.) 2.2.2 Other Government documents. drawings and publications.
12、The following other Government documents, drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. PUBLICATIONS FEDERAL Cataloging Handbooks Cataioging Handbook 4m8 H-6 - Commercial and Governme
13、nt Entity (CAGE) Codes. - Federal Item Name Directory for Supplying Cataloging. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-L5014 = Ob 2059225 192 MIL-DTL- 1 50 14 (AS) NAVAL AIR SYSTEMS COMMAND NAVAIR 00-25-100 - Technical Manual Progr
14、am. NAVAIR 00-25-300 - Technical Directives System. NAVAIR 00-25-700 NAVAIR O 1 - 1 A-23 - Guide to General Style and Format of Work Package Technical Manuals. - Standard Maintenance Practices for Miniature/ Microminiature (2M) Electronic Assembly Repair. NAVAL SUPPLY SYSTEMS COMMAND P2300 Series -
15、Data Set. (Copies of Cataloging Handbooks H-4, H-6 and H-8 are available from the Commander, Defense Logistic Service Center, Battle Creek, MI 49017-3084. Copies of manuals are available by request to: Commanding Officer, Naval Air Technical Services Facility (NATSF), 700 Robbins Avenue, Philadelphi
16、a, PA 191 11-5097. The P2300 series is part of NAVSUP Publication 600. NAVSUP Publications 6OOD (for Government personnel) and 600F (for contractors) are available from the Naval Inventory Control Point Philadelphia, FkblicatiodForms Branch, 700 Robbins Avenue., Philadelphia, PA 19 1 1 1-5098.) 2.3
17、Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3
18、. REQUIREMENTS 3.1 General. a. Covrid ts and advertising. Copyrigk material shall not be included in any publication prepared in accordance with this specification without written permission of the copyright owner. Proprietary legends shall not be shown. The manual shall not contain advertising matt
19、er. All material prepared in accordance with this specification shail be Government property. b. Proprietary data. The Government shall have unlimited right to the data prepared under this specification. Proprietary legends are not acceptable in technical manuals. The preparing activity shall disclo
20、se, in narrative or pictorial display, that information 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. * MIL-DTL-15014 (AS) necessary to fulfill the requirements of this specification without disclosing that portion of the manufacturing process
21、that the preparing activity wishes to safeguard. c. Conflict between specifications. When conflict exists between MIL-DTL-8 1927 and the technical content requirements described herein, this specification shall take precedence. When conflict exists between the contract and this specification, the co
22、ntract shail take precedence, d. General stvle and format. Manuals shall be prepared to work package (WP) concept. General style and format shall be as specified in MIL-DTLS 1927. 3.1.1 General arran-ement of a seuarate IPB manual. When specified in the contract, a separate IPB manual shall be prepa
23、red (see 6.2). It shall be arranged as follows: a. Front matter (see 3.2.1). b. Alphabetical index (see 3.2.2). c. Numerical index of part numbers (see 3.2.3). d. Numerical index of reference designations (see 3.2.4). e. Technical content, IPB figures (see 2.3.6). 3.1.2 Arrangement of IPB multimanua
24、l set. When a separate IPB is prepared, it may be divided into a set of manuals. Each manual of the set will be assigned a separate publication number. Each manual shall cover one or more related subjects, e.g., indexes, power plant and related systems, automatic flight controls, etc. The fist manua
25、l of the multimanual set shall be the IPB index. 3.1.2.1 IPB multhnuai set index. A manual shall be prepared containing the IPB related indexes and the IPB introduction for multimanual set. The manual sha be arranged in the following order: a. Front matter (see 3.2.1). b. Multimanual set alphabetica
26、l index (see 3.1.2.1.1). c. Numerical index ofpart numbers (see 3.2.3). d. Numerical index of reference designations (see 3.2.4). 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-DTL-LSOL4 D 99999Ob 2059227 Tb5 MIL-DTL- 1 50 14 (AS) 3.1.2.1.1 D
27、ivision of an IPB multimanual set index. If it is anticipated that a revision of an existing IPB index or the initial issue of an IPB index exceeds reasonable size for handling (bulk is over three inches thick), a logical division of the information to be covered shall be established and the manual
28、divided into two or more volumes. The title page of each volume shall contain a continuation notice in accordance with MIL-DTL-81927. Each volume will be assigned a publication number. If possible, division of the information shall be by hctional element and the publication title shall reflect the v
29、olumes content. Each volume of the manual shall include an appropriate sub-title, e.g., Volume I, Alphabetical Index and Introduction; Volume II, Numerical Index of Part Numbers; Volume III, Numerical Index of Reference Designations, etc. 3.1.2.2 Technical content IPB manuals second and subsequent m
30、anuals of a multimanual set). Separate manuals shall be prepared for separate systems such as airframe hydraulic systems or power plant. Division by subject(s) shall be compatible with the breakdown of the associated maintenance manual. The manuals shall be arranged in the following order: a. Front
31、matter (see 3.2.1). b. Alphabetical index (see 3.2.2). c. Technical content, IPB figures (see 3.2.5). 3.1.3 Division of an existing IPB manual. When an existing IPB manual (after distribution of the basic issue) exceeds reasonable size for handling (b the change number only shall be placed on each c
32、hanged page in the upper left corner in normal bold type. d. Pane identification. including page numbering. Page identification is used for separate IPB manuais to reduce change impact and to permit muitiple addition of IPB figures in their proper location as required by their relationship without m
33、ajor change to the existing figure numbers on manual revision. The page number is part of the page identification system with the exception of the IPB figures. IPB figures use sequentially numbered pages for each figure and the figure numbers suffix is used to add new figures. The figure number or p
34、age identification, as applicable, shall be placed in the extreme upper right corner of the reproduction area, on the same line as the requiring activitys publication number, in very large bold type. (1) Numerical index of effective figuredpages. The pages of the index shall be identified by the wor
35、d “Page“, followed by sequentially assigned upper case letters, beginning with the letter A., e.g., Page A., Page B, Page C, etc. (2) List of Technical Publication Deficiencv Reports TDPRs) incomorated Danes. The page(s) of the list shall be identified by the acronym I TPDR“, followed by a dash (-)
36、and sequentially assigned Arabic numerals, beginning with the number one (i), e.g., “TPDR- 1, TPDR-2“. (3) Introduction papes. The pages of the introduction shall be identified by the acronym I INTRO“, followed by a dash (-) and sequentially assigned Arabic numerals, beginning with the number one (i
37、), e.g., “INTRO-1, INTRO-2“. (4) Aiphabetical index pages. The pages of the index shall be identified by the word INDEX, followed by a dash (-) and sequentially assigned Arabic numerals, beginning with the number one (i), e.g., “INDEX-1, INDEX-2“. (5) Numerical index of art numbers and numerical ind
38、ex of reference designations pages. Numerical index pages shall be identified using a six-digit numbering system (refer to NAVAIR 00-25-700 for detailed information). The intent of this numbering system is to reduce renumbering of a substantial number of pages when adding or deleting tabular data. T
39、he index pages shall be identified by a four-digit page number, followed by a dash (-) and a two-digit sufx permitting up to 99 expansion pages. The page number is prefixed with an upper case letter used to idene the specific index: “N“ is used for the Part Number Index and “R“ is used for the Refer
40、ence Designation Index, e.g., “NO00 1-00, N0002-00, etc. or ROO0 1-00, ROOO2-00“. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-DTL-L5014 W 9999906 2059230 55T W MIL-DTL-15014 (AS) (6) IPB fime Rages. IPB figures are identified by separate f
41、igure numbers and page numbers, (refer to NAVAIR 00-25-700 for detailed information). (a) IPB fime numbers. IPB figure pages shall be identified using a six-digit numbering system (refer to NAVAIR 00-25-700 for detailed information). The intent of this numbering system is to reduce renumbering of a
42、substantial number of figures when adding or deleting IPB figures. The figure shail be identified by a four-digit figure number, followed by a dash (-) and a two-digit su The marginal copy shall be in accordance with 3.1.4. b. Title block. The title block shall be placed below the marginal copy. The
43、 following information shall appear in the title block, in the order listed, as applicable: (1) A one-point de shall be placed below the marginal copy. (2) The title “NUMERICAL INDEX OF REFERENCE DESIGNATIONS“ shall be centered below the one point de. (3) End item nomenclature shall be centered belo
44、w the title. (4) A one-point rule shall be placed below the last line of information. c. Column heads. The column heads “REF DES,“ AND “FIGUREANDEX NUMBER“ or “PUBLICATIONFIGURE/INDEX NUMBER“ shall be placed below the title block. The column head “USABLE ON CODE“ may be added (see 3.2.4.3c), if requ
45、ired. The column heads shall be underlined. 3.2.4.2 Second and subsequent pages of the numerical index of reference designations . a. Marginal copy. The marginal copy shall be in accordance with 3.1.4. b. Column heads. The column heads “REF DES,“ and “FIGURE/INDEX NUMBER“ or “PUBLICATION/FIGURE/TNDE
46、X NUMBER“ shall be placed below the marginal copy. The column head “USABLE ON CODE“ may be added (see 3.2.4.3c), ifrequired. The column heads shall be underlined. 23 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15014 999990b 2059246 917 =
47、MIL-DTL-15014 (AS) 3.2.4.3 Development of the numericai index of reference designations. The numerical index shal be prepared as follows: a. “REF DES“ column. The reference designations column is used to establish the content. All reference designations identifed in any IPB figure contained in the m
48、anual shall be listed in reference designation sequence or in normal computer (ASCII code) Ascending Numeric/Alpha, reference designation sequence, as follows: (1) Multiple identical assemblies (same reference designations). When multiple reference designations apply to the same PB figure (e.g., cir
49、cuit card assembly), all detail part reference designations shali be listed in the rst appearance in the manual. (a) Second and subsequent items may reference the rst item to reduce unnecessary redundant entries in the index. (b) The second and subsequent reference designations shall reference the end item breakdown figure and reference first related item, e.g., “BDKN same as A3“ or “See A3 for BDKN.“ (c) The most cost eff
